Product ID:ENAMEL,ALKYD,CAMOUFLAGE,DESERT SAND 754806
MSDS Date:03/20/1987
FSC:8010
NIIN:00-111-8353
MSDS Number: BCZGJ

PRATT & LAMBERT, INC. - INDUSTRIAL COATINGS DIV.

16116 E 13TH ST
WICHITA, KS 67201
US

Preparer: W.A. ELLISON

Cage: FO127

PRATT AND LAMBERT INC

22 CLEVELAND, OH 44101-1027 US

Telephone: 216-566-2902

Cage: 61196

MINERAL SPIRITS

CAS: 64475-85-0

RTECS: PY8240000

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM

SILICA, CRYSTALLINE - CRISTOBALITE

CAS: 14464-46-1

RTECS: VV7325000

OSHA PEL SEE TABLE Z3

ACGIH TLV: 0.05 MG/M3 RDUST9293

SILICA, AMOPHOUS

CAS: 60676-86-0

RTECS: VV7308000

OSHA PEL SEE TABLE Z3

ACGIH TLV: 0.1 MG/M3 RDUST;9293

SILICA, CRYSTALLINE - QUARTZ

CAS: 14808-60-7

RTECS: VV7330000

OSHA PEL SEE TABLE Z3

ACGIH TLV: 0.1 MG/M3 RDUST;9293

TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2100000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO
Health Hazards Acute and Chronic:REPEATED EXPOSURE TO CRYSTALLINE
SILICA MAY CAUSE PNEUMOCONIOSIS,A PROGRESSIVELY DISABLING LUNG
DISEASE. REPORTS HAVE ASSOCIATED PROLONGED AND REPEATED
OCCUPATIONAL OVEREXPOSURE TO SOLVENTS WITH PERMA NENT BRAIN AND
NERVOUS SYSTEM DAMAGE.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:GASTROINTESTINAL IRRITATION, NAUSEA AND
VOMITING. ASPIRATION OF MATERIAL INTO LUNG CAN CAUSE CHEMICAL
PNEUMONITIS WHICH CAN BE FATAL. INHALE-MAY CAUSE NOSE OR THROAT
IRRITATION. EYE-MAY CAUSE EYE IRRI TATION. SKIN-MAY CAUSE DEFATTING
AND IRRITATION OF THE SKIN.
Medical Cond Aggravated by Exposure:PRE-EXISTING RESPIRATORY CONDITIONS
MAY BE AGGRAVATED BY EXPOSURE TO CRYSTALLINE SILICA.

First Aid:SWALLOWED-CALL POISON CONTROL CENTER, HOSPITAL EMERGENCY ROOM
OR MD IMMEDIATELY. INHALED-REMOVE TO FRESH AIR IMMEDIATELY. IF
BREATHING HAS STOPPED, GIVE ARTIFICIAL RESPIRATION. KEEP WARM AND
QUIET. ME D ATTN IMMED. EYE-FLUSH WITH LARGE AMOUNTS OF WATER AT
LEAST 15 MIN. GET MED ATTN. SKIN-REMOVE CONTAMINATED CLOTHING. WASH
AFFECTED AREA WITH SOAP AND WATER. MED ATTN IF IRRIT PERSISTS.

Flash Point:102F - 38.89C
Extinguishing Media:NFPA CLASS B FIRE EXTINGUISHER DESIGNED TO
EXTINGUISH FLAMMABLE LIQUID FIRES. POLYMER FOAM PREFERRED FOR LARGE
FIRES.
Fire Fighting Procedures:WEAR SELF CONTAINED BREATHING APPARATUS. WATER
MAY BE INNEFECTIVE, BUT MAY BE USED TO PREVENT PRESSURE BUILD-UP.
IF WATER IS USED, FOG NOZZLES ARE PREFEREABLE.
Unusual Fire/Explosion Hazard:DURING EMERGENCY CONDITIONS, OVEREXPOSURE
TO DECOMP PRODUCTS MAY CAUSE A HEALTH HAZARD. OBTAIN MED ATTN.KEEP
CONTAINERS CLOSED.ISOLATE FROM HEAT,ELECT EQUIP.

Spill Release Procedures:KEEP SPECTATORS AWAY. ELIM ALL IGNITION
SOURCES. DIKE & CONTN SPILL WITH INERT MATL. TR LQDS TO COV MTL
CNTNR FOR RECOV OR DISP OR REM W/INERT ABSORB. USE NON-SPRKG TOOLS.
PLACE ABSORB MAT IN COV META L CONTNR FOR DISP. PREVENT CONTAM OF
SEW,STRMS,ETC

Handling and Storage Precautions:DO NOT STORE ABOVE 95 DEGREES F. STORE
LARGE QUANTITIES IN COMPLIANCE WITH OSHA 29CFR1910.106.
Other Precautions:DO NOT TAKE INTERNALLY. CLOSE CONTAINER AFTER EACH
USE. DO NOT BREATHER SANDING DUST. DO NOT WASH AND RE-USE
CONTAINERS FOR ANY PURPOSE. DO NOT WELD, BRAZE OR CUT ON EMPTY
CONTAINER. NEVER USE PRESSUR E TO EMPTY.

Respiratory Protection:SPRAYING OUTDOORS OR IN OPEN AREA USE NIOSH
APPROVED MECH FILTER RESPIRATOR TO REMOVE OVERSPRAY. RESTRICTED
AREA, NIOSH APPROVED PAINT SPRAY(CHEMICAL CARTRIDGE/MECHANICAL
FILTER)RESPIRATOR. CONFINED A REA, NIOSH APPROVED AIR-SUPPLIED
RESP.
Ventilation:PROVIDE GENERAL DILUTION & LOCAL EXHAUST VENTILATION. VENT
VAPORS PRODUCED WHILE DRYING OR BAKING THIS PRODUCT.
Protective Gloves:SOLVENT IMPERMEABLE GLOVES
Eye Protection:WEAR SAFETY SPECTACLES.
Other Protective Equipment:NOT LIKELY TO BE NEEDED.
Supplemental Safety and Health
SOLVENT IMPERMEABLE GLOVES ARE REQUIRED FOR REPEATED OR PROLONGED
CONTACT.

HCC:F4
Boiling Pt:B.P. Text:244F - 395F
Vapor Pres:2
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:59

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS OR ALKALINE MATERIALS.
Stability Condition to Avoid:AVOID EXCESSIVE HEAT AND SOURCES OF
IGNITION.
Hazardous Decomposition Products:BURNING, INCLUDING WHEN HEATED BY
WELDING OR CUTTING, WILL PRODUCE SMOKE, CARBON MONOXIDE AND CARBON
DIOXIDE.
Conditions to Avoid Polymerization:KEEP AWAY FROM HEAT, SPARKS AND
FLAME.

Waste Disposal Methods:IAW FED, STATE & LOCAL LAWS. INCINERATE ONLY IN
EPA PERMITTED FACILITY. DO NOT INCINERATE CLOSED CONTAINERS.
OBSERVE PRECAUTIONS FOR DISPOSAL OF FLAMMABLE MATERIALS.
CONTAMINATED ABSORBANT MAY BE DISP OSED IN A HAZARDOUS WASTE
LANDFILL.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.