Product ID:HD3404 HARDENER
MSDS Date:01/01/1985
FSC:8040
NIIN:00-235-8357
Kit Part:Y
MSDS Number: BDLQH

Emergency Phone: (716)372-6300

Cage: DO953

Telephone: 716-372-6300/6309

Cage: DO953

TRIETHYLENETETRAMINE

CAS: 112-24-3

RTECS: YE6650000

Fraction By Weight: UNKN

Effects of Overexposure:COUGHING AND IRRITATION OF NOSE AND
THROAT.REPEATED CONTACT WILL CAUSE SKIN SENSITIZATION,BURNS.

First Aid:CONT. CAUSES EYE INJURY,FLUSH WITH COPIOUS AMOUNTS OF WATER
FOR AT LEAST 15 MIN,CONSULT A PHYSICIAN. IN CASE OF SKIN
CONTACT,WASH IMMEDIATELY WITH SOAP AND WATER.

Flash Point:290F (C.O.C.)
Lower Limits:1.0
Upper Limits:6.5
Extinguishing Media:USE WATER SPRAY,DRY CHEMICAL,ALCOHOL FOAM, OR CO*2.
Fire Fighting Procedures:USE WATER TO KEEP FIRE-EXPOSED CONTAINERS
COOL.
Unusual Fire/Explosion Hazard:CARE MUST BE USE TO PREVENT IGNITION WHEN
PROCESSING OR HANDLING AT TEMPERATURES ABOVE THE FLASH PT.

Spill Release Procedures:IF ODOR BECOMES STRONG ENOUGH TO BE
NOTICEABLE,ONLY PROPERLY PROTECTED PERSONNEL SHOULD REMAIN IN THE
AREA.FLUSH WITH LARGE AMOUNTS OF COLD WATER UNTIL ODOR HAS
DISAPPEARED.FREELY VENTILATE THE AREA T O REMOVE VAPORS

Handling and Storage Precautions:PROTECT FROM PHYSICALDAMAGE.STORE IN
COOL DRY AREA,WELL VENTILATED AREA AWAY FROM ANY AREA WHERE FIRE
HAZARD MAY BE ACUTE
Other Precautions:TETA IS A SKIN SENSITIZER.AVOID SKIN CONTACT.

Respiratory Protection:SCBA IF EXPOSED TO FUMES
Ventilation:MECH(GEN)OR LOCAL EXHAUST THAT PROVIDES ADEQUATE
VENTILATION
Protective Gloves:RUBBER
Eye Protection:GOGGLES/FACE SHIELD
Other Protective Equipment:AS REQUIRED TO PREVENT PROLONGED CONTACT.
Supplemental Safety and Health
MSDS REVISED 3/30/84.THIS ITEM IS PART OF KIT.

HCC:N1
Boiling Pt:B.P. Text:531 F
Vapor Pres:<.1
Vapor Density:5.0
Spec Gravity:0.98
Evaporation Rate & Reference:<0.01 (BU AC =1)
Solubility in Water:COMPLETELY
Appearance and Odor:PALE YELLOW,LOW VISCOSITY LIQUID;MILD AMMONIA ODOR
Percent Volatiles by Volume:NIL

Stability Indicator/Materials to Avoid:YES
AVOID CONTAMINATION WITH STRONG ACIDS.
Stability Condition to Avoid:NONE SPECIFIED BY THE MFR.
Hazardous Decomposition Products:THERMAL DECOMPOSITION MAY PRODUCE
HCN,NO*X,CO AND CO*2.
Conditions to Avoid Polymerization:DO NOT MIX LARGE BATCHES OF EPOXY
RESIN AND TETA.

Waste Disposal Methods:IF WATER IS NOT AVAILABLE OR ITS USE IS
IMPRACTICAL SPILLED TETA MAY BE ABSORBED WITH SODIUM CARBONATE OR
LIME.CONTAMINATED MATERIAL SHOULD BE DISPOSED OF IN ACCORDANCE WITH
LOCAL,STATE AND FEDERAL RE GULATIONS.HD3404 MAY BE A CORROSIVE
W.UN.RCRA

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.