Product ID:PRIMER COATING, EPOXY PART B 09 ID724116
MSDS Date:08/16/1988
FSC:8010
NIIN:00-082-1714
Kit Part:Y
MSDS Number: BHBZQ

PRATT & LAMBERT, INC.-INDUSTRIAL COATINGS DIV.

16116 E 13TH ST
WICHITA, KS 67201
US

Preparer: KAY HATFIELD 67201

Cage: FO127

PRATT AND LAMBERT INC

22 CLEVELAND, OH 44101-1027 US

Telephone: 216-566-2902

Cage: 61196

PHENOL 4.4 (1-METHYL ETHYLIDENE BIS POLY)

CAS: 6810-56-0

OSHA PEL NONE ESTABLISHED

ACGIH TLV: NONE ESTABLISHED

4,4'-ISOPROPYLIDENEDIPHENOL (SARA III)

CAS: 80-05-7

RTECS: SL6300000

DIETHYLENE TRIAMINE

CAS: 111-40-0

RTECS: IE1225000

OSHA PEL 1 PPM

ACGIH TLV: S, 1 PPM; 9192

PROPYLENE GLYCOL MONOMETHYL ETHER

CAS: 107-98-2

RTECS: UB7700000

OSHA PEL 100 PPM/150 STEL

ACGIH TLV: 100 PPM/150STEL;9192

XYLENES (O-,M-,P- ISOMERS) (SARA III)

CAS: 1330-20-7

RTECS: ZE2100000

OSHA PEL 100 PPM/150 STEL

ACGIH TLV: 100 PPM/150STEL;9192

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

ETHYL BENZENE (SARA III)

CAS: 100-41-4

RTECS: DA0700000

OSHA PEL 100 PPM/125 STEL

ACGIH TLV: 100 PPM/125STEL 9192

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

N-BUTYL ALCOHOL (SARA III)

CAS: 71-36-3

RTECS: EO1400000

OSHA PEL 100 PPM

ACGIH TLV: S, C 50 PPM; 9293

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

VOL ORGANIC CMPD 5.8 LB/GL LESS WATER & NPRS* 696 G/L LESS

RTECS: 9999999VO

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO
Health Hazards Acute and Chronic:OVEREXPOSURE TO XYLENE MAY CAUSE
INJURY TO THE LIVER,KIDNEYS AND BLOOD. PROLONGED OVEREXPOSURE TO
SOLVENTS WITH PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.REPEATED
CONTACT MAY CAUSE DERMATITIS.

First Aid:IF SWALLOWED, CALL POISON CONTROL CENTER, HOSPITAL EMERGENCY
ROOM OR MD IMMED.INHALED,REMOVE TO FRESH AIR IMMED.IF BREATHING HAS
STOPPED, GIVE ARTIFICIAL RESPIRATION. KEEP WARM AND QUIET.GET MED
ATTN IMMED. EYE,FLUSH WITH LARGE AMTS OF WATER AT LEAST 15 MIN.GET
MED ATTN IMMED. SKIN,WASH AFFECTED AREA WITH SOAP & WATER.REMOVE
CONTAMINATED CLOTHING.GET MED ATTN IF IRRITATION PERSISTS.

Flash Point:59F - 15.00C
Extinguishing Media:NFPA CLASS B FIRE EXTINGUISHER DESIGNED TO
EXTINGUISH FLAMMABLE LIQUID FIRES. POLYMER FOAM PREFERRED FOR LARGE
FIRES.
Fire Fighting Procedures:WEAR SELF-CONTAINED BREATHING APPARATUS. WATER
MAY BE INEFFECTIVE, BUT MAY BE USED TO PREVENT PRESSURE BUILD-UP.
IF WATER IS USED, FOG NOZZLES ARE PREFERABLE.
Unusual Fire/Explosion Hazard:DURING EMERGENCY CONDITIONS, OVEREXPOSURE
TO DECOMPOSITION PRODUCTS MAY CAUSE A HEALTH HAZARD. OBTAIN MEDICAL
ATTENTION. WARNING! FLAMMABLE.

Spill Release Procedures:KEEP SPECTATORS AWAY. ELIM ALL IGNITION
SOURCES.DIKE & CONTN SPILL WITH INERT MATL.TR LQDS TO COV MTL CNTNR
FOR RECOV OR DISP OR REM W/INERT ABSORB.USE NON-SPRKG TOOLS.PLACE
ABSORB MAT IN COV METAL CO NTNR FOR DISP.PREVENT CONTAM OF SEW,
STRMS, ETC.

Handling and Storage Precautions:DO NOT STORE ABOVE 90 DEGREES F.RCRA
CLASSIFICATION D001.
Other Precautions:DO NOT TAKE INTERNALLY OR BREATH SANDING DUST.CLSE
CONTNR AFTER EA USE.KEEP AWAY FRM CHLDRN. AVD SKIN CONTCT. EMPTY
CONTNR MUST NOT BE WASHED & REUSED FOR ANY PURPOSE.NEVR USE
PRESSURE TO EMPTY.DO NOT WELD, BRAZE OR CUT ON EMPTY CONTNR.

Respiratory Protection:WELL-VENTILATED AREA-NIOSH APPROVED MECH FILTER
RESPIR TO REMOVE OVERSPRAY.RESTRICTED AREA-NIOSH APPROVED PAINT
SPRAY RESPIR.CONFINED AREA-NIOSH APPROVED AIR-SUPPLIED RESPIR.OSHA
29CFR1910/1234 RESP P ROT & RESP PROT MANUAL.
Ventilation:PROVIDE GENERAL DILUTION AND LOCAL EXHAUST VENTILATION.
Protective Gloves:SOLVENT IMPERMEABLE GLOVES.
Eye Protection:WEAR SAFETY SPECTACLES.
Other Protective Equipment:EYEWASH FACILITY, SAFETY SHOWER.
Supplemental Safety and Health
SOLVENT IMPERMEABLE GLOVES ARE REQUIRED FOR REPEATED OR PROLONGED
CONTACT.PART "B" OF TWO PART PRODUCT. SEE P/N IND C FOR PART "A".

Boiling Pt:B.P. Text:243F - 428F
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:81

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS OR ALKALINE MATERIALS. OXIDIZING MATERIALS. ACCELERATORS.
Stability Condition to Avoid:AVOID EXCESSIVE HEAT AND SOURCES OF
IGNITION. HAZARDOUS POLYMERIZATION MAY OCCUR WITH THE ADDITION OF
EXCESS HARDENER.
Hazardous Decomposition Products:BURNING, INCLUDING WHEN HEATED BY WELD
OR CUT,WILL PRODUCE SMOKE,CARBON MONOXIDE AND CARBON DIOXIDE.
Conditions to Avoid Polymerization:KEEP AWAY FROM HEAT,SPARKS AND
FLAME.

Waste Disposal Methods:IAW FED,STATE & LOCAL LAWS. INCINERATE ONLY IN
EPA PERMITTED FACILITY. DO NOT INCINERATE CLOSED CONTAINERS.OBSERVE
PRECAUTIONS FOR DISPOSAL OF FLAMMABLE MATERIALS.CONTAMINATED
ABSORBANT MAY BE DISPOSE D IN A HAZARDOUS WASTE LANDFILL.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.