Product ID:EASTMAN 910 THT ADHESIVE
MSDS Date:01/01/1985
FSC:8040
NIIN:00K000902
MSDS Number: BCBSB

Emergency Phone: 716-722-5151

Cage: 19139

Telephone: 716-722-5151/(800) 242-2424

Cage: 19139

ALKENYL CYANOACRYLATE

Fraction By Weight: 100%

Effects of Overexposure:SKIN:POLYMERIZATION OCCURS & BONDS SKIN
V.RAPIDLY;EYES:CANBOND EYELIDS;VAP MAY IRRIT MUCUS MEMBRANE

First Aid:SKIN:FLUSH IMMED W/H*2O TO CAUSE POLYMERIZATION OF THE
MONOMER & REDUCE ITS AFFINITY FOR THE SKIN;EYES:IRRIGATE IMMED &
THOROUGHLY W/H*2O HOLDING THE LIDS APART TO PREVENT BONDING.DO NOT
FORCE APART I F BONDED.SEE A PHYSICAIAN;INH:REMOVE FROM EXPOSURE

Flash Point:UNK(COMBUSTIBLE)
Lower Limits:UNK
Upper Limits:UNK
Extinguishing Media:CO*2,DRY CHEM;WATER SPRAY IF POLYMERIZATION NOT
HAZARDOUS.
Unusual Fire/Explosion Hazard:NONE KNOWN

Spill Release Procedures:ELIM IGNITION SOURCES.SOAK UP ON
CLOTHS/ABSORBENT MATL.INCINERATE IMMEDIATLY OR STORE IN A CLOSED
METAL CONTAINER.PROTECT EYES,SKIN & CLOTHING BEFORE CLEAN-UP IAW
FED,STATE & LOCAL REGULATIONS.

Handling and Storage Precautions:STORE IN TIGHTLY CLOSED CONTAINERS IN
VENTILATED/DRY AREA.AVOID WATER/MOISTURE CONTACT W/MATL
CONTNRS.AVOID SKIN,EYES & CLOTHING CONTACT.
Other Precautions:USE W/VENTILATION ADEQUATE TO MAINTAIN ATMOSPHERE
CONCENTRATION OF VA BELOW IRRITATING LEVEL.IF SKIN BONDNG
OCCURD,SOAK IN WARMWATER TO ENHANCE/LOOSENING OF THE BOND.KEEP AWAY
FM HEAT/FLAME.

Respiratory Protection:A NIOSH APPRVD RESP FOR ORGANIC VAP IF NEEDED;NO
NEED IN NORAMLCOND.
Ventilation:LOCAL EXHAUST/MECHANICAL(GEN) RECOMMENDED BY MFR.
Protective Gloves:POLYETHLN/RUBBR
Eye Protection:SAFETY GOGGLES/GLASSES.
Other Protective Equipment:AS NEEDED BY LOCAL AUTHORITIES.
Supplemental Safety and Health
MFR MSDS 3/30/73.PROD SOLD TO PERMA-BOND 8/80.PER PERMA-BOND 1/18/84 NO
MULTIPLE HAZARDS EXIST.STORE WITH OTHER COMBUSTIBLES.STG CDE BASED
ON FLASH PT OF OTHER 910 PRODUCTS.

HCC:V4
Boiling Pt:B.P. Text:APPROX 176F
Vapor Pres:UNK
Vapor Density:UNK
Spec Gravity:UNK
Evaporation Rate & Reference:CLEAR LIQUID
Solubility in Water:INSOLUBLE
Percent Volatiles by Volume:UNK

Stability Indicator/Materials to Avoid:NO
OXIDIZING MATL CAN CAUSE A VIGOROUS REACTION
Stability Condition to Avoid:POLYMERIZATION OCCURES BY
WATER/MOISTURE.MAY BE EXOTHERMIC.
Hazardous Decomposition Products:CO,CO*2,OXIDES OF NITROGEN.
Conditions to Avoid Polymerization:MANY COMMON MATLS SUCH AS H*2O CAN
POLYMERIZE EXOTHERMALLY.

Waste Disposal Methods:INCINERATION OR LANDFILL.MFR SUGGESTED
INCINERATE WASTE.OBSERVE ALL FEDERAL,STATE & LOCAL LAWS CONCERNING
HEALTH & POLLUTION.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.