Product ID:EPOCAST RESIN 200
MSDS Date:01/01/1985
FSC:8030
NIIN:00K001338
MSDS Number: BCCSN

Emergency Phone: 213-247-6210

Cage: GO767

Telephone: 818-247-6210/800-873-1138

Cage: GO767

BIS PHENOL EPOXY RESIN;TLV UNKNOWN, BUT SPI ERF HAZARD

Fraction By Weight: 100%

Effects of Overexposure:EFFECTS NOT NOTED, BUT AVOID EYE CONTACT,
INGEST, OR SKIN CONTACT.

First Aid:INHALE:REMOVE TO FRESH AIR, GIVE CPR/O*2 IF
NEED;EYES/SKIN:FLUSH W LG AMTS H*2O FOR 15 MIN;INGEST:RINSE MOUTH,
GET MEDICAL ATTENTION(HIGH POLYMER INSOLUBLE IN BODY FLUIDS, PER
MFG);MFG SUGGESTS USE DE NATURED ALCOHOL TO REMOVE FROM SKIN,THEN
WASH.

Flash Point:>400F,>204C(COC)
Extinguishing Media:H*2O,FOAM, OR DRY CHEMICAL POWDER.
Fire Fighting Procedures:WEAR SELF-CNTD BRTHG APP H*20 SPRAY TO COOL
CONTR.
Unusual Fire/Explosion Hazard:MATL MAY/MAY NOT BURN. CONTAINER MAY
EXPLODE IN HEAT OF FIRE.FIRE MAY YIELD TOXIC GASES.

Spill Release Procedures:EVACUATE UNPROTECTED PERSONS. ELIM IGNITION
SOURCES. STOP LEAK. H*2O SPRAY COOL CONT/DIVERT SPILL FROM
FIRE/HEAT. PROVIDE VENTILATION. ABSORB W COMMERCIAL
ABSORBENT,SHOVEL INTO METAL DRUMS:LG SPILL:DI KE W COMMERCIAL
ABSORBENT,PUMP INTO COVERED DRUMS.

Handling and Storage Precautions:STORE IN COOL,DRY,WELL VENT,LOW FIRE
RISK AREA. PROTECT FROM PHYSICAL DAMAGE.AVOID ANY PHYSICAL CONTACT.
KEEP CONTAINERS TIGHTLY CLOSED.
Other Precautions:MAINTAIN STRICT HYGIENE, AVOID PHYSICAL CONTACT,
REMOVE & WASH CONTAMINATED CLOTHING. MFG SUGGESTS USE OF PROTECTIVE
SKIN CREAMS. EXHAUST CURING OVENS TO OPEN AIR. AVOID TEMP ABOVE
150-180F.

Respiratory Protection:NONE SHOULD BE NEEDED
Ventilation:MECHANICAL (GENERAL/LOCAL EXHAUST)
Protective Gloves:PV/RUBBER
Eye Protection:SAFETY/CHEM GOGGLES
Other Protective Equipment:FULL WORK CLOTHING TO PREVENT REPEATED OR
PROLONGED CONTACT.
Supplemental Safety and Health

HCC:N1
Spec Gravity:1.5
Solubility in Water:NEGLIGIBLE
Appearance and Odor:TAN PASTE; SLIGHT ETHERAL ODOR
Percent Volatiles by Volume:0

Stability Indicator/Materials to Avoid:NO
Stability Condition to Avoid:TEMP >150F WILL START EXOTHERMIC REACTION
WITH FILLER.
Hazardous Decomposition Products:NONE NOTED, BUT EXPECT CO, CO*2, H*2O.
Conditions to Avoid Polymerization:DO NOT HEAT ABOVE 150F WITHOUT
ADDITION OF HARDENER.

Waste Disposal Methods:KEEP IN COVERED CONTAINERS PENDING DISPOSAL.
HANDLE AND DISPOSE IN FULL COMPLIANCE WITH ALL APPLICABLE
INTERNATIONAL,FEDERAL,STATE AND LOCAL REGULATIONS. MFG SUGGESTS
INCINERATION OR BURY IN APPROVED LANDFILL, AFTER ABSORBING W
SAND;WASH RESIDUE.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.