BFCGP - EPOXO 2000XA,DARK GRAY,36076,PART A

  • MSDS: BFCGP
  • Manufacturer: AMERICAN ABRASIVE METALS CO
  • Product Name: EPOXO 2000XA,DARK GRAY,36076,PART A
  • National Stock Number: 5610-00-516-0038
Product Identification

Product ID:EPOXO 2000XA,DARK GRAY,36076,PART A
MSDS Date:01/01/1987
FSC:5610
NIIN:00-516-0038
Kit Part:Y
MSDS Number: BFCGP

Responsible Party
AMERICAN ABRASIVE METALS CO
460 COIT ST
IRVINGTON, NJ 07111-4607
US

Cage: 88444

Contractor
AMERICAN SAFETY TECHNOLOGIES INC
ROSELAND, NJ 07068 US

Telephone: 973-403-2600

Cage: 88444

Ingredients

EPOXY RESINS CAS# 25068-38-6

CAS: 25068-38-6

RTECS: KC2100000


XYLENES (O-,M-,P- ISOMERS) (SARA III)

CAS: 1330-20-7

RTECS: ZE2100000

OSHA PEL 100 PPM/150 STEL

ACGIH TLV: 100 PPM/150STEL;9192

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS


PROPYLENE GLYCOL MONOMETHYL ETHER

CAS: 107-98-2

RTECS: UB7700000

Fraction By Weight: 1%

OSHA PEL 100 PPM/150 STEL

ACGIH TLV: 100 PPM/150STEL;9192


SILICA, CRYSTALLINE - QUARTZ

CAS: 14808-60-7

RTECS: VV7330000

Fraction By Weight: 30%

OSHA PEL SEE TABLE Z3

ACGIH TLV: 0.1 MG/M3 RDUST;9293

Hazards

Effects of
Overexposure:INHAL:DIZZ,UNCON.SKIN:IRRIT,SENSIT.EYE:IRRIT,DAMAGE.

First Aid

First Aid:EYE:FLUSH W/ LG AMT OF WATER.CALL MD.INHAL:FRESH
AIR,O*2,ARTIF RESPIR.SKIN:WASH W/ SOAP & WATER.INGEST;DO NOT INDUCE
VOMITING.CALL MD.

Fire Fighting

Flash Point:81F,27C PMCC
Lower Limits:1
Upper Limits:12
Extinguishing Media:CHEMICAL FOAM OR DRY CHEMICAL.
Fire Fighting Procedures:USE SCBA W/ FULL FACE PIECE
Unusual Fire/Explosion Hazard:VAPORS MAY TRAVEL ALONG GROUND TO
IGNITION SOURCES.

Accidental Release

Spill Release Procedures:ELIMINATE ALL IGNITION
SOURCES(FLAMES,FLARES,PILOT LIGHTS,ELECTRICAL SPARKS.ABSORB ON
SAND,CLAY OR OTHER ABSORBENT MATERIAL AND SHOVEL INTO CONTAINERS.

Handling

Handling and Storage Precautions:DO NOT GET INTO EYES.AVOID CONTACT W/
SKIN & CLOTHING.AVOID INHAL OF VAP/MIST.USE W/ ADEQUATE VENT.WASH
AFTER HANDLING.REMOVE,WASH CONTAM CLOTHING.
Other Precautions:WHEN REMOVING OLD COATING BY
SANDING,SANDBLASTING,WEAR PROPER DUST MASKS TO AVOID INHAL SILICA
DUST.AVOID EXTREME HEAT.DO NOT EXCEED 100F IN STORAGE AREA.KEEP
AWAY FROM FLAME.

Exposure Controls

Ventilation:LOCAL EXHAUST,MECHANICAL VENT TO KEEP BELOW TLV.
Protective Gloves:RUBBER,BUNAN
Eye Protection:CHEM SPLASH GOGGLES
Other Protective Equipment:PROTECTIVE CLOTHING
Supplemental Safety and Health
MSDS PREP: 86302. PART A OF A 2-PART KIT. KEY1:F4.

Chemical Properties

HCC:F4
Boiling Pt:B.P. Text:>240F,>116C
Vapor Pres:8
Vapor Density:3.7
Spec Gravity:1.7
Evaporation Rate & Reference:0.7(BUAC=1)
Solubility in Water:SLIGHT
Appearance and Odor:VISCOUS PASTE,MILD ODOR

Stability

Stability Indicator/Materials to Avoid:YES
STRONG ACID,ALKALIES,AMINES,OXIDIZING AGENTS
Hazardous Decomposition Products:CO,CO*2,TOXIC FUMES WHEN BURNING

Disposal

Waste Disposal Methods:DISPOSE BY CONTROLLED BURNING OR AUTHORIZED
LANDFILL IN ACCORDANCE W/ LOCAL,STATE AND FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.