Product ID:DELTRON GLOSS ADDITIVE
MSDS Date:03/04/1991
FSC:9390
NIIN:00B160020
MSDS Number: BKBHX

PPG INDUSTRIES, INC.

4325 ROSANNA DRIVE
ALLISON PARK, PA 15101
US

Emergency Phone: (304) 843-1300

Info Phone: (412) 492-5555

Cage: DO894

PPG INDUSTRIES, INC.

9 ALLISON PARK, PA 15101 US

Telephone: 412-592-5555

Cage: DO894

METHYL N-AMYL KETONE

CAS: 110-43-0

Fraction By Weight: 10%

TOLUENE

CAS: 108-88-3

Fraction By Weight: 30%

OSHA PEL 200 PPM/150 STEL

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

XYLENE

CAS: 1330-20-7

Fraction By Weight: 5%

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

FILM FORMERS, RESINS, AND ADDITIVES

Fraction By Weight: 65%

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:ACUTE: EYE AND SKIN IRRITATION MAY
OCCUR. CHRONIC: HARMFUL OR FATAL IF SWALLOWED.
Explanation of Carcinogenicity:NONE SPECIFIED BY MANUFACTURER.
Effects of Overexposure:EYE WATERING, HEADACHES, NAUSEA, DIZZINESS, AND
LOSS OF COORDINATION ARE INDICATIONS THAT SOLVENT LEVELS ARE TOO
HIGH. REDNESS, ITCHING, BURNING SENSATION AND VISUAL DISTURBANCES
MAY INDICATE EXCESSIV E EYE CONTACT.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INGESTION: IF SWALLOWED GIVE 1 OR 2 GLASSES OF WATER, DO NOT
INDUCE VOMITING. EYES: FLUSH EYES IMMEDIATELY FOR 15 MIN. SKIN:
REMOVE BY WIPING, FOLLOWED BY WATERLESS HAND CLEANER AND SOAP AND
WATER. IN HALATION: IF AFFECTED BY INHALATION OF OR SPRAY MIST,
REMOVE TO FRESH AIR. APPLY ARTIFICIAL RESPIRATION.

Flash Point Method:PMCC
Flash Point:45.0F,7.2C
Lower Limits:1.2
Extinguishing Media:USE NFPA CLASS B EXTINGUISHERS (CARBON DIOXIDE, DRY
CHEMICAL OR UNIVERSAL AQUEOUS FILM FORMING FOAM).
Fire Fighting Procedures:WATER SPRAY MAY BE INEFFECTIVE BUT USEFUL TO
COOL CONTAINERS AND PREVENT PRESSURE BUILD-UP. IF WATER IS USED,
FOG NOZZLES ARE PREFERRABLE.
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE WHEN
EXPOSED TO EXTREME HEAT. DO NOT APPLY ON HOT SURFACES. TOXIC GASES
MAY FORM WHEN PRODUCT IS CONTACTED BY FLAME OR HEAT.

Spill Release Procedures:PROVIDE MAXIMUM VENTILATION. ONLY PERSONNEL
WITH PROPER RESPIRATORY AND SKIN AND EYE PROTECTION SHULD BE
PERMITTED IN THE AREA. REMOVE ALL IGNITION SOURCES. TAKE UP SPILLED
MATERIAL W/SAWDUST, VERMICU LITE, OR OTHER ABSORBENT MATERIAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LARGE
QUANTITIES IN BUILDINGS DESIGNED AND PROTECTED FOR STORAGE OF NFPA
CLASS IB FLAMMABLE LIQUIDS.
Other Precautions:CONTAINERS SHOULD BE GROUNDED WHEN POURING. AVOID
FREE FALL OF LIQUIDS IN EXCESS OF A FEW INCHES

Respiratory Protection:OVEREXPOSURE TO VAPORS MAY BE PREVENTED BY
ENSURING VENTILATION CONTROLS, VAPOR EXHAUST OR FRESH AIR ENTRY.
NIOSH/ MSHA-APPROVED PAINT SPRAY OR AIR SUPPLIED RESPIRATORS MAY
ALSO REDUCE EXPOSURE.
Ventilation:GENERAL DILUTION/LOCAL EXHAUST VENTILATION IN VOLUME TO
KEEP THE CONCENTRATION OF INGREDIENTS BELOW SUGGESTED EXPOSURE.
Protective Gloves:POLYVINYL ALCOHOL, LATEX/NITRILE RUBBER.
Eye Protection:CHEMICAL SPLASH GOGGLES OR FACE SHIELD.
Other Protective Equipment:CLEAN OR DISCARD CONTAMINATED CLOTHING.
Work Hygienic Practices:STANDARD PERSONAL HYGIENE.
Supplemental Safety and Health
IF ANY OF THE FOLLOWING OCCUR DURING OR FOLLOWING USE OF THIS PRODUCT,
CONTACT A POISON CONTROL CENTER, EMERGENCY ROOM OR PHYSICIAN
IMMEDIATELY (HAVE MSDS SHEET AVAILABLE); INGESTION, EXCESSIVE
EXPOSU RE TO A CORROSIVE MATERIAL, PERSISTENT SKIN/EYE IRRITATION
OR BREATHING DIFFICULTIES.

HCC:F3
Boiling Pt:B.P. Text:230F,110C
Vapor Pres:17.8MMHG
Spec Gravity:.97
Evaporation Rate & Reference:193
Solubility in Water:NEGLIGIBLE
Appearance and Odor:VISCOUS LIQUID WITH AN ODOR CHARACTERISTIC OF THE
SOLVENTS LISTED IN SECTION 2.

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS, OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:HIGH HEAT, OPEN FLAMES AND OTHER SOURCES
OF IGNITION
Hazardous Decomposition Products:WELDING, BRAZING OR FLAME-CUTTING ON
SURFACES COATED WITH THIS PRODUCT MAY PRODUCE FUMES INCLUDING:
CARBON MONOXIDE.

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE, PROVINCIAL AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WASTE MANAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.