Product ID:STARPLUS
MSDS Date:03/04/1991
FSC:9390
NIIN:00B160021
MSDS Number: BKBHY

PPG INDUSTRIES, INC.

4325 ROSANNA DRIVE
ALLISON PARK, PA 15101
US

Emergency Phone: (304) 843-1300

Info Phone: (412) 492-5555

Cage: DO894

PPG INDUSTRIES, INC.

9 ALLISON PARK, PA 15101 US

Telephone: 412-592-5555

Cage: DO894

FILM FORMERS, RESINS, AND ADDITIVES

Fraction By Weight: 65%

METHYL N-AMYL KETONE

CAS: 110-43-0

Fraction By Weight: 10%

TOLUENE

CAS: 108-88-3

Fraction By Weight: 30%

OSHA PEL 200 PPM/150 STEL

ACGIH TLV: 50 PPM; 9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

XYLENE

CAS: 1330-20-7

Fraction By Weight: 5%

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:ACUTE: MODERATE EYE AND SKIN
IRRITATION. CHRONIC: HARMFUL OR FATAL IF SWALLOWED. VAPOR AND SPRAY
MIST MAY BE HARMFUL IF INHALED. REPEATED EXPOSURE TO HIGH VAPOR
CONCENTRATIONS MAY CAUSE IRRITATION OF THE RESPIRATORY SYSTEM AND
PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE.
Effects of Overexposure:EYE WATERING, HEADACHES, NAUSEA, DIZZINESS, AND
LOSS OF COORDINATION ARE INDICATIONS THAT SOLVENT LEVELS ARE TOO
HIGH. REDNESS ITCHING, BURNING SENSATION AND VISUAL DISTURBANCES
MAY INDICATE EXCESSIVE EYE CONTACT.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INGESTION: IF SWALLOWED, GIVE 1 OR 2 GLASSES OF WATER, DO NOT
INDUCE VOMITING. EYES: FLUSH EYES IMMEDIATELY WITH WATER FOR AT
LEAST 15 MINUTES. SKIN: REMOVE PROMPTLY BY WIPING. FOLLOWED BY
WATERLESS H AND CLEANER AND SOAP AND WATER. INHALATION: REMOVE TO
FRESH AIR. APPLY ARTIFICIAL RESPIRATION AND OTHER SUPPORTIVE
MEASURES AS REQUIRED.

Flash Point Method:PMCC
Flash Point:45.0F,7.2C
Lower Limits:1.2
Extinguishing Media:USE NFPA CLASS B EXTINGUISHERS (CARBON DIOXIDE, DRY
CHEMICAL, OR UNIVERSAL AQUEOUS FILM FORMING FOAM).
Fire Fighting Procedures:WATER SPRAY MAY BE INEFFECTIVE BUT MAY BE USED
TO COOL CONTAINERS TO PREVENT PRESSURE BUILD-UP AND POSSIBLE
AUTOIGNITION OR EXPLOSION. WEAR SCBA.
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE WHEN
EXPOSED TO EXTREME HEAT. TOXIC GASES MAY FORM WHEN PRODUCT IS
CONTACTED BY FLAME OR HOT SURFACES.

Spill Release Procedures:PROVIDE MAXIMUM VENTILATION. ONLY PERSONNEL
EQUIPPED WITH PROPER RESPIRATORY, SKIN AND EYE PROTECTION SHOULD BE
PERMITTED IN THE AREA. REMOVE ALL SOURCES OF IGNITION. TAKE UP
SPILLED MATERIAL WITH SAW DUST, VERMICULITE, OR OTHER ABSORBENT
MATERIAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LARGE
QUANTITIES IN BUILDINGS DESIGNED AND PROTECTED FOR STORAGE OF NFPA
CLASS IB FLAMMABLE LIQUIDS.
Other Precautions:CONTAINERS SHOULD BE GROUNDED WHEN POURING. AVOID
FREE FALL OF LIQUIDS IN EXCESS OF A FEW INCHES.

Respiratory Protection:VAPOR EXHAUST OR FRESH AIR ENTRY. NIOSH/MSHA-
APPROVED PAINT SPRAY OR AIR SUPPLIED RESPIRATORS MAY ALSO REDUCE
EXPOSURE. READ RESPIRATOR MANUFACTURER'S INSTRUCTIONS AND
LITERATURE CAREFULLY FOR HOW IT IS TO BE PROPERLY FILTERED.
Ventilation:GENERAL DILUTOIN OR LOCAL EXHAUST TO KEEP THE CONCENTRATION
BELOW THE LOWEST SUGGESTED EXPOSURE.
Protective Gloves:POLYVINYL ALCOHOL, LATEX/NITRILE RUBBER.
Eye Protection:CHEMICAL SPLASH GOGGLES OR FULL FACE.
Other Protective Equipment:CLEAN OR DISCARD CONTAMINATED CLOTHING AND
SHOES.
Work Hygienic Practices:GENERAL PERSONAL HYGIENE.
Supplemental Safety and Health
CONTAINERS SHOULD BE GROUNDED WHEN POURING. AVOID FREE FALL OF LIQUIDS
IN EXCESS OF A FEW INCHES.

HCC:F3
Boiling Pt:B.P. Text:230F,110C
Vapor Pres:17.8MMHG
Evaporation Rate & Reference:193
Solubility in Water:NEGLIGIBLE
Appearance and Odor:VISCOUS LIQUID WITH AN ODOR CHARACTERISTIC OF THE
SOLVENTS LISTED IN SECTION 2.
Percent Volatiles by Volume:42.30

Stability Indicator/Materials to Avoid:YES
STRONG ALKALIES, STRONG MINERAL ACIDS, OR STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:HIGH HEAT, OPEN FLAMES AND OTHER SOURCES
OF IGNITION
Hazardous Decomposition Products:WELDING BRAZING OR FLAME-CUTTING ON
SURFACES COATED WITH THIS PRODUCT MAY PRODUCE FUMES INCLUDING:
CARBON MONOXIDE.
Conditions to Avoid Polymerization:EXTREME HEAT, FLAMES.

Waste Disposal Methods:MUST BE DISPOSED OF IN ACCORDANCE WITH FEDERAL,
STATE, PROVINCIAL, AND LOCAL ENVIRONMENTAL CONTROL REGULATIONS.
EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF THROUGH AN
APPROVED WASTE MANAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.