Product ID:EASY FLO 3
MSDS Date:01/01/1987
FSC:3455
NIIN:00-019-4328
MSDS Number: BKBJJ

HANDY AND HARTMAN

850 THIRD AVE
NEW YORK, NY 10022-6222
US

Emergency Phone: 212-752-3400

Info Phone: 212-752-3400

Cage: JO825

OHIO METAL WORKING PRODUCTS CO

CANTON, OH 44705 US

Telephone: 216-453-8438

Cage: 0BZR8

SILVER (SARA III)

CAS: 7440-22-4

RTECS: VW3500000

Fraction By Weight: 50%

OSHA PEL 0.01 MG/M3

ACGIH TLV: 0.1 MG/M3; 9192

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

COPPER (SARA III)

CAS: 7440-50-8

RTECS: GL5325000

Fraction By Weight: 15.5%

OSHA PEL 0.1MG/M3 FUME/1 DUST

ACGIH TLV: 0.2MG/M3 FUME; 9192

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

ZINC (SARA III)

CAS: 7440-66-6

RTECS: ZG8600000

Fraction By Weight: 15.5%

OSHA PEL 10 MG ZNO/M3

ACGIH TLV: 10 MG ZNO/M3; 9192

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

CADMIUM (SARA III)

CAS: 7440-43-9

RTECS: EU9800000

Fraction By Weight: 16%

OSHA PEL SEE 1910.1027

ACGIH TLV: 0.01 MG/M3 DUST;9394

EPA Report Quantity: 10 LBS

DOT Report Quantity: 10 LBS

NICKEL (SARA III)

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: 3%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3; 9192

Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:SHORT TERM EXPOSURE TO GRINDING DUST,
OR GASES MAY RESULT IN DISCOMFORT SUCH AS DIZZINESS, NAUSEA,
FEVER, DRYNESS AND/OR IRRITATION OF NOSE, THROAT AND EYES. SKIN
SENSITIVITY MAY ALSO BE NOTED. ACUTE EXPOSURE TO DUST MAY CAUSE
PULMONARY PROBLEMS.
Explanation of Carcinogenicity:CR(VI),CD & NI ARE CONSIDERED
CARCINOGENS UNDER NTP & IARC. RESPIRATORY CANCER FROM
WELDING/GRINDING IS UNCONFIRMED.
Effects of Overexposure:DIZZINESS, NAUSEA, FEVER, DRYNESS AND/OR
IRRITATION OF NOSE, THROAT AND EYES. SKIN SENSITIVITY MAY ALSO BE
NOTED. WATERY EYES, HEADACHE, BREATHING DIFFICULTY, FREQUENT
COUGHING AND/OR CHEST PAINS MAY OCCUR FROM ACUTE EXPOSURE.
Medical Cond Aggravated by Exposure:SOME WORKERS MAY BE AFFECTED BY A
PRE-EXISTING CONDITION OR OTHER OCCUPATIONAL ILLNESS BECAUSE OF THE
WIDE VARIATION IN INDIVIDUAL SUSCEPTIBILITIES.

First Aid:IN CASE OF ELECTRICAL SHOCK, TURN OFF POWER PRIOR TO REMOVAL
FROM EXPOSURE AREA AND ADMINISTRATION OF FIRST AID. CALL FOR
MEDICAL AID. IF NOT BREATHING, BEGIN ARTIFICIAL RESPIRATION/OXYGEN.
EYE:FLUSH WITH WATER FOR 15 MIN AND SEEK MEDICAL HELP. SKIN:WASH
WITH SOAP AND WATER.

Extinguishing Media:NONE
Fire Fighting Procedures:WEAR FIRE FIGHTING PROTECTIVE EQUIPMENT AND A
FULL FACED SELF CONTAINED BREATHING APPARATUS. EVACUATE AREA. COOL
FIRE EXPOSED CONTAINERS WITH WATER SPRAY.

Spill Release Procedures:CLEAN UP ANY GRINDING DUST OR WASTE RESIDUES
AND PLACE IN SUITABLE DOT APPROVED CONTAINERS AND DISPOSE OF IN
FULL COMPLIANCE WITH FEDERAL, STATE AND LOCAL REGULATIONS. AVOID
INHALATION AND SKIN EXPOSU RE.

Handling and Storage Precautions:WEAR GLOVES AND FLAME RETARDANT
CLOTHING WHEN CUTTING, GRINDING OR WELDING. DO NOT EXPOSE SKIN TO
RADIATION WHEN HOT CUTTING OR WELDING.
Other Precautions:PROVIDE PROTECTIVE SCREENS TO SHIELD OTHERS. WHEN
ELECTRODES AND FLUXES ARE CONSUMED, THE FUME AND GAS DECOMPOSITION
PRODUCTS GENERATED ARE DIFFERENT IN FORM FROM THE INGREDIENTS
LISTED. AVOID BREATHI NG DUST. WEAR DUST MASK WHILE GTRINDING.

Respiratory Protection:USE DUST RESPIRATOR OR AIR SUPPLIED RESPIRATOR
WHEN CUTTING, GRINDING OR WELDING IN A CONFINED SPACE OR WHERE
LOCAL EXHAUST OR GENERAL VENTILATION DOES NOT KEEP EXPOSURE BELOW
RECOMMENDED LIMITS. USE ONLY NIOSH APPROVED RESPIRATORS.
Ventilation:USE ENOUGH VENTILATION WHEN CUTTING, GRINDING OR WELDING TO
KEEP THE DUST, FUMES & GASES FROM THE WORKERS BREATHING ZONE
Protective Gloves:LEATHER GLOVES
Eye Protection:OSHA APPROVED GOGGLES/FACE SHIELD W/LENS
Other Protective Equipment:FLAME RETARDANT CLOTHING WHEN CUTTING,
GRINDING OR WELDING. DO NOT EXPOSE SKIN TO RADIATION WHEN HOT
CUTTING OR WELDING.
Work Hygienic Practices:WASH THOROUGHLY BEFORE EATING OR SMOKING.
LAUNDER CONTAMINATIED CLOTHING BEFORE REUSE.
Supplemental Safety and Health
BRAZING MATERIAL IS USED BY OHIO METAL WORKING PRODUCT CO. TO BRAZE
TUNGSTEN CARBIDE (SEE SAME NSN, CAGE 0BZR8).

HCC:N1
Spec Gravity:9.52
Appearance and Odor:METALLIC ROD, WIRE, STRIP, OR POWDER.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, ACIDS AND BASES.
Stability Condition to Avoid:NONE
Hazardous Decomposition Products:NONE

Waste Disposal Methods:DISPOSE I/A/W FEDERAL, STATE & LOCAL REGULATIONS

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.