Product ID:UNSATURATED POLYESTER RESIN
MSDS Date:10/01/1988
FSC:8040
NIIN:00N014044
MSDS Number: BKBTN

ADVANCE COATINGS COMPANY

DEPOT ROAD
WESTMINSTER, MA 01473
US

Emergency Phone: 508-874-5921

Info Phone: 508-874-5921

Cage: 3K491

ADVANCE COATINGS CO

WESTMINSTER, MA 01473 US

Telephone: 978-874-5921

Cage: 3K491

POLYESTER RESINS

Fraction By Weight: 60%

STYRENE, MONOMER (SARA III)

CAS: 100-42-5

RTECS: WL3675000

Fraction By Weight: 40%

OSHA PEL 100 PPM

ACGIH TLV: S,50PPM/100STEL;9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:SKIN, EYE AND NASAL IRRITATION, RED
SKIN.
Explanation of Carcinogenicity:STYRENE: IARC 2B.
Effects of Overexposure:NONE SPECIFIED BY MANUFACTURER.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:REMOVE TO FRESH AIR, REST, KEEP WARM AND GET MD. IF BREATHING
STOPS, ARTIFICIAL RESPIRATION SHOULD BE ADMINISTERED. EYE: FLUSH
WITH WATER FOR AT LEAST 15 MINUTES AND GET MD. INGEST: CALL MD
IMMEDIATEL Y .

Flash Point Method:TCC
Flash Point:94.0F,34.4C
Lower Limits:1.1
Upper Limits:0.1
Extinguishing Media:CARBON DIOXIDE, WATER FOG, WATER FOAM, DRY
CHEMICAL.
Fire Fighting Procedures:NIOSH/MSHA APPROVED SCBA SHOULD BE WORN. FLASH
POINT PENSKY MARTENS TESTER IS 88F.
Unusual Fire/Explosion Hazard:RESIN SPRAY FROM SPRAY GUN IS MORE
FLAMMABLE THAN LIQUID RESIN. DRUMS OF RESIN IF HEATED IN A FIRE MAY
POLYMERIZE AND BUILD UP MORE INTERNAL HEAT.

Spill Release Procedures:ABSORB RESIN WITH VERMICULITE, SAWDUST OR
RAGS, SCOOP UP WITH SCOOPS OR SHOVELS, CLEAN UP RESIDUE WITH STRONG
DETERGENT WATER SOLUTIONS (GLOVES & GOGGLES).
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE RESINS & GELCOATS AWAY FROM HEAT
& LIGHT (NOT OVER 75F). ALWAYS USE UP OLDEST LOTS OF RESIN &
GELCOATS FIRST.
Other Precautions:MATERIALS SHOULD LAST AT LEAST 6 MONTHS AT NOT OVER
75F. STORE IN TIGHTLY CLOSED CANS OR DRUMS OR TANKS. RESIN STORED
GLASS CONTAINERS EXPOSED TO LIGHT WILL GEL PREMATURELY.

Respiratory Protection:NIOSH/MSHA APPROVED ORGANIC VAPOR RESPIRATORS IF
TLV OF STYRENE IS EXCEEDED TO MAINTAIN VAPOR CONCENTRATION OF
STYRENE BELOW 50 PPM TLV.
Ventilation:NONE SPECIFIED BY MANUFACTURER.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:RESPIRATORS & LOCAL EXHAUST ARE MANDATORY
AROUND SPRAY OPERATIONS.
Work Hygienic Practices:WASH THOROUGHLY AFTER USE AND BEFORE EATING,
DRINKING, SMOKING OR USING SANITARY FACILITIES .
Supplemental Safety and Health
CNDTNS (POLYM): AND COULD IGNITE ITSELF. IF NECESSARY, DUMP ON GROUND
AWAY FROM BUILDING.

HCC:F4
Boiling Pt:B.P. Text:293F,145C
Vapor Pres:4.5
Vapor Density:3.6
Spec Gravity:1.12
Solubility in Water:NEGLIGIBLE
Appearance and Odor:VISCOUS LIQUID, WITH ODOR OF STYRENE MONOMER.
Percent Volatiles by Volume:40

Stability Indicator/Materials to Avoid:YES
NEVER MIX ORGANIC PEROXIDES WITH PROMOTERS OR ACCELERATORS. THESE MUST
BE ADDED TO THE RESIN SEPARATELY.
Stability Condition to Avoid:AVOID STORAGE AT OVER 75F. THIS MAY CAUSE
PREMATURE GELATION.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

Waste Disposal Methods:BURNING. DISPOSE IN ACCORDANCE WITH FEDERAL,
STATE AND LOCAL REGULATIONS .

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.