Product ID:THERMOPLASTIC RUBBER, 9201-65-W900
MSDS Date:12/01/1990
FSC:9320
NIIN:00N016395
MSDS Number: BLBQH

ADVANCED ELASTOMER SYSTEMS

540 MARYVILLE CENTRE DR
ST LOUIS, MO 63166-6735
US

Emergency Phone: 314-694-1000

Info Phone: 314-694-1000

Cage: 41599

ADVANCED ELASTOMER SYSTEMS

ST LOUIS, MO 63166-6735 US

Telephone: 314-694-1000

Cage: 41599

PROVIDING AN INERT ATMOSPHERE AND PROPERLY DESIGNING

RTECS: 9999999ZZ

FLAMES, THE GASES WILL BURN & MAY FORM CO

RTECS: 9999999ZZ

CANNOT BE PREDICTED BASED ON CURRENT

RTECS: 9999999ZZ

SUCH RELS ARE ALLOWED TO BUILD UP DUE TO INADEQUATE

RTECS: 9999999ZZ

PRLNG EXPOS AT HIGH CONC COULD CAUSE NAUSEA, DROW,

RTECS: 9999999ZZ

LIMITS (WHERE ESTABLISHED).GOOD INDUSTRIAL

RTECS: 9999999ZZ

CARBON BLACK

CAS: 1333-86-4

RTECS: FF5800000

OSHA PEL 3.5 MG/M3

ACGIH TLV: 3.5 MG/M3; 9192

AN INCENDIARY ELECTROSTATIC SPARK. EXCESSIVE

RTECS: 9999999ZZ

CONDITIONS. TAKE PROPER PREC WHEN TRANSFERRING TPR

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN CONT IS EXPECTED TO BE THE
PRIMARY ROUTE OF OCCUP EXPOS TO TRP W900 SERIES THERMOPLASTIC RUB.
EXPOS TO THE FINISHED PROD IN NORMAL HNDLG/STOR HAS NOT BEEN RPRTD
TO CAUSE SIGNIFICANT ADVERSE HLTH EFTS DUE TO ITS CHEM/PHYS
PROPERTIES ASA FINAL PROD, TPR W900 SERIES THERMOPLASTIC RUB DOES
NOT APPEAR(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: TO POSSESS ANY TOXICOLOGICAL
PROPERTIES WHICH WOULD REQ SPEC HNDLG OTHER THAN GOOD INDUS HYGIENE
& SAFETY PRACTICES EMPLOYED W/ANY INDUS MATL OF THIS TYPE.
HOWEVER,UNDER NORM PROCESSING CNDT N,THIS PROD RELS FUMES/VAPORS.
COMPONENTS OF THESE RELS MAY VARY W/PROCESSING TIMES/TEMPS,SPEC
COMPOSITION (ING 6 )
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INHAL: REMOVE TO FRESH AIR, IF BREATHING IS DIFFICULT, SEEK
MD ATTENTION. INGEST: SEEK MD ASSISTANCE IMMEDIATELY

Flash Point:>700F,>371C
Extinguishing Media:WATER SPRAY OR ANY CLASS A EXTINGUISHING AGENT.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL PROT
CLTHG. CO & SMOKE MAY BE LIBERATED AS TOXIC DECOMP PRODUCTS WHEN
TPR W900 SERIES THEROPLASTIC RUBBER IS IGNITED.
Unusual Fire/Explosion Hazard:COMBUST PRODS MAY INCL TOX CO AND SMOKE.
STATIC GENERATION:PNEUMATIC TRANSFER OF PLASTIC PELLETS CAN
GENERATE LARGE STATIC DISCHARGES WHICH COULD CAUSE (ING 2)

Spill Release Procedures:VACUMM OR SWEEP UP AND PLACE IN CONTAINER FOR
DISPOSAL AS RECOMMENED IN WASTE DISPOSAL METHODS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE IN A COOL, DRY PLACE.
Other Precautions:USUAL PRECAUTIONS IN PELLET HANDLING SHOULD BE
OBSERVED TO PREVENT CONTAMINATION BY DIRT OR OTHER MATERIALS. AVOID
BREATHING PROCESSING VAPORS. PROCESS WITH ADEQUATE VENTILATION.

Respiratory Protection:NIOSH/MSHA APPROVED PROT EQUIP WHEN AIRBORNE
EXPOSURE IS EXCESSIVE.CONSULT RESP MFR TO DETERMINE APPROP TYPE OF
EQUIP FOR GIVEN APPLICATN. OBSERVE RESP USE LIMITS SPECIFIED BY
NIOSH/MSHA OR THE MFR. R ESP PROT MUST COMPLY W/29 CRF 1910.124.
Ventilation:LOCAL EXHAUST VENT IS RECOMM WHERE HIGH TEMP PROCESSING
RESULTS IN GENERATION OF EXCESSIVE SMOKE AND OFF-GASSES.
Protective Gloves:IMPERVIOUS GLOVES
Eye Protection:CHEMICAL WORKERS GOGGLES
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:WASH HANDS & CONTAMINATED SKIN THOROUGHLY AFTER
USE.
Supplemental Safety and Health
MATLS TO AVOID: ACETAL RESIN AND FORMALDEHYDE AS A RXN PRODUCT. THORO
PURGE PROCESSING EQUIP W/POLYOLEFIN POLYMERS, INCL POLYPROPYLENE
WHEN USING SAME EQUIP TO PROCESS TPR THERMOPLASTIC RUBBER & ACETA L
RESINS. DO NOT MIX TPR THERMOPLASTIC RUBBER & ACETAL RESINS AT
ELEVATED TEMPERATURES.

HCC:N1
Appearance and Odor:BLACK OR NEUTRAL PELLETS, SLIGHTLY RUBBERLIKE ODOR

Stability Indicator/Materials to Avoid:YES
MAY REACT W/STRONG OXIDZING CHEM INCL FLUORINE,MAY ALSO REACT W/ ACETAL
RESINS AT HIGH TEMPS,PRDCG DECOMP OF (SUPP DATA)
Stability Condition to Avoid:TPR W900 SERIES THERMOPLASTC RUB WILL
SLOWLY DECOMP AT TEMPS >500 F, RELSG TOXIC FUMES. IF SUBJECT TO
OPEN (ING 5)
Hazardous Decomposition Products:SMOKE,CO,AND POSS HYDROCARB,MAY EVOLVE
WHEN PROCESSING TEMPS EXCEED 500 F OR WHEN TRP W900 THERMOPLASTIC
RUB IS IGNITED.

Waste Disposal Methods:NOT A HAZ WASTE AS PER 40 CFR 261. BURN IN
APPROVED INCENERATOR OR DISPOSE OF IN APPROVED CHEM LANDFILL I/A/W
ALL APPLICABLE LOCAL,STATE AND FED LAWS AND REGS. CONSULT ATTORNEY
OR APPROPRIATE REGULATO RY OFFICIALS FOR INFORMATION ON DISPOSAL.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.