Product ID:THERMOPLASTIC RUBBER, 9201-85-W900
MSDS Date:12/08/1990
FSC:9320
NIIN:00N016397
MSDS Number: BLBQK

ADVANCED ELASTOMER SYSTEMS

540 MARYVILLE CENTRE DR
ST LOUIS, MO 63166-6735
US

Emergency Phone: 314-694-1000

Info Phone: 314-694-1000

Cage: 41599

ADVANCED ELASTOMER SYSTEMS

ST LOUIS, MO 63166-6735 US

Telephone: 314-694-1000

Cage: 41599

CARBON BLACK

CAS: 1333-86-4

RTECS: FF5800000

OSHA PEL 3.5 MG/M3

ACGIH TLV: 3.5 MG/M3; 9192

AN INCENDIARY ELECTROSTATIC SPARK.EXCESSIVE

RTECS: 9999999ZZ

CONDITIONS. TAKE PROPER PREC WHEN TRANSFERRING TPR

RTECS: 9999999ZZ

PROVIDING INERT ATMOSPHERE AND PROPERLY DESIGNING

RTECS: 9999999ZZ

FLAME THE GASES WILL BURN & MAY FORM CO AND

RTECS: 9999999ZZ

CANNOT BE PREDICTED BASES ON CURRENT

RTECS: 9999999ZZ

WHERE SUCH RELS ARE ALLOWED TO BUILD UP DUE TO

RTECS: 9999999ZZ

AND PRLNG EXPOS AT HIGH CONC COULD CAUSE

RTECS: 9999999ZZ

LIMITS (WHERE ESTABLISHED).GOOD INDUSTRIAL

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN CONT IS EXPECTED TO BE PRIMARY
ROUTE OF OCCUP EXPOS TO TPR W900 SERIES THERMOPLASTIC RUB. EXPOS TO
THE FINISHED PROD IN NORMAL HNDLNG/STOR HAS NOT BEEN RPRTD TO CAUSE
SIGNIFICANT ADVERSE HLTH EFT S. DUE TO ITS CHEM/PHYS PROPERTIES AS
AFINAL PROD, TPR W900 SERIES THEMOPLASTIC RUB DOES NOT APPREAR
(EFCTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: TO POSSESS ANY TOXICOLOGICAL
PROPERTIES WHICH WOULD REQ SPEC HNDLG OTHER THAN GOOD INDUS
HYGIENE/SAFETY PRACTICES EMPLOYED W/ANY INDUS MATL OF THIS TYPE.
HOWEVER,UNDER NORM PROCESSING CNDT N,THIS PROD RELS FUMES/VAPORS.
COMPONENTS OF THESE RELS MAY VARY W/PROCESSING TIMES/TEMPS,SPEC
COMPOSITION (ING 6)
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INHAL: REMOVE TO FRESH AIR. IF BREATHING IS DIFFICULT, GET
MEDICAL ATTENTION. INGEST: GET MD IMMEDIATELY..

Flash Point:>700F,>371C
Extinguishing Media:WATER SPRAY OR ANY CLASS A EXTINGUISHING AGENT.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE CLOTHING. CARBON MONOXIDE AND SMOKE MAY BE LIBERATED AS
TOXIC DECOMP PRODUCTS WHEN RUBBER IS IGNITED.
Unusual Fire/Explosion Hazard:FIRE: COMBUSTION PRODUCTS MAY INCLUDE
TOXIC CARBON MONOXIDE AND SMOKE.

Spill Release Procedures:VACUUM OR SWEEP UP AND PLACE IN CONTAINER FOR
DISPOSAL AS RECOMMENED IN WASTE DISPOSAL METHODS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE IN A COOL, DRY PLACE.
Other Precautions:USUAL PRECAUTIONS IN PELLET HANDLING SHOULD BE
OBSERVED TO PREVENT CONTAMINATION BY DIRT OR OTHER MATERIALS. AVOID
BREATHING PROCESSING VAPORS. PROCESS WITH ADEQUATE VENTILATION.

Respiratory Protection:USE NIOSH/MSHA APPRVD RESP PROT EQUIP WHEN
AIRBORNE EXPOS IS EXCESSIVE. CONSULT RESP MFR TO DETERM APPROP TYPE
OF EQUIP FOR GIVEN APPLICATN. OBSERVE RESP USE LIMITS BY NIOSH/MSHA
OR MFR. MUST COMPLY W /29 CFR 1910.134.
Ventilation:LOCAL EXHAUST IS RECOMM WHERE HIGH TEMPS PROCESSING RESULTS
IN GENERATION OF EXCESSIVE SMOKE AND OFF-GASSES.
Protective Gloves:IMPERVIOUS GLOVES
Eye Protection:CHEMICAL WORKERS GOGGLES
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:WASH HANDS AND CONTAIMINATED SKIN THOROUGHLY
AFTER HANDLING.
Supplemental Safety and Health
MATLS TO AVOID: ACETAL RESIN & FORMALDEHYDE AS A RXN PROD. THORO PURGE
PROCESSING EQUIP W/POLYOFIN POLYMERS, INCL POLYPROPYLENE WHEN USING
SAME EQUIP TO PROCESS TPR THERMOPLASTIC RUB & ACETAL RESINS. DO
NOT MIX TPR THERMOPLASTIC RUB & ACETAL RESINS AT ELEVATED TEMPS.

HCC:N1
Appearance and Odor:BLACK OR NEUTRAL (COLORABLE) PELLETS WITH A
SLIGHTLY RUBBERLIKE ODOR

Stability Indicator/Materials to Avoid:YES
MAY REACT W/STRONG OXIDIZING CHEM INCL FLUORINE, MAY ALSO REACT
W/ACETAL RESINS AT HIGH TEMPS,PRDCG DECOMP OF(SUPP DATA)
Stability Condition to Avoid:CPR W900 SERIES THERMOPLASTIC RUB WILL
SLOWLY DECOMP AT TEMPS >500 F, RELSG TOXIC FUMES. IF SUBJECT TO
OPEN (ING 5)
Hazardous Decomposition Products:SMOKE/CO/POSS HYDROCARB, MAY EVOLVE
WHEN PROCESSING TEMPS EXCEED 500 F OR WHEN TPR W900 THERMOPLASTIC
RUB IS IGNITED

Waste Disposal Methods:NOT A HAZ AS PER 4O CFR 261. BURN IN APPROVED
INCENERATOR OR DISPOSAL OF IN APPROVED CHEM LANDFILL I/A/W ALL
APPLICABLE LOCAL,STATE,AND FED LAWS AND REGS. CONSULT ATTORNEY OR
APPROPRIATE REGULATORY OF FICIALS FOR INFO ON DISPOSAL.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.