Product ID:CHEMESTER SURFACER RESIN, 0380648
MSDS Date:10/21/1987
FSC:8040
NIIN:00N017081
MSDS Number: BLBZT

ATLAS MINERALS & CHEMICALS INC

MERTZTOWN, PA 19539-0038
US

Emergency Phone: 215-682-9123

Info Phone: 215-682-7171

Cage: 04503

ATLAS MINERALS & CHEMICAL INC

MERTZTOWN, PA 19539-0038 US

Telephone: 215-682-7171

Cage: 04503

VINYL ESTER RESIN

Fraction By Weight: 45-55%

STYRENE, MONOMER (SARA III)

CAS: 100-42-5

RTECS: WL3675000

Fraction By Weight: 40-50%

OSHA PEL 100 PPM

ACGIH TLV: S,50PPM/100STEL;9293

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

WAX DISPERSION

Fraction By Weight: 1%

PIGMENTS DISPERSED IN POLYESTER

Fraction By Weight: 0-6%

IRON OXIDE

CAS: 1309-37-1

RTECS: NO7400000

Fraction By Weight: 0-5%

OSHA PEL 10 MG/M3 (FE)

ACGIH TLV: 5 MG/M3(FE),B2; 9293

DIBUTYL PHTHALATE (SARA III)

CAS: 84-74-2

RTECS: TI0875000

Fraction By Weight: 0-5%

OSHA PEL 5 MG/M3

ACGIH TLV: 5 MG/M3; 9192

EPA Report Quantity: 10 LBS

DOT Report Quantity: 10 LBS

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:YES OSHA:NO
Health Hazards Acute and Chronic:EYES: CONTACT CAUSES IRRITATION. SKIN:
REPEATED CONTACT CAUSES IRRITATION, DEFATTING, DERMATITIS. INHAL:
RSLTS IN IRRIT TO RESP TRACT. CHRONIC EFTS OF OVEREXP: LIVER
ABNORMALITIES,KIDNEY & LUNG DAMAGE IN LAB ANIMALS. OVEREXP TO
STYRENE HASAPPARENTLY BEEN FOUND TO CAUSE THE FOLLOWING EFTS IN LAB
(SEE EFTS OF OVEREXP)
Explanation of Carcinogenicity:STYRENE: IARC GROUP 2B.
Effects of Overexposure:HLTH HAZ: ANIMALS: LIVER ABNORMAL, KIDNEY/LUNG
DAM.
Medical Cond Aggravated by Exposure:RESPIRATORY PROBLEMS, ALLERGIES.

First Aid:EYES: FLUSH WITH CLEAR WATER FOR AT LEAST 15 MIN. GET MED
ATTN. SKIN: WASH CONTACT AREA WITH SOAP AND WATER. IF SKIN IS RED,
ITCHING OR BURNED, GET MED ATTN. INHAL: REMOVE VICTIM TO FRESH AIR.
IF BREA THING STOPS BEGIN ARTFICIAL RESPIRATION. GET MED ATTN.
INGEST: DO NOT INDUCE VOMIT. GET MED ATTN.

Flash Point Method:SCC
Flash Point:92.0F,33.3C
Extinguishing Media:CO*2, FOAM, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND PROTECTIVE
CLOTHING. WATER MAY BE INEFFECTIVE, BUT CAN BE USED TO COOL FIRE
EXPOSED CONTAINERS.
Unusual Fire/Explosion Hazard:VAP ARE HEAVIER THAN AIR/MAY TRAVEL
CONSIDERABLE DIST TO AN IGNIT SOURCE/FLASH BACK. FIGHT FIRE FROM
SAFE DIST. STYRENE FIRES PRDC COPIOUS AMTS OF DENSE SMOKE.

Spill Release Procedures:ELIM ALL SOURCES OF IGNIT, VENT AREA. ABSORB
SPILLED MATL W/ABSORB & PLACE IN APPROPRIATE CONTR FOR DISPOSAL.
RESIDUAL RESINS CAN BE REMOVED WITH METHYLENE CHLORIDE, ACETONE OR
AROMATIC SOLVENTS. WEAR EYE PROT, PROT CLTHG & RESP PROT DURING
CLEAN UP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:STORE AWAY FROM HEAT, SPARKS OR
FLAMES. PREFERRED STORAGE TEMP IS 50 TO 60 F, AVOID BREATHING VAP.
AVOID SKIN/EYE CONTACT. DO NOT TAKE INTERNALLY.
Other Precautions:FOR INDUSTRIAL USE ONLY. KEEP OUT OF REACH OF
CHILDREN.

Respiratory Protection:WEAR NIOSH/MSHA APPROVED ORGANIC VAPOR MASK IF
TLV IS EXCEEDED OR USED IN CONFINED AREAS.
Ventilation:LOCAL: PROVIDE VENTILATION ADEQUATE TO KEEP EXPOSURE BELOW
TLV. MECHANICAL: ACCEPTABLE.
Protective Gloves:PLASTIC OR RUBBER.
Eye Protection:CHEMICAL WORKERS GOGGLES. (SUPP DATA)
Other Protective Equipment:SAFETY SHOWER, EYE BATH, CLEAN BODY COVER
CLOTHES.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EYE PROT: MAY ADD FULL LENGTH FACESHIELD TO GOGGLES .

HCC:F4
Boiling Pt:B.P. Text:293F,145C
Vapor Pres:4.3 @68F
Vapor Density:>AIR
Spec Gravity:1.05
Evaporation Rate & Reference:SLOWER THAN BUTYL ACETATE
Solubility in Water:NEGLIGIBLE
Appearance and Odor:COLORED LIQUID WITH CHARACTERISTIC ODOR.
Percent Volatiles by Volume:40

Stability Indicator/Materials to Avoid:YES
OXIDIZING MATERIALS, STRONG ACIDS, COPPER AND COPPER ALLOYS.
Stability Condition to Avoid:DIRECT SUNLIGHT, TEMPERATURES ABOVE 120F.
MAY RESULT IN GRADUAL THICKENING AND GELATION.
Hazardous Decomposition Products:ACRID FUMES, PHENOL DERIVATIVES, AND
CARBON MONOXIDE.
Conditions to Avoid Polymerization:CONTACT WITH OXIDIZING MATERIALS,
HIGH TEMPERATURES.

Waste Disposal Methods:DISPOSE IN ACCORDANCE WITH APPLICABLE LOCAL,
STATE AND FEDERAL ENVIRONMENTAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.