Product ID:PARAPOL 1300, 81331000
MSDS Date:11/05/1992
FSC:9150
NIIN:00N058903
MSDS Number: BXFNS

EXXON CHEMICAL AMERICAS

HOUSTON, TX 77253
US

Emergency Phone: 800-424-9300 (CHEMTREC)

Info Phone: 908-474-2828

Cage: 72190

EXXONMOBIL CHEMICAL CO, DIV OF EXXON MOBILCORP.

3272 HOUSTON, TX 77253-3272 US

Telephone: 281-870-6000 / 800-726-2015

Cage: 72190

BUTENE, POLYMERS; (POLYBUTENE)

CAS: 9003-29-6

RTECS: EM9032000

OSHA PEL N/K

ACGIH TLV: N/K

PHARMACEUTICAL GRADE MINERAL OIL/FOOD GRADE

RTECS: 9999999ZZ

REMOVE AFFECTED VICTIM FROM EXPOS. ADMINISTER ARTF

RTECS: 9999999ZZ

CALL MD IMMED .

RTECS: 9999999ZZ

THIS PROD IS SUBJECT TO CERCLA REPORTING,

RTECS: 9999999ZZ

SEWERS, WATERCOURSES/LOW AREAS. CONTAIN SPILLED LIQ

RTECS: 9999999ZZ

IF LIQ TOO VISCOUS FOR PUMPING, SCRAPE UP. WATER

RTECS: 9999999ZZ

IF ALLOWED BY LOC AUTH & ENVIRONMENTAL AGENCIES,

RTECS: 9999999ZZ

TEMPS CAN ALSO BE CATALYSED BY IRON/RUST. ALL

RTECS: 9999999ZZ

RUST TO MIN POTENTIAL FOR PRODUCING FLAM DECOMP

RTECS: 9999999ZZ

PROMOTE RAPID FOAMING IN THE TANK WITH THE

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: EYES: SLIGHTLY IRRIT BUT DOES
NOT INJURE EYE TISS. SKIN: EXPOS TO HOT MATL MAY CAUSE THERMAL
BURNS & ADHESION OF SOLIDIFIED PROD TO SKIN. INHAL: NEGLIGIBLE HAZ
AT AMBIENT (-18 TO 38C; 0 TO 100F )/RECOM BLENDING TEMP. AVOID
BRTHG VAPS/MISTS. INGEST: MINIMAL TOXICITY.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:EYES: FLUSH W/LGE AMTS OF WATER FOR AT LEAST 15 MIN. UNTIL
IRRIT SUBSIDES. IF IRRIT PERSISTS, GET MD ATTN. SKIN: REMOVE
GROSSLY CONTAM CLTHG, INCL SHOES, & LAUNDER BEFORE REUSE. FOR HOT
PROD, IMMED IM MERSE IN/FLUSH AFFECTED AREA OF SKIN W/LGE AMTS OF
COLD WATER TO DISSIPATE HEAT & REDUCE EXTENT OF THERMAL BURNS.
SOLIDIFIED PROD MAY BE REMOVED FROM SKIN BY GENTLY RUBBING W/GAUZE
& EITHER A (ING 2)

Flash Point Method:PMCC
Flash Point:360F,182C
Extinguishing Media:ISOLATE "FUEL" SUPPLY FROM FIRE. USE FOAM, DRY
CHEMICAL OR WATER SPRAY.
Fire Fighting Procedures:USE WATER SPRAY TO COOL FIRE EXPOSED SURFACES
AND TO PROTECT PERSONNEL. WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT.
Unusual Fire/Explosion Hazard:TOX GASES WILL FORM UPON COMBUST. "EMPTY"
CONTRS RETAIN PROD RESIDUE (LIQ &/VAP) & CAN BE DANGEROUS. DO NOT
PRESSURIZE, CUT, WELD, BRAZE, SOLDER, (SUP DAT)

Spill Release Procedures:LAND SPILL: ELIMINATE SOURCES OF IGNIT.
PREVENT ADDIN DISCHARGE OF MATL, IF POSS TO DO SO W/OUT HAZ. FOR
SML SPILLS IMPLEMENT CLEAN UP PROC. FOR LGE SPILLS IMPLEMENT CLEAN
UP PROC &, IF IN PUBLIC AREA , KEEP PUBLIC AWAY & ADVISE AUTH.
ALSO,IF (ING 5)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:USE PROPER GROUNDING PROC. STORE AT
180F MAX, & AT ATMOSPHERIC PRESS. LOADING TEMP: 200F. LOADING
VISCOSITY: 800.
Other Precautions:TANKS SHOULD HAVE ADEQ AGITATION TO AVOID EXCESSIVE
TANK SKIN TEMPS. HEATING MEDIUM TEMP SHOULD NOT EXCEED 370F (TEMP
OF 150LB STEAM). OVERHEATING MAY CAUSE PROD DECOMP TO BUTENES &
SUBSEQUENTLY CREAT E A FLAM HAZ. DECOMP AT HIGH (ING 9)

Respiratory Protection:WHERE CONCENTRATIONS IN AIR MAY EXCEED THE
LIMITS GIVEN IN THIS SECTION AND ENGINEERING, WORK PRACTICE OR
OTHER MEANS OF EXPOSURE REDUCTION ARE NOT ADEQUATE, NIOSH/MSHA
APPROVED RESPIRATORS MAY BE NEC ESSARY TO PREVENT OVEREXP BY INHAL.
Ventilation:LOC EXHAUST RECOM TO CTL PROCESS EMISSIONS NEAR SOURCE. LAB
SAMPLES SHOULD BE STORED & HANDLED IN LAB HOOD. (SUP DAT)
Protective Gloves:THERMAL RESISTANT GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:WHERE CONTACT MAY OCCUR WITH HOT MATERIAL
WEAR ARM PROTECTION.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXPLO HAZ: DRILL, GRIND/EXPOSE SUCH CONTRS TO HEAT, FLAME, SPARKS,
STATIC ELEC/OTHER SOURCES OF IGNIT; THEY MAY EXPLODE & CAUSE
INJURY/DEATH. EMPTY DRUMS SHOULD BE COMPLETELY DRAINED, PROPERLY
BUNGED & PROMPTLY RETURNED TO DRUM RECONDITIONER/PROPERLY DISPOSED
OF. VENT: PROVIDE MECH VENT OF CONFINED SPACES.

Melt/Freeze Pt:M.P/F.P Text:Vapor Pres:NEGLIGIBLE
Vapor Density:7.5 @ 60F
Spec Gravity:0.90 @ 60F
Evaporation Rate & Reference:NEGLIGIBLE (N-BU ACET=1)
Solubility in Water:NEGLIGIBLE
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NONE.
Hazardous Decomposition Products:FUMES, SMOKE, AND CARBON MONOXIDE.

Waste Disposal Methods:CONSULT AN EXPERT ON DISPOSAL OF RECOVERED
MATERIAL AND ENSURE CONFORMITY TO LOCAL, STATE AND FEDERAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.