BBFMP - TYPE 1 SUPERFINE

  • MSDS: BBFMP
  • Manufacturer: ESSCHEM CO
  • Product Name: TYPE 1 SUPERFINE
  • National Stock Number: 6520-00D001858
Product Identification

Product ID:TYPE 1 SUPERFINE
MSDS Date:12/20/1984
FSC:6520
NIIN:00D001858
MSDS Number: BBFMP

Responsible Party
ESSCHEM CO.
ESSINGTON, PA 19029

Emergency Phone: 215-521-3800

Info Phone: 215-521-3800

Preparer: GFC

Cage: EO118

Contractor
ESSCHEM CO.
ESSINGTON, PA 19029 US

Telephone: 215-521-3800

Cage: EO118

Ingredients

PLASTICIZED POLY METHYLMETHACRYLATE

OSHA PEL 100PPM (FOR MONOMER)

ACGIH TLV: 100PPM (FOR MONOMER)


DIALKYL PHTHALATE

Fraction By Weight: <15%

Hazards

Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:IT IS NOT KNOWN TO CAUSE SIGNIFICANT
HEALTH PROBLEMS. IT IS CONSIDERED AN INERT OR NUISANCE DUST. AVOID
INHALATION OF DUST. KEEP DUST OUT OF EYES TO PREVENT POSSIBLE
IRRITATION.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE NOTED

First Aid

First Aid:EYES:FLUSH WITH WATER FOR 5 MINUTES;SKIN:WASH WITH SOAP &
WATER;INHALATION:REMOVE TO FRESH AIR.SEE DOCTOR IF IRRITATION
PERSISTS;INGESTION:RINSE MOUTH OUT WITH WATER.CALL DOCTOR IF AMOUNT
WAS LARGE.

Fire Fighting

Flash Point Method:TCC
Flash Point:579F,304C
Extinguishing Media:WATER,CO*2,DRY CHEMICAL
Fire Fighting Procedures:AVOID EXTINGUISHING METHODS WHICH MAY GENERATE
DUST CLOUDS. WATER STREAM CAN DISPERSE DUST IN AIR,PRODUCING A FIRE
HAZARD & POSSIBLE EXPLOSION HAZARD.
Unusual Fire/Explosion Hazard:POLYMER DUST IS COMBUSTIBLE.EXPLOSIVE
LIMITS OF POLYMER PARTICLES ARE AS THOSE OF COAL DUST. FIREFIGHTERS
WEAR SCBA.

Accidental Release

Spill Release Procedures:SWEEP UP TO AVOID SLIPPING HAZARD.KEEP
AIRBORNE PARTICULATE AT A MINIMUM WHEN CLEANING UP SPILLS.

Handling

Handling and Storage Precautions:STORE IN COOL DRY PLACE. KEEP
CONTAINERS CLOSED TO PREVENT WATER ABSORPTION AND CONTAMINATION.

Exposure Controls

Respiratory Protection:NIOSH/MSHA APPROVED DUST RESPIRATOR FOR NUISANCE
DUST.
Ventilation:LOCAL EXHAUST AT PROCESSING EQUIPMENT
Protective Gloves:WEAR PROTECTIVE GLOVES FOR HOT PLASTIC
Eye Protection:SAFETY GLASSES
Other Protective Equipment:HIGH TEMPERATURE PROCESSING EQUIPMENT SHOULD
BE VENTILATED.
Work Hygienic Practices:WASH AFTER HANDLING
Supplemental Safety and Health

Chemical Properties

Evaporation Rate & Reference:NIL
Solubility in Water:INSOLUBLE
Appearance and Odor:FINE WHITE POWDER. FAINT ODOR IN BULK
Percent Volatiles by Volume:<5

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:HEATING ABOVE 572F,300C.
Hazardous Decomposition Products:METHYLMETHACRYLATE MONOMER AND CO.

Disposal

Waste Disposal Methods:MAY BE DISPOSED OF IN LANDFILL OR INCINERATED.
FOLLOW FEDERAL,STATE AND LOCAL DISPOSAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.