BBYRB - DENS-COTE PLASTERS (ALL TYPES)
- MSDS: BBYRB
- Manufacturer: GEORGIA PACIFIC CORP
- Product Name: DENS-COTE PLASTERS (ALL TYPES)
- National Stock Number: 5640-00F007726
Product Identification
Product ID:DENS-COTE PLASTERS (ALL TYPES)
MSDS Date:11/01/1985
FSC:5640
NIIN:00F007726
MSDS Number: BBYRB
Responsible Party
DECATUR, GA 30035
Emergency Phone: (404) 987-5190
Info Phone: (800) 424-9300
Preparer: NANCY E. WAGNER
Cage: 00284
Contractor
Telephone: (404) 987-5190
Cage: 00284
Ingredients
PLASTER OF PARIS (CALCIUM SULFATE DIHYDRATE)
CAS: 10101-41-4
RTECS: EW4150000
Fraction By Weight: 49-94%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3 TDUST; 9293
SILICA, CRYSTALLINE - QUARTZ
CAS: 14808-60-7
RTECS: VV7330000
Fraction By Weight: 0-49%
OSHA PEL SEE TABLE Z3
ACGIH TLV: 0.1 MG/M3 RDUST;9293
TALC (POWDER), (ASBESTOS FREE)
CAS: 14807-96-6
RTECS: VV7720000
Fraction By Weight: 0-26%
OSHA PEL 15 MG/CUM
ACGIH TLV: 2 MG/CUM (RESP DUST)
MICA - SILICATES (< 1% CRYSTALLINE SILICA)
CAS: 12001-26-2
RTECS: VV8760000
Fraction By Weight: 0-21%
OSHA PEL 20 MPPCF
ACGIH TLV: 3 MG/M3 RDUST; 9293
SILICA-AMORPHOUS DIATOMACEOUS EARTH (UNCALCINED)
CAS: 68855-54-9
RTECS: VV7309000
Fraction By Weight: 0-13.6%
OSHA PEL 80 MG/CUM
ACGIH TLV: 10 MG/CUM (DUST)
CALCIUM OXIDE
CAS: 1305-78-8
RTECS: EW3100000
Fraction By Weight: 0-6.2%
OSHA PEL 5 MG/M3
ACGIH TLV: 2 MG/M3; 9192
STARCH
CAS: 9005-25-8
RTECS: GM5090000
Fraction By Weight: 0-4.4%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3; 9192
PARTICULATES NOT OTHERWISE REGULATED (NUISANCE DUST)
Fraction By Weight: BALANCE
OSHA PEL 15 MG/M3 TOTAL DUST
ACGIH TLV: 10 MG/M3 TDUST; 8990
Hazards
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION: MAY CAUSE DELAYED LUNG
INJURIES, SILICOSIS, PNEUMOCONIOSIS, PULMONARY FIBROSIS, SHORTNESS
OF BREATH & HEART FAILURE, COUGHING, SNEEZING & NASAL IRRITATION.
SKIN: MAY CAUSE BURNS IF LARGE M ASS IS IN CONTACT W/SKIN DURING
HARDENING (HYDRATION); MAY DRY SKIN. EYES: MAY CAUSE IRRITATION.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:INHALATION: MAY CUASE DELAYED LUNG INJURIES,
SILICOSIS, PNEUMOCONIOSIS, PULMONARY FIBROSIS, SHORTNESS OF BREATH
& HEART FAILURE, COUGHING, SNEEZING & NASAL IRRITATION. SKIN: MAY
CAUSE BURNS & DRY. EYE S: MAY CAUSE IRRITATION.
First Aid
First Aid:INGESTION: PRODUCT MAY HARDEN ON CONTACT WITH WATER. MAY
RESULT IN OBSTRUCTION IF INGESTED. SEE PHYSICIAN. INHALATION:
REMOVE TO FRESH AIR. EYE: REMOVE CONTACT LENSES. RINSE EYES WITH
PLENTY OF RUNNIN G WATER FOR 10-15 MINUTES, INCLUDING UNDER
EYELIDS. IF IRRITATION OCCURS, CONTACT PHYSICIAN. SKIN: WASH
PROMPTLY WITH WATER. IF IRRITATION OCCURS, CONTACT PHYSICIAN.
Fire Fighting
Flash Point:NONE
Extinguishing Media:NON-COMBUSTIBLE
Fire Fighting Procedures:NONE
Unusual Fire/Explosion Hazard:NONE
Accidental Release
Spill Release Procedures:SWEEP OR VACCUM SPILLED MATERIAL INTO A WASTE
CONTAINER FOR DISPOSAL. AVOID CREATING EXCESSIVE DUST. WEAR
APPROVED RESPIRATORS IF NECESSARY. DON'T WASH DOWN DRAINS - MAY
PLUG DRAINS.
Handling
Handling and Storage Precautions:BE SURE PROPER VENTILATION &
RESPIRATORY & EYE PROTECTION ARE USED UNDER DUSTING CONDITIONS.
Other Precautions:EXCESSIVE PARTICULATE IN WORKPLACE AIR MUST BE
AVOIDED. WHERE APPLICABLE, USE WET SPONGING IN LIEU OF DRY SANDING
WHENEVER POSSIBLE. DEW POINT CONDITIONS/OTHER CONDITIONS CAUSING
PRESENCE OF MOISTURE WILL HARDEN GYPSUM CEMENT DURING STORAGE
Exposure Controls
Respiratory Protection:WEAR NIOSH-APPROVED RESPIRATOR AS APPROPRIATE
FOR NUISANCE & LUNG DAMAGING DUSTS, ESPECIALLY WHEN SANDING, DRY
GRINDING, CRUSHING & MILLING.
Ventilation:PROVIDE LOCAL EXHAUST VENTILATION TO KEEP
Eye Protection:GOGGLES
Work Hygienic Practices:WHEN WET SPONGING IN LIEU OF DRY SANDING WHEN
POSSIBLE.
Supplemental Safety and Health
Chemical Properties
Spec Gravity:2.5
pH:8.5-10
Solubility in Water:<0.2%
Appearance and Odor:WHITISH, GREY OR BUFF POWDER; LOW ODOR
Stability
Stability Indicator/Materials to Avoid:YES
(CRYSTALLINE SILICA): ENDOTHERMIC - DISSOLVED BY HYDROFLUORIC ACID.
Stability Condition to Avoid:HYDROFLUORIC ACID
Hazardous Decomposition Products:NONE
Disposal
Waste Disposal Methods:MAY BE DISPOSED OF AS INERT SOLID IN SANITARY
LANDFILL OR BY OTHER PROCEDURES IN ACCORDANCE WITH ALL FEDERAL,
STATE & LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.