BBYSP - MOLDING PLASTER
- MSDS: BBYSP
- Manufacturer: GEORGIA PACIFIC CORP
- Product Name: MOLDING PLASTER
- National Stock Number: 5640-00F007758
Product Identification
Product ID:MOLDING PLASTER
MSDS Date:11/01/1985
FSC:5640
NIIN:00F007758
MSDS Number: BBYSP
Responsible Party
DECATUR, GA 30035
Emergency Phone: (404) 987-5190
Info Phone: (404) 987-5190
Preparer: NANCY E. WAGNER
Cage: 00284
Contractor
Telephone: (404) 987-5190
Cage: 00284
Ingredients
PLASTER OF PARIS (CALCIUM SULFATE DIHYDRATE)
CAS: 10101-41-4
RTECS: EW4150000
Fraction By Weight: 49-99.5%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3 TDUST; 9293
PORTLAND CEMENT
CAS: 65997-15-1
RTECS: VV8770000
Fraction By Weight: 0-49%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3 TDUST; 9293
STARCH
CAS: 9005-25-8
RTECS: GM5090000
Fraction By Weight: 0-4%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3; 9192
PARTICULATES NOT OTHERWISE REGULATED (NUISANCE DUST)
Fraction By Weight: BALANCE
OSHA PEL 15 MG/M3 TOTAL DUST
ACGIH TLV: 10 MG/M3 TDUST; 8990
PERLITE
CAS: 93763-70-3
RTECS: SD5254000
Fraction By Weight: 0-14%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3 TDUST; 9192
Hazards
Routes of Entry: Inhalation:NO Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:COUGHING, SNEEZING & NASAL IRRITATION.
SKIN: MAY DEVELOP ENOUGH HEAT TO CAUSE BURNS IF LARGE MASS IS IN
CONTACT WITH SKIN DURING HARDENING (HYDRATION); MAY DRY SKIN. EYES:
MAY CAUSE IRRITATION.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:COUGHIN,G SNEEZING & NASAL IRRITATION. SKIN:
MAY DEVELOP ENOUGH HEAT TO CAUSE BURNS IF LARGE MASS IS IN CONTACT
WITH SKIN DURING HARDENING (HYDRATION); MAY DRY SKIN. EYES: MAY
CAUSE IRRITATION.
First Aid
First Aid:INGESTION: PRODUCT MAY HARDEN ON CONTACT WITH WATER. MAY
RESULT IN OBSTRUCTION. SEE PHYSICIAN. INHALATION: REMOVE TO FRESH
AIR. EYE: REMOVE CONTACT LENSES. RINSE EYES WITH PLENTY OF RUNNING
WATER FOR 10-15 MINUTES, INCLUDING UNDER EYELIDS.IF IRRITATION
OCCURS, CONTACT PHYSICIAN. SKIN: WASH PROMPTLY WITH WATER. IF
IRRITATION OCCURS, CONTACT PHYSICIAN.
Fire Fighting
Extinguishing Media:NON-COMBUSTIBLE
Fire Fighting Procedures:NONE
Unusual Fire/Explosion Hazard:NONE
Accidental Release
Spill Release Procedures:SWEEP OR VACUUM SPILLED MATERIAL INTO A WASTE
CONTAINER FOR DISPOSAL. AVOID CREATING EXCESSIVE DUST. WEAR
APPROVED RESPIRATORS IF NECESSARY. DON'T WASH DOWN DRAINS - MAY
PLUG DRAINS.
Handling
Handling and Storage Precautions:BE SURE PROPER VENTILATION &
RESPIRATORY & EYE PROTECTION ARE USED UNDER DUSTING CONDITIONS.
Other Precautions:EXCESSIVE PARTICULATE IN WORKPLACE AIR MUST BE
AVOIDED EVEN THOUGH IT'S INERT & NON-TOXIC.
Exposure Controls
Respiratory Protection:WEAR NIOSH-APPROVED RESPIRATOR AS APPROPRIATE
FOR NUISANCE DUST, ESPECIALLY WHEN SANDING, DRY GRINDING, CRUSHING
& MILLING.
Ventilation:PROVIDE LOCAL EXHAUST VENTILATION TO KEEP
Eye Protection:GOGGLES
Work Hygienic Practices:WHERE APPLICABLE, USE WET SPONGING IN LIEU OF
DRY SANDING WHENEVER POSSIBLE.
Supplemental Safety and Health
Chemical Properties
Spec Gravity:.04-2.7
pH:8.5-10
Solubility in Water:.2%
Appearance and Odor:WHITISH, GREY OR BUFF POWDER; LOW ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
NONE
Stability Condition to Avoid:NONE
Hazardous Decomposition Products:CALCIUM OXIDE & SULFUR DIOXIDE
Disposal
Waste Disposal Methods:MAY BE DISPOSED OF AS INERT SOLID IN SANITARY
LANDFILL OR BY OTHER PROCEDURES IN ACCORDANCE WITH ALL FEDERAL,
STATE & LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.