Product ID:HD-3475(FORMERLY H2-3475)
MSDS Date:01/01/1985
FSC:8040
NIIN:00-079-7942
MSDS Number: BCXSH

Emergency Phone: (716) 372-6300

Cage: KO004

Telephone: 716-372-6300/6309

Cage: KO004

DIETHYLENE TRIAMINE

CAS: 111-40-0

RTECS: IE1225000

Fraction By Weight: >10%.

OSHA PEL 1 PPM

ACGIH TLV: S, 1 PPM; 9192

Effects of Overexposure:CAUSES SEVERE EYE & SKIN BURNS

First Aid:SKIN:WASH IMMEDIATELY W/SOAP & WATER.EYES:IMMEDIATELY FLUSH
W/WATER AT LEAST 15 MIN. CALL MD.

Flash Point:215F OC
Extinguishing Media:WATER SPRAY,DRY CHEMICAL "ALCOHOL"FOAM,CO*2
Fire Fighting Procedures:COOL EXPOSED CONTAINERS W/WATER.SEE OTHER
PRECAUTIONS
Unusual Fire/Explosion Hazard:CARE MUST BE USED TO PREVENT IGNITION
WHEN PROCESSING OR HANDLING AT TEMPS ABOVE THE FLASH POINT.

Spill Release Procedures:SMALL AMOUNTS CAN BE FLUSHED AWAY WITH
WATER.LARGER SPILLS SHOULD BE SCRAPED UP,TRANSFER TO A METAL
CONTAINER.

Handling and Storage Precautions:PROTECT FROM PHYSICAL DAMAGE.STORE IN
A COOL,DRY,WELL VENTILATED AREA AWAY FROM ACUTE FIRE HAZARD.STRONG
SKIN SENSITIZER.AVOID SKIN CONTACT
Other Precautions:WATER SPRAY MAY BE USED DURING FIRE TO FLUSH SPILLS
AWAY FROM EXPOSURES AND TO DILUTE SPILLS TO NON FLAMMABLE MIXTURES

Respiratory Protection:NIOSH/MSHA APPROVED RESPIRATORY PROTECTION IF
NECESSARY
Ventilation:DO NOT RECIRCULATE UNLESS SCRUBBED W/ACID
Protective Gloves:PLASTIC/RUBBER
Eye Protection:GOGGLES IF SPLASH LIKELY
Other Protective Equipment:USE OF PROTECTIVE SKIN CREAM IS RECOMMENDED
Supplemental Safety and Health
VAPOR PRESSURE:<1 MMHG.PERCENT VOLATILE BY VOLUME:NIL.PART B OF A TWO
PART PRODUCT.PART A IS R8-2038,SEE SAME NSN,P/N INDICATOR A MIX
RATION (BY WEIGHT)PART A/PART B IS 100/25.

HCC:N1
Boiling Pt:B.P. Text:404 F
Vapor Density:3.5
Spec Gravity:1.0
Solubility in Water:COMPLETE
Appearance and Odor:AMBER,MED.VISCOSTY LIQ;STRONG NH*3 LIKE ODOR.

Stability Indicator/Materials to Avoid:YES
AVOID CONTAMINATION W/STRONG ACIDS
Hazardous Decomposition Products:THERMAL DECOMP-HYDROGEN
CYANIDE,NITROGEN OXIDES,CO & CO*2
Conditions to Avoid Polymerization:MIXING LGE BATCHS OF RESIN
W/PRODUCT-DEVELPMNT EXOTHERM HEAT

Waste Disposal Methods:DISPOSE IN ACCORDANCE W/LOCAL STATE AND FEDERAL
REGULATIONS.MFR RECOMMENDS SOLIDIFY BEFORE LANDFILL BURIAL.MFR ALSO
RECOMMENDS THIS IS NOT A HAZARDOUS WASTE UNDER THE RESOURCE
CONSERVATION AND RECOVER Y ACT

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.