BHCBN - ENAMEL ALKYD GLOSS 43 WHITE 17875 ID74232

  • MSDS: BHCBN
  • Manufacturer: PRATT AND LAMBERT INC
  • Product Name: ENAMEL ALKYD GLOSS 43 WHITE 17875 ID74232
  • National Stock Number: 8010-00-286-9088
Product Identification

Product ID:ENAMEL ALKYD GLOSS 43 WHITE 17875 ID74232
MSDS Date:03/22/1988
FSC:8010
NIIN:00-286-9088
MSDS Number: BHCBN

Responsible Party
PRATT AND LAMBERT INC
16116 E 13TH ST
WICHITA, KS 67201
US

Emergency Phone: 716-873-6000

Info Phone: 316-733-1361

Preparer: W.A. ELLISON

Cage: 61196

Contractor
PRATT AND LAMBERT INC
6027 CLEVELAND, OH 44101-1027 US

Telephone: 216-566-2902

Cage: 61196

Ingredients

VM&P NAPHTHA (LIGROINE)

CAS: 8032-32-4

RTECS: OI6180000

OSHA PEL 300 PPM/400 STEL

ACGIH TLV: 300 PPM; 9192


TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293


MINERAL SPIRITS (VP MM HG @ 20 DEG C)

CAS: 64475-85-0

RTECS: PY8240000

OSHA PEL 500 PPM 2950 MG/CUM

ACGIH TLV: 100 PPM 525 MG/CUM


VOL ORGANIC CMPD 3.8 LB/GL LESS WATER & NPRS* 456 G/L LESS

RTECS: 9999999VO

Hazards

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SWALLOWING-DO NOT INDUCE VOMITING. GET
MED ATTN. INHALATION-MOVE TO FRESH AIR, KEEP WARM & QUIET, GET MED
ATTN. EYE-FLUSH WITH LARGE AMOUNTS OF WATER. GET MED ATTN.
SKIN-REMOVE CONTAMINATED CLOTHING. WASH AFFECTED AREA. NOTE TO
PHYSICIAN:OVEREXPOSURE SHOULD BE DIRECTED AT THE CONTROL OF
SYMPTOMS AND THE CLINICAL COND.
Explanation of Carcinogenicity:AT THE TLV THE TI02 MANUFACTURER
CONCLUDES THAT THERE IS NO SIGNIFICANT HAZARD FOR MAN.
Effects of Overexposure:PROLONGED & REPEATED OCCUPATION OVEREXPOSURE TO
SOLVENTS WITH PERMANENT BRAIN AND NERVOUS SYSTEM DAMAGE. DELIBERATE
CONCENTRATION & INHALING MAY BE FATAL. HIGH CONCENTRATIONS MAY
CAUSE ACUTE CENTRAL N ERVOUS SYSTEM DEPRESSION CHARACTERIZED BY
HEADACHES,DIZZINESS,NAUSEA AND CONFUSION.
Medical Cond Aggravated by Exposure:NONE LISTED.

First Aid

First Aid:SEE ABOVE.

Fire Fighting

Flash Point:102F/48.89V
Extinguishing Media:CLASS B FIRE EXTINGUISHING FOR FLAMMABLE LIQUID
FIRES.POLYMER FOAM IS PREFERRED FOR LARGE FIRES.
Fire Fighting Procedures:WEAR SELF-CONTAINED BREATHING APPARATUS. WATER
MAY BE USED TO COOL EXPOSED CONTAINERS TO PREVENT PRESSURE
BUILD-UP/AUTO IGNITION/EXPLOSION WHEN EXPOSED TO HEAT
Unusual Fire/Explosion Hazard:ISOLATE FROM HEAT/ELECTRICAL
EQUIPMENT/SPARKS/FLAME.KEEP CONTAINERS CLOSED. OVEREXPOSURE TO
DECOMPOSITION PRODUCTS MAY CAUSE A HEALTH HAZARD.OBTAIN MED ATTN.

Accidental Release

Spill Release Procedures:ELIMINATE ALL IGNITION SOURCES. DIKE WITH
INERT MATERIAL. PUT IN METAL CONTAINERS FOR RECOVERY OR DISPOSAL.
USE ONLY NON-SPARKING TOOLS. PREVENT CONTAMINATION OF
SEWERS/STREAMS/GROUNDWATER WITH SPILLE D MATERIAL OR USED
ABSORBENT.

Handling

Handling and Storage Precautions:DO NOT STORE ABOVE 95F. STORE LARGE
QUANTITIES IN COMPLIANCE WITH OSHA 29CFR1910.106. RCRA
CLASSIFICATION WOULD BE D001. NO KNOWN ENVIRONMENTAL HAZ.
Other Precautions:DO NOT TAKE INTERNALLY. DO NOT WELD/BRAZE/CUT ON
EMPTY CONTAINER.DO NOT RE-USE ANY CONTAINERS.NEVER USE PRESSURE TO
EMPTY.DRUM IS NOT A PRESSURE VESSEL. CONTAINERS SHOULD BE GROUNDED
AND BONDED TO THE RECEIVING CONTAINER.

Exposure Controls

Respiratory Protection:IN RESTRICTED VENTILATION AREAS A NIOSH APPROVED
CHEMICAL CARTRIDGE RESPIRATOR MAY BE REQUIRED. IN CONFINED AREAS
USE A NIOSH/MSHA AIR SUPPLIED RESPIRATOR. REFER TO OSHA
29CFR1910.134.
Ventilation:GENERAL DILUTION & LOCAL EXHAUST VENTILATION. REMOVE
DECOMPOSITION PROD THAT ARE GENERATED WHEN WELDING/CUTTING/BRAZING.
Protective Gloves:SOLVENT IMPERMEABLE GLOVES.
Eye Protection:WEAR SAFETY SPECTACLES.
Other Protective Equipment:NOT LIKELY TO BE NEEDED.
Supplemental Safety and Health
NONE LISTED.

Chemical Properties

HCC:F4
Boiling Pt:B.P. Text:280F/388F
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:57

Stability

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS OR ALKALINE MATERIALS.
Stability Condition to Avoid:AVOID EXCESSIVE HEAT AND SOURCES OF
IGNITION.
Hazardous Decomposition Products:BURNING/WELDING/CUTTING WILL PRODUCE
SMOKE,CARBON MONOXIDE AND CARBON DIOXIDE.
Conditions to Avoid Polymerization:KEEP AWAY FROM HEAT,SPARKS AND
FLAME..

Disposal

Waste Disposal Methods:INCINERATE IN EPA PERMITTED FACILITY.
CONTAMINATED ABSORBANT MAY BE DISPOSED OF IN A HAZARDOUS WATER
LANDFILL. DISPOSE IAW FED/ST/LOCAL REGULATIONS. DO NOT INCINERATE
CLOSED CONTAINERS. OBSERVE PRECAU TIONS FOR DISPOSAL OF FLAMMABLE
MATERIALS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.