Product ID:SCOTCH-WELD (R) 1751-B, ID 62-1751-0530-3
MSDS Date:12/30/1988
FSC:8040
NIIN:00-307-5925
Kit Part:Y
MSDS Number: BHDLF

3M GENERAL OFFICES

3M CENTER
ST. PAUL, MN 55144-1000
US

Emergency Phone: 612-733-1110

Info Phone: 612-733-1110

Cage: 1BY21

MINNESOTA MINING AND MFG CO ENGINEERING DOCUMENT SYSTEMS

SAINT PAUL, MN 55144-1000 US

Telephone: 612-737-4114

Cage: 1BY21

EPOXY RESIN

CAS: 25068-38-6

RTECS: KC2100000

Fraction By Weight: 50-60%

OSHA PEL NONE

ACGIH TLV: NONE

ALUMINUM (SARA III)

CAS: 7429-90-5

RTECS: BD0330000

Fraction By Weight: 30-40%

OSHA PEL 15MG/M3 DUST/5 FUME

ACGIH TLV: 10MG/M3 DUST; 9192

CLAY

CAS: 68953-58-2

Fraction By Weight: 1-10%

OSHA PEL NONE

ACGIH TLV: NONE

SILICA-AMORPHOUS

CAS: 112945-52-5

RTECS: VV7310000

Fraction By Weight: 1-10%

OSHA PEL NONE

ACGIH TLV: NONE

RESORCINOL

CAS: 108-46-3

Fraction By Weight: 1-10%

OSHA PEL NONE

ACGIH TLV: NONE

EPA Report Quantity: 5000 LBS

DOT Report Quantity: 5000 LBS

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYE CONTACT: PRODUCT MAY BE IRRITATING
TO EYES UPON DIRECT CONTACT. SKIN CONTACT: PRODUCT MAY BE
IRRITATING ON PROLONGED/REPEATED CONTACT. EPOXY RESIN INPRODUCT IS
A SKIN SENSITIZER, ESPECIALLY FOR CERTAIN SUSCEPTIBLE
INDIVIDUALS.INHALATION: MAY BE IRRITATING TO NOSE/THROAT.
INGESTION: ORAL TOXICITY IS NEGLI.

First Aid:EYE CONTACT: IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR
AT LEAST 10 MINUTESAND CALL A PHYSICIAN. SKIN CONTACT: WASH
THOROUGHLY WITH SOAP AND WATER. INHALATION: REMOVE PERSON TO
FRESH AIR. CALL A PHYSICIAN. IF SWALLOWED: DO NOTINDUCE VOMITING.
IMMEDIATELY CALL A PHYSICIAN OR POISON CONTROL CENTER.

Autoignition Temp:Autoignition Temp Text:N/D
Extinguishing Media:CO2, FOAM, DRY CHEMICALS, WATER
Fire Fighting Procedures:FIRE FIGHTERS SHOULD BE EQUIPPED WITH
SELF-CONTAINED BREATHING APPARATUS WHEN FIGHTING FIRES INVOLVING
THIS MATERIAL.
Unusual Fire/Explosion Hazard:NONE

Spill Release Procedures:VENTILATE THE AREA. OBSERVE ALL PRECAUTIONS
FROM OTHER SECTIONS. COLLECT SPILLED MATERIALS. PLACE IN A U.S.
DEPARTMENT OF TRANSPORTATION-APPROVED METAL CONTAINER, AND SEAL.

Other Precautions:AVOID BREATHING VAPORS RELEASED DURING HEAT CURING.
CURING OVENS S/B PROPERLY VENTED TO OUTDOORS/SUITABLE EMISSION
CONTROL DEVICE. AVOID EYE CONTACT WITH OR BREATHING DUST FM
CUTTING/GRINDING/SANDI NG ON CURED MATERIAL. WASH CONTAM CLOTH.

Ventilation:USE ONLY WITH SUFFICIENT VENTILATION TO MAINTAIN VAPOR
CONCENTRATIONS BELOW RECOMMENDED EXPOSURE LIMITS.
Protective Gloves:WEAR IMPERVIOUS GLOVES.
Eye Protection:WEAR SAFETY GLASSES OR GOGGLES
Other Protective Equipment:DUST MASK TO AVOID DUST EXPOSURE.
Work Hygienic Practices:WASH WITH SOAP AND WATER.
Supplemental Safety and Health
KEY1:N1. THIS PRODUCT IS A KIT CONSISTING OF THREE PARTS. PART ONE, HAS
PNI A; PART TWO HAS PNI B, PART THREE HAS PNI C, SAME NSN.

HCC:V7
Spec Gravity:1.300 WATER=1
pH:N/D
Viscosity:PASTE
Solubility in Water:VERY SLIGHT
Appearance and Odor:GRAY, VISCOUS PASTE, LITTLE ODOR.
Percent Volatiles by Volume:0.00

Stability Indicator/Materials to Avoid:YES
Hazardous Decomposition Products:THERMAL DECOMPOSITION OR BURNING MAY
PRODUCE C, H, N DECOMPOSITION PRODUCTS.

Waste Disposal Methods:MIX PART A W/PART B. COMPLETELY CURE/DISPOSE OF
FULLY CURED WASTE PRODUCT IN A SANITARY LANDFILL. INCINERATE
UNCURED BULK PRODUCT AFTER MIXING WITH FLAMMABLE MATERIAL IN AN
INDUSTRIAL/COMMERCIAL FACILITY. DISPOSAL S/B IAW APPLICABLE
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.