BHDND - ENAMEL INTERIOR SG GREEN 24233 ID752426

  • MSDS: BHDND
  • Manufacturer: PRATT AND LAMBERT INC
  • Product Name: ENAMEL INTERIOR SG GREEN 24233 ID752426
  • National Stock Number: 8010-00-558-5799
Product Identification

Product ID:ENAMEL INTERIOR SG GREEN 24233 ID752426
MSDS Date:06/05/1989
FSC:8010
NIIN:00-558-5799
MSDS Number: BHDND

Responsible Party
PRATT & LAMBERT, INC.
16116 E 13TH ST
WICHITA, KS 67201
US

Preparer: W.A. ELLISON

Cage: FO127

Contractor
PRATT AND LAMBERT INC
22 CLEVELAND, OH 44101-1027 US

Telephone: 216-566-2902

Cage: 61196

Ingredients

MINERAL SPIRITS

CAS: 64742-88-7

Fraction By Weight: 10%

OSHA PEL 500 PPM 2950 MG/CU M

ACGIH TLV: 100 PPM 525 MG/CU M


NEPTANE

Fraction By Weight: 20%

ACGIH TLV: 400 PPM


VOC. ORGANIC CMPD 3.26 LB/GL LESS WATER & NPRS* 391 G/L

RTECS: 9999999VO

Hazards

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SWALLOWING;GASTROINTESTINAL
IRR/NAUSEA/VOMIT/DIARRHEA.ASPIRATION OF MAT'L INTO LUNGS-CHEM
PNEUMONITIS-FATAL.INHALATION:ANESTHETIC.IRR OF NOSE/THROAT/ACUTE
NERVOUS SYS DEPRESSION. CHAR BY HEADACHE , DIZZINESS.
CONFUSION/NAUSEA/UNCONSCIOUSNESS/ASPHYXIATION. EYE: IRRITATION
SKIN: DEFATTING AND IRRITATION.
Effects of Overexposure:PROLONGED AND REPEATED OCCUPATIONAL
OVEREXPOSURE TO SOLVENTS W/PERMANENT BRAIN AND NERVOUS SYSTEM
DAMAGE. INTENTIONAL MISUSE BY DELIVERATELY CONCENTRATING AND
INHALING THE CONTENTS MAY BE HARMFUL OR F ATAL.

First Aid

First Aid:SWALLOWING: DONOT INDUCE VOMITING CALL POISON CONTROL CENTER,
EMERG ROOM. INHALATION: REMOVE TO FRESH AIR IF BREATHING STOPPED
GIVE CPR. EYE: FLUSH W/LG AMTS OFWATER LIFTING LIDS FOR 15 MINUTES.
GET M EDICAL ATTENTION. SKIN: REMOVE CONTAMINATED CLOTHING. WASH
AFFECTED AREA W/SOAP AND WTR. SEEK MEDICAL ATTENTION IF IRRITATION
PERSISTS. PHYSICAN TREATMENT SHOULD BE DIRECTED AT CONTROL OF
SYMPTOM.

Fire Fighting

Flash Point:102F/38.89C
Extinguishing Media:CLASS B FIRE EXTINGUISHERS DESIGNED TO EXTINGUISH
FLAMMABLE LIQUID FIRES. POLYMER FOAM IS PREFERRED FOR LARGE FIRES.
Fire Fighting Procedures:WEAR SELF CONTAINED BREATHING APPARATUS. WATER
MAY BE INNEFECTIVE, BUT MAY BE USED TO PREVENT PRESSURE BUILD-UP.
IF WATER IS USED, FOG NOZZLES ARE PREFERABLE.
Unusual Fire/Explosion Hazard:DURING EMERG CONDITIONS, OVEREXPOSURE TO
DECOMP PRODUCTS MAY CAUSE A HEALTH HAZ.GET MED ATTN.KEEP CONTNR
TIGHTLY CLOSD. MAY EXPLODE WHEN EXPOSED TO EXTREME HEAT

Accidental Release

Spill Release Procedures:KEEP SPECTATORS AWAY. ELIMINATE IGNITION
SOURCES. DIKE AND CONTAIN SPILL W/INERT MATERIAL. TRANSFER LIQUIDS
TO COVERED METAL CONTAINERS FOR RECOVERY. PREVENT CONTAMINATION OF
SEWERS, STREAMS, AND GROU ND MATERAL W/SPILLED MATERIAL.

Handling

Handling and Storage Precautions:DO NOT STORE ABOVE 95F. STORE LARGE
QUANTITIES IN COMPLIANCE WITH OSHA 29CFR1910.106. DO
NOT TAKE INTERNALLY. CLOSE CONTAINER AFTER USE.
Other Precautions:EMPTY CONTAINERS MUST NOT BE WASHED AND RE-USED FOR
ANY PURPOSE. CONTAINERS SHOULD BE GROUNDED AND BONDED TO THE
RECEIVING CONTAINER. DO NOT WELD, BRAZE OR CUT ON EMPTY CONTAINERS.
NEVER USE PRESSURE TO EMPTY. DRUM IS NOT A PRESSURE VESSEL.

Exposure Controls

Respiratory Protection:NOT REQD IN WELL VENTILATED AREAS. RESTRICTED
AREAS A NIOSH APPROVED CHEMICAL CARTRIDGE RESPIRATOR MAYBE REQD.
UNDER CERTAIN COND (SPRAYING) MECHANICAL PREFILTER MAY BE REQD.
Ventilation:PROVIDE GENERAL DILUTION AND LOCAL EXHAUST VENTILATION IN
SUFFICIENT VOLUME AND PATTERN TO MAINTAIN CONCENTRATIONS.
Protective Gloves:SOLVENT IMPERMEABLE GLOVES
Eye Protection:WEAR SAFETY SPECTACLES
Other Protective Equipment:NOT LIKELY NEEDED
Supplemental Safety and Health
NK

Chemical Properties

Boiling Pt:B.P. Text:281-388F
Vapor Density:>THAN AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:44

Stability

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS OR ALKALINE MATERIALS
Stability Condition to Avoid:AVOID EXCESSIVE HEAT AND SOURCES OF
IGNITION.
Hazardous Decomposition Products:BURNING,INCLUDING WHEN HEATED BY
WELDING OR CUTTING, WILL PRODUCE SMOKE, CARBON MONOXIDE AND CARBON
DIOXIDE.
Conditions to Avoid Polymerization:KEEP AWAY FROM HEAT SPARKS AND
FLAME.

Disposal

Waste Disposal Methods:DISPOSE IAW FEDERAL, STATE AND LOCAL LAWS.
OBSERVEPRECAUTIONS FOR DISPOSAL OF FLAMMABLE MATERIAL. DO NOT
INCINERATE IN CLOSED CONTAINERS. PROPER RCRA
CLASSIFICATION WOULD BE D001.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.