BHFVH - TORRSEAL PART A
- MSDS: BHFVH
- Manufacturer: VARIAN ASSOCIATES
- Product Name: TORRSEAL PART A
- National Stock Number: 8030-00-998-3321
Product Identification
Product ID:TORRSEAL PART A
MSDS Date:01/01/1987
FSC:8030
NIIN:00-998-3321
Kit Part:Y
MSDS Number: BHFVH
Responsible Party
PALO ALTO, CA 94303
US
Emergency Phone: 415-493-4000
Info Phone: 415-493-4000
Cage: 99313
Contractor
Cage: 99313
Ingredients
MAGNESIUM SILICATE HYDRATE
CAS: 1343-90-4
RTECS: OM4360000
Fraction By Weight: 46%
ACGIH TLV: 2 MG/M3
BIS PHENOL A-EPICHLORONYDRIN EPOXY RESIN
Fraction By Weight: 50%
TITANIUM DIOXIDE
CAS: 13463-67-7
RTECS: XR2275000
Fraction By Weight: 2 - 10%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3 TDUST; 9293
Hazards
Routes of Entry: Inhalation:NO Skin:NO Ingestion:NO
Effects of Overexposure:CONTACT WITH SKIN OR EYES MAY CAUSE IRRITATION.
First Aid
First Aid:IN CASE OF SKIN CONTACT WASH WITH SOAP AND WATER AT FIRST
OPPORTUNITY. IN CASE OF EYE CONTACT FLUSH WITH COPIOUS AMOUNTS OF
WATER FOR 15 MINUTES.
Fire Fighting
Flash Point Method:COC
Flash Point:470F / 243.33C
Extinguishing Media:CO2 FOAM OR DRY CHEMICAL
Fire Fighting Procedures:NONE
Unusual Fire/Explosion Hazard:NONE
Accidental Release
Spill Release Procedures:SCRAPE UP, TRANSFER TO METAL CONTAINER.
SOLVENTS MAY BE NECESSARY TO CLEAN UP STICKY RESIDUE, BUT OBSERVE
HEALTH AND FIRE HAZARDS OF SOLVENT.
Handling
Handling and Storage Precautions:STORE AWAY FROM DIRECT HEAT, WHICH
MIGHT CAUSE PHYSICAL SEPERATION OF FILLER.
Exposure Controls
Respiratory Protection:NONE REQUIRED
Ventilation:LOCAL EXHAUST ONLY IF HEATED
Protective Gloves:RUBBER OR PLASTIC
Eye Protection:GOGGLES WHERE THERE IS DANGER OF SPLASH
Other Protective Equipment:NONE REQUIRED
Supplemental Safety and Health
NK
Chemical Properties
Boiling Pt:B.P. Text:NA
Melt/Freeze Pt:M.P/F.P Text:0
Vapor Pres:NIL
Vapor Density:NA
Spec Gravity:1.6
Evaporation Rate & Reference:>1
Solubility in Water:INSOLUBLE
Appearance and Odor:WHITE HIGH VISCOSITY LIQUID, VERY SLIGHT ODOR
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS
Stability Condition to Avoid:NA
Hazardous Decomposition Products:CARBON MONOXIDE, ALDEHYYDES
Conditions to Avoid Polymerization:DO NOT MIX LARGE AMOUNTS OF EPOXY
RESIN WITH DIETHYLENETRIAMINE WITHOUT RECOGNITION OF DEVELOPMENT OF
EXOTHERMIC HEAT.
Disposal
Waste Disposal Methods:THIS IS NOT A HAZARDOUS MATERIAL UNDER THE
RESOURCE CONSERVATION AND RECOVERY ACT. (RCRA).
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.