BHNQN - JOINT SEALER 9028,PART A

Product Identification

Product ID:JOINT SEALER 9028,PART A
MSDS Date:06/30/1986
FSC:8030
NIIN:00N010171
MSDS Number: BHNQN

Responsible Party
KOCH MATERIALS COMPANY (FORMERLY ALLIED CHEMICALS)
WICHITA, KS 67201

Emergency Phone: 316-832-6777

Info Phone: 316-832-6777

Cage: 0TAB0

Contractor
KOCH MATERIALS CO COATINGS/SEALANTS DIV
2338 STROUD, OK 74079-0519 US

Telephone: 918-968-3541

Cage: 0TAB0

Ingredients

RESIN PLASTICIZER

CAS: 68515-40-2

Fraction By Weight: <42%

OSHA PEL N/K

ACGIH TLV: N/K


CALCIUM CARBONATE (MARBLE) (LIMESTONE)

CAS: 1317-65-3

RTECS: EV9580000

Fraction By Weight: <23%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9192


SULFUR

CAS: 7704-34-9

RTECS: WS4250000

Fraction By Weight: <2%

OSHA PEL N/K

ACGIH TLV: N/K


CLAY

CAS: 71011-27-3

Fraction By Weight: <3%

OSHA PEL N/K

ACGIH TLV: N/K


SODIUM BICHROMATE (SARA III)

CAS: 10588-01-9

RTECS: HX7700000

Fraction By Weight: <34%

OSHA PEL 0.1 PPM CRO3;CEILING

ACGIH TLV: 0.05 MG CR/M3; 9192

EPA Report Quantity: 10 LBS

DOT Report Quantity: 10 LBS


CARBON BLACK

CAS: 1333-86-4

RTECS: FF5800000

Fraction By Weight: <2%

OSHA PEL 3.5 MG/M3

ACGIH TLV: 3.5 MG/M3; 9192

Hazards

LD50 LC50 Mixture:N/K
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:PERMANENT EYE INJURY POSSIBLE IF
PRODUCT COMES IN CONTACT WITH EYES.
Explanation of Carcinogenicity:SODIUM BICHROMATE:SUFFICIENT EVID FOR
CARCIN IN HUM,SUFFICIENT EVID FOR CARCIN IN ANIMALS (IARC
1987).CHROMIUM (SEE SUP)
Effects of Overexposure:EYES:MAY CAUSE IRRITATION AND PERMANENT EYE
INJURY.SKIN:MAY CAUSE IRRITATION.PROLONGED OR REPEATED CONTACT MAY
CAUSE CHROME SORES.INGESTION:CAN CAUSE DIGESTIVE SYSTEM
BURNS.INHALATION:VAPOR CAN CAUSE IRRITATION.
Medical Cond Aggravated by Exposure:N/K

First Aid

First Aid:EYES:FLUSH WITH LARGE AMOUNTS OF WATER FOR AT LEAST 15 MIN
WHILE HOLDING THE EYELIDS OPEN.GET MEDICAL ATTENTION.SKIN:WASH WITH
SOAP AND WATER OR USE WATERLESS HAND CLEANER.DO NOT USE SOLVENTS OR
THINN ERS TO CLEAN THE SKIN.INGEST:IF VICTIM IS CONSCIOUS GIVE
LIQUIDS.INDUCE VOMITING.GET MED ATTENTION.INHAL:MOVE TO SOURCE OF
FRESH AIR.IF BRTHG IS DFCLT,GIVE O*2..IF BRTHG HAS STOPPED GIVE
ARTF RESP.

Fire Fighting

Flash Point Method:OC
Flash Point:445F FOR RESIN
Extinguishing Media:USE DRY CHEMICAL,WATER FOG,FOAM,CARBON DIOXIDE.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:HAZARDOUS DECOMPOSITION PRODUCTS MAY
INCLUDE CARBON MONOXIDE,CARBON DIOXIDE,OXIDES OF
SULFUR,ALDEHYDES,AND OTHER UNIDENTIFIED COMPOUNDS.

Accidental Release

Spill Release Procedures:DIKE OR CONTAIN SPILL WITH EARTH,FLOOR
DRY,SAND,ETC.PUMP LIQUID TO CONTAINERS OR STORAGE VESSEL.SOAK UP
RESIDUE WITH ABSORBENT MATERIAL.SCOOP CONTAMINATED ABSORBENT AND
DIKING MATERIAL INTO CONTAINERS FOR DISPOSAL.
Neutralizing Agent:N/K

Handling

Handling and Storage Precautions:STORE BETWEEN 60F AND 100F.STORAGE
BELOW 60F WILL NOT DAMAGE THE PRODUCT,HOWEVER,IT MUST BE WARMED
BEFORE USE.
Other Precautions:N/K

Exposure Controls

Respiratory Protection:NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR
EXPOSURE OF CONCERN .
Ventilation:NORMAL VENTILATION IS USUALLY ADEQUATE.
Protective Gloves:IMPERV GLOVES SUCH AS NEOPRENE OR RUBBER
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:WEAR A PROTECTIVE APRON IF REPEATED CONTACT
IS LIKELY.
Work Hygienic Practices:N/K
Supplemental Safety and Health
BP:734F FOR THE RESIN PLASTICIZER.VP:0.5 MMHG @ 392F FOR THE RESIN
PLASTICIZER.EXPLAN OF CARCIN:AND CERTAIN CHROMIUM COMPOUNDS:KNOWN
HUMAN CARCINOGEN (NTP,1985).

Chemical Properties

Boiling Pt:B.P. Text:SEE SUPP
Melt/Freeze Pt:M.P/F.P Text:N/K
Decomp Temp:Decomp Text:N/K
Vapor Pres:SEE SUPP
Spec Gravity:1.47 (WATER=1)
Solubility in Water:SLIGHT
Appearance and Odor:HEAVY PASTE.

Stability

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDIZERS.
Stability Condition to Avoid:N/K
Hazardous Decomposition Products:CARBON MONOXIDE,CARBON DIOXIDE,OXIDES
OF SULFUR,ALDEHYDES,AND OTHER UNIDENTIFIED COMPOUNDS.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

Disposal

Waste Disposal Methods:WASTE SHOULD BE DISPOSED OF ACCORDING TO
LOCAL,STATE AND FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.