BJMVW - SID F 151-155 B COMP F-09P1001

  • MSDS: BJMVW
  • Manufacturer: SEAGRAVE COATINGS CORP OF VA
  • Product Name: SID F 151-155 B COMP F-09P1001
  • National Stock Number: 8010-00-104-9702
Product Identification

Product ID:SID F 151-155 B COMP F-09P1001
MSDS Date:10/09/1990
FSC:8010
NIIN:00-104-9702
Kit Part:Y
MSDS Number: BJMVW

Responsible Party
SEAGRAVE COATINGS CORP OF VA
4030 SEAGUARD AVENUE
PORTSMOUTH, VA 23701
US

Emergency Phone: 804-488-4411

Info Phone: 804-488-4411

Preparer: NSO

Cage: 60163

Contractor
SHERWIN-WILLIAMS, SEAGUARD
PORTSMOUTH, VA 23704 US

Telephone: 757-397-2223

Cage: 60163

Ingredients

AROMATIC HYDROCARBON 100 (VP 2.7 MMHG @ 20C)

CAS: 64742-95-6

Fraction By Weight: 25%

ACGIH TLV: 200 PPM


EPOXY RESIN

CAS: 25068-38-6

RTECS: SL6475000

Fraction By Weight: 50%

Hazards

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:INHALATION: IRRITATION TO RESPIRATORY
TRACT, HEADACHE, DIZZINESS AND NAUSEA. SKIN CONTACT: PRIMARY
IRRITATION. EYE CONTACT: PRIMARY IRRITATION.
Effects of Overexposure:INHALATION: IRRITATION TO RESPIRATORY TRACT,
HEADACHE, DIZZINESS AND NAUSEA. SKIN CONTACT: PRIMARY IRRITATION.
EYE CONTACT: PRIMARY IRRITATION.
Medical Cond Aggravated by Exposure:PRE-EXISTING SENSITIVITY TO
SOLVENTS CAN CAUSE A HEIGHTENED REACTION TO EXPOSURE TO THIS
PRODUCT.

First Aid

First Aid:INHALATION: REMOVE TO FRESH AIR, RESTORE BREATHING. CONSULT A
PHYSICIAN. SKIN CONTACT: FLUSH WITH WATER. EYE CONTACT: FLUSH
IMMEDIATELY WITH LARGE AMOUNTS OF WATER. CONSULT A PHYSICIAN.

Fire Fighting

Flash Point Method:TCC
Flash Point:114 F/46 C
Lower Limits:0.5
Upper Limits:6.0
Extinguishing Media:DRY CHEMICAL, CARBON DIOXIDE, FOAM, WATER FOG.
Fire Fighting Procedures:WATER MAY BE USED TO COOL CLOSED CONTAINERS TO
PREVENT PRESSURE BUILD-UP AND POSSIBLE AUTOIGNITION OR EXPLOSION
WHEN EXPOSED TO EXTREME HEAT.
Unusual Fire/Explosion Hazard:KEEP CONTAINERS TIGHTLY CLOSED. ISOLATE
FROM HEAT, SPARKS AND OPEN FLAME. CLOSED CONTAINERS MAY EXPLODE
WHEN EXPOSED TO EXTREME HEAT.

Accidental Release

Spill Release Procedures:AVOID BREATHING SOLVENT VAPORS. ENSURE
ADEQUATE VENTILATION. AVOID SPARKS, FLAMES AND ANYTHING WHICH COULD
CAUSE FIRE.

Handling

Handling and Storage Precautions:STORE IN A COOL, DRY AREA WITH
VENTILATION SUITABLE FOR STORING MATERIALS SHOWN IN THIS MSDS.
Other Precautions:PROVIDE RESPIRATORY PROTECTION AGAINST FUMES
GENERATED DURING BURNING.

Exposure Controls

Respiratory Protection:NIOSH/OSHA APPROVED RESPIRATOR TYPES SUITABLE
FOR MATERIALS, RECOMMENDED. APPROVED CHEMICAL/MECHANICAL FILTERS
RECOMMENDED WHEN VENTILATION IS RESTRICTED APPROVED AIRLINE TYPE
RESPIRATORS OR HOODS REC OMMENDED IN CONFINED AREAS.
Ventilation:SUFFICIENT VENTILATION, IN VOL/PATTERN TO KEEP AIR
CONTAMINATION BELOW CURRENT APPLICABLE OSHA/ACGIH PERMISSIBLE
LIMITS
Protective Gloves:RECOMMENDED FOR PROLONG/REPEATED CONTACT
Eye Protection:CHEM GOGGLES W/SIDE SHIELDS/FACE SHIELDS
Other Protective Equipment:USE PROTECTIVE CREAMS WHERE SKIN CONTACT IS
LIKELY. REMOVE AND WASH CONTAMINATED CLOTHING BEFORE REUSE.
Work Hygienic Practices:WASH HANDS BEFORE EATING OR SMOKING. SMOKE IN
DESIGNATED AREAS ONLY.
Supplemental Safety and Health

Chemical Properties

Boiling Pt:B.P. Text:313 TO 355F
Evaporation Rate & Reference:IS SLOWER THAN ETHER
Solubility in Water:INSOLUBLE
Appearance and Odor:MILKY BROWN LIQUID WITH AROMATIC SOLVENT
Percent Volatiles by Volume:35.8

Stability

Stability Indicator/Materials to Avoid:YES
Stability Condition to Avoid:PRODUCT IS STABLE UNDER NORMAL CONDITIONS.
AS WITH ANY OTHER ORGANIC MATERIAL, COMBUSTION WILL PRODUCE CO2 &
PROBABLY CO
Hazardous Decomposition Products:OXIDIZING MATERIALS CAN CAUSE A
VIGOROUS REACTION.
Conditions to Avoid Polymerization:WILL NOT OCCUR UNDER NORMAL
CONDITIONS.

Disposal

Waste Disposal Methods:SOAK LIQUIDS WITH SAWDUST OR RAGS AND REMOVE.
FLUSH WITH WATER IF POSSIBLE. AVOID SKIN CONTACT. DISPOSAL SHOULD
BE IN ACCORDANCE WITH LOCAL, STATE AND FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.