BLBCM - PURPLE IMFLO GLOSS ENAMEL, 17100 860
- MSDS: BLBCM
- Manufacturer: ROSE TALBERT PAINT COMPANY
- Product Name: PURPLE IMFLO GLOSS ENAMEL, 17100 860
- National Stock Number: 8010-01-040-3761
Product Identification
Product ID:PURPLE IMFLO GLOSS ENAMEL, 17100 860
MSDS Date:09/19/1990
FSC:8010
NIIN:01-040-3761
MSDS Number: BLBCM
Responsible Party
CAYCE, SC 29033
US
Emergency Phone: 803-796-0324
Info Phone: 803-796-0324
Preparer: DAVID KELLY
Cage: 0CUY5
Contractor
Telephone: 803-796-0324
Cage: 0CUY5
Ingredients
TITANIUM DIOXIDE
CAS: 13463-67-7
RTECS: XR2275000
Fraction By Weight: 3.03%
OSHA PEL 15 MG/M3 TDUST
ACGIH TLV: 10 MG/M3 TDUST; 9293
STODDARD SOLVENT
CAS: 8052-41-3
RTECS: WJ8925000
Fraction By Weight: 47.57%
OSHA PEL 500 PPM
ACGIH TLV: 100 PPM; 9293
4.007
RTECS: 9999999VO
Hazards
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:PERMANENT BRAIN & NERVOUS SYSTEM
DAMAGE FROM SOLVENTS. CENTRAL NERVOUS SYSTEM DEPRESSION FROM
MINERAL SPIRITS (DIZZINESS, HEADACHE, INTOXICATION/EUPHORIA,
UNCONSCIOUSNESS). IRRITATION TO UPPER RESPIRA TORY TRACT,
GASTROINTESTINAL TRACT, NOSE, THROAT, EYE AND SKIN. POSSIBLE
PULMONARY EDEMA. SKIN DEFATTING.
Explanation of Carcinogenicity:THIS PRODUCT CONTAINS NO REPORTED
CARCINOGENS OR SUSPECTED CARCINOGENS.
First Aid
First Aid:EYE: FLUSH WITH LUKEWARM WATER FOR 15 MINUTES. SKIN: FLUSH
WASH W/COPIOUS AMTS OF LUKEWARM WATER. REMOVE CONTAMINATED CLOTHES
PROMPTLY. INHALE: REMOVE TO FRESH AIR. RESTORE BREATHING. INGEST:
RINSE MO UTH IMMEDIATELY. GIVE VICTIM 6 TO 8 OZ OF LIQUID. (NEVER
GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON). DO NOT INDUCE
VOMITING UNLESS ADVISED BY DR. CONTACT PHYSICIAN IMMEDIATELY FOR
ANY EMERGENCY.
Fire Fighting
Flash Point Method:TCC
Flash Point:107F,42C
Lower Limits:.7
Upper Limits:6.0
Extinguishing Media:USE CO2, DRY CHEMICAL FOAM EXTINGUISHER. NFPA CLASS
B EXTINGUISHER FOR NFPA CLASS 1B FLAMMABLE LIQUID FIRES.
Fire Fighting Procedures:WATER SPRAY MAY BE INEFFECTIVE, USE TO COOL
CLOSED CNTNRS TO PREVENT PRESSURE BUILDUP & EXPLOSION WHEN EXPOSED
TO EXTREME HEAT. FOG NOZZLES ARE PREFERABLE.
Unusual Fire/Explosion Hazard:KEEP CONTAINERS CLOSED. ISOLATE FROM
HEAT, ELEC EQUIP, SPARKS & OPEN FLAME. DO NOT APPLY TO HOT
SURFACES. NEVER USE WELDING OR CUTTING TORCH ON OR NEAR CNTNRS.
Accidental Release
Spill Release Procedures:STAY UPWIND, AWAY FROM SPILL. WEAR PROTECTIVE
EQUIPMENT. STOP/CONTAIN DISCHARGE. KEEP IGNITE SOURCES AWAY.
VENTILATE AREA. USE NON-SPARKING TOOLS. COVER W/INERT MATERIAL TO
REDUCE FUMES. KEEP FROM DRA INS, SEWERS, WATERWAYS. CONTACT FIRE
AUTHORITIES.*
Neutralizing Agent:*CALL HEALTH/POLLUTION CONTROL AGENCIES; SPILL
RESPONSE TEAMS IF LARGE SPILL.
Handling
Handling and Storage Precautions:KEEP COOL, DRY, AWAY FROM IGNITION.
USE & STORE IN ADEQUATE VENTILATION. DO NOT SMOKE IN STORAGE AREA.
AVOID INHALE OF VAPORS & CONTACT W/PRODUCT.
Other Precautions:CONTAINERS OF MATERIAL MAY BE HAZARDOUS WHEN EMPTIED.
SINCE EMPTIED CNTNRS RETAIN PRODUCT RESIDUES (VAPOR, LIQUID AND/OR
SOLID), ALL HAZARD PRECAUTIONS GIVEN TO BE OBSERVED. INTENTIONAL
MISUSE BY CONC ENTRATING/INHALING MAY BE HARMFUL/FATAL.
Exposure Controls
Respiratory Protection:OPEN AREAS: NIOSH/MSHA APPR'D MECHANICAL FILTER
RESPIRATOR FOR SOLID AIRBORNE PARTICLES DURING SPRAYING, ETC.
RESTRICT AREA: NIOSH/MSHA APPR'D CHEMICAL-MECHANICAL FILTERS FOR
COMBO OF PARTIC/GAS/VAPOR . CONFINED: AIR LINE RESPIRATOR OR HOOD.
Ventilation:PROVIDE GENERAL DILUTION OR LOCAL EXHAUST VENTILATION IN
VOLUME/PATTERN TO KEEP TLV & LEL BELOW ACCEPTABLE LIMITS.
Protective Gloves:NATURAL RUBBER, NEOPRENE, BUNA N,NITRILE
Eye Protection:GOGGLES, SAFETY EYEWEAR W/SIDESHIELDS
Other Protective Equipment:AN APRON SHOULD BE WORN TO AVOID SKIN
CONTACT. SAFETY SHOWER AND EYE BATH SHOULD BE READILY AVAILABLE.
Work Hygienic Practices:WASH THOROUGHLY BEFORE EATING OR USING
WASHROOM. DO NOT WEAR CONTAMINATED CLOTHES UNTIL THEY ARE PROPERLY
LAUNDERED.
Supplemental Safety and Health
RESPIRATORY PROTECTION MAY BE NEEDED IN ANY LATER MANUFACTURING
OPERATION IN WHICH THE PRODUCT MAY BECOME AIRBORNE IN THE FORM OF
VAPOR OR DUST. THIS PRODUCT CONTAINS PIGMENTS WHICH MAY BECOME A
DUST NUISANCE WHEN REMOVED BY ABRASIVE BLASTING, SANDING OR
GRINDING.
Chemical Properties
Boiling Pt:B.P. Text:318 TO 383F
Vapor Pres:2.60
Vapor Density:> AIR
Spec Gravity:8.4 LB/GL
Evaporation Rate & Reference:SLOWER THAN BUTYL ACETATE
Solubility in Water:NA
Appearance and Odor:LIQUID
Percent Volatiles by Volume:61.18
Stability
Stability Indicator/Materials to Avoid:YES
THIS PRODUCT IS INCOMPATIBLE WITH STRONG ACIDS.
Stability Condition to Avoid:AVOID EXPOSURE TO SPARKS, OPEN FLAME, HOT
SURFACES AND ALL SOURCES OF HEAT AND IGNITION.
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES WHEN
HEATED TO DECOMPOSITION AS IN WELDING. FUMES MAY CONTAIN CO, CO2,
OXIDES OF NITROGEN.
Disposal
Waste Disposal Methods:DO NOT FLUSH TO SEWER, WATERSHED OR WATERWAY.
DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE AND FEDERAL REGULATIONS.
DO NOT INCINERATE CLOSED CONTAINERS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.