BLLBN - 5 MINUTE EPOXY HARDENER
- MSDS: BLLBN
- Manufacturer: DEVCON CORP
- Product Name: 5 MINUTE EPOXY HARDENER
- National Stock Number: 8040-01-032-4728
Product Identification
Product ID:5 MINUTE EPOXY HARDENER
MSDS Date:08/01/1987
FSC:8040
NIIN:01-032-4728
Kit Part:Y
MSDS Number: BLLBN
Responsible Party
DANVERS, MA 01923
US
Emergency Phone: 617-777-1100
Info Phone: 617-777-1100
Cage: 16059
Contractor
Telephone: 1-508-777-1100
Cage: 16059
Ingredients
2,4,6-TRI(DIMETHYLAMINOMETHYL) PHENOL (DMP 30)
CAS: 90-72-2
RTECS: SN3500000
Fraction By Weight: 10-30%
Hazards
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: DMP 30 CAN BE CORROSIVE TO EYE
TISSUE AND MAY CAUSE PERMANENT EYE INJURY. SKIN: ANIMAL TESTS ON
5-MINUTE EPOXY HARDENER HAVE SHOWN IT TO CAUSE LITTLE OR NO SKIN
IRRITATION. INHALATION: DMP 30 VA POR CAN CAUSE IRRITATION OF THE
RESPIRATORY TRACT. INGESTION: DMP 30 IS SLIGHTLY TOXIC BY
INGESTION; REPORTED SYMPTOMS *
Effects of Overexposure:*ARE FATIGUE, MUSCULAR WEAKNESS, LABORED
BREATHING AND IRRITATION OF GASTROINTESTINAL TRACT.
Medical Cond Aggravated by Exposure:NONE REPORTED
First Aid
First Aid:EYES: IMMEDIATELY FLUSH WITH CLEAR WATER FOR 15 MINUTES,
HOLDING LIDS GENTLY OPEN. GET MEDICAL ATTENTION. SKIN: WASH
THOROUGHLY WITH SOAP AND WATER. REMOVE CONTAMINATED CLOTHING AND
SHOES. GET MEDICAL ATTENTION IF IRRITATION DEVELOPS OR PERSISTS.
INGESTION: CONTACT A PHYSICIAN. DO NOT INDUCE VOMITING. INHALATION:
REMOVE TO FRESH AIR.
Fire Fighting
Flash Point Method:TOC
Flash Point:300F,149C
Extinguishing Media:CO2, FOAM OR DRY CHEMICAL.
Fire Fighting Procedures:FIRE FIGHTERS SHOULD WEAR SELF-CONTAINED
BREATHING APPARATUS AND PROTECTIVE CLOTHING.
Unusual Fire/Explosion Hazard:NONE
Accidental Release
Spill Release Procedures:ABSORB SPILLAGE ON INERT MATERIAL AND DISCARD
IN SUITABLE CONTAINERS.
Handling
Handling and Storage Precautions:KEEP HANDS AWAY FROM EYES WHEN
HANDLING MATERIAL OR BEFORE WASHING AFTER USE. STORE IN A COOL, DRY
PLACE.
Exposure Controls
Respiratory Protection:NONE NEEDED IN NORMAL USE WITH PROPER
VENTILATION.
Ventilation:GENERAL MECHANICAL IS SATISFACTORY. IF ODOR IS
DISAGREEABLE, USE LOCAL EXHAUST.
Protective Gloves:CHEMICAL RESISTANT RUBBER GLOVES.
Eye Protection:SAFETY GLASSES.
Work Hygienic Practices:WASH THOROUGHLY AFTER USING, PARTICULARLY
BEFORE EATING OR SMOKING.
Supplemental Safety and Health
Chemical Properties
Vapor Pres:<<1 @ 70F
Spec Gravity:0.97
pH:9.5
Solubility in Water:NIL
Appearance and Odor:LIGHT AMBER LIQUID, SULFUROUS ODOR.
Percent Volatiles by Volume:0
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:EXPOSURE TO OPEN FLAME OR EXCESSIVE HEAT.
Hazardous Decomposition Products:OXIDES OF CARBON, SULFUR AND NITROGEN.
Conditions to Avoid Polymerization:HEAT IS GENERATED WHEN MIXED WITH
EPOXY RESIN. USE CAUTION WHEN MIXING LARGE QUANTITIES.
Disposal
Waste Disposal Methods:REMOVE TO A WASTE DISPOSAL FACILITY OPERATING IN
COMPLIANCE WITH STATE AND LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.