BMCMN - INSTANT ADHESIVE, 3200 SERIES
- MSDS: BMCMN
- Manufacturer: NORTHWEST SCREEN SYSTEMS
- Product Name: INSTANT ADHESIVE, 3200 SERIES
- National Stock Number: 8040-00N025439
Product Identification
Product ID:INSTANT ADHESIVE, 3200 SERIES
MSDS Date:11/01/1985
FSC:8040
NIIN:00N025439
MSDS Number: BMCMN
Responsible Party
MINNEAPOLIS, MN 55406
US
Emergency Phone: 612-729-7365
Info Phone: 612-729-7365
Preparer: ALVIN E. PUDER
Cage: NWEST
Contractor
Telephone: 612-729-7365
Cage: NWEST
Ingredients
REMOVE TO FRESH AIR. SUPPORT BREATHING (GIVE
RTECS: 9999999ZZ
A BURN. BURNS SHOULD BE TREATED NORMALLY AFTER LUMP
RTECS: 9999999ZZ
ETHYL CYANOACRYLATE
Fraction By Weight: 90%+
POLYMETHYLMETHACRYLATE; (POLY (METHYL METHACRYLATE))
CAS: 9011-14-7
RTECS: TR0400000
Fraction By Weight: <10%
HYDROQUINONE
CAS: 123-31-9
RTECS: MX3500000
Fraction By Weight: <0.05%
OSHA PEL 2 MG/M3
ACGIH TLV: 2 MG/M3
EPA Report Quantity: 1 LB
DOT Report Quantity: 1 LB
FURTHER ACTION IN 1-4 DAYS. THERE WILL BE NO
RTECS: 9999999ZZ
CYANOACRYLATES GIVE OFF HEAT ON
RTECS: 9999999ZZ
Hazards
LD50 LC50 Mixture:LD50: ORAL >5000 MG/KG
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:BONDS SKIN RAPIDLY AND STRONGLY. SKIN
AND EYE IRRITANT. LARGE DROP WILL INCREASE TEMP ENOUGH TO CAUSE A
BURN. VAPOR IS IRRIT TO THE EYES AND MUCOUS MEMBRANES ABOVE TVL.
CYANOACRYLATE INTRODUCED INTO E YES WILL ATTACH ITSELF TO EYE
PROTEIN &WILL DISASSOCIATE FROM IT OVER INTERMITTENT PERIODS
COVERING (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: SEVERAL HOURS. THIS WILL CAUSE
PERIODS OF WEEPING OVER SEVERAL HOURS UNTIL CLEARANCE IS ACHIEVED.
NO CHRONIC AFTER-EFT. DOUBLE VISION MAY BE EXPERIENCED TOGETHER
W/LACHRYMATORY EFT. PURE POL Y(METHYL METHACRYLATE) HAS BEEN SHOWN
TO CAUSE TUMORS IN EXPERIMENTAL ANIMALS WHEN IMPLANTED BENEATH THE
SKIN.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:INGEST:ADHESIVE SOLIDIFIES & ADHERES IN MOUTH. SALIVA WILL
LIFT ADHESIVE IN 1/2 TO 2 DAYS. IN CASE LUMP FORMS IN MOUTH,
POSITION PATIENT SO LUMP DOES NOT CAUSE CHOKING WHEN IT DETACHES.
IF LIPS ARE AC CIDENTALLY STUCK TOGETHER APPLY LOTS OFWARM WATER TO
LIPS & ENCOURAGE MAX WETTING/PRESS FROM SALIVA INSIDE MOUTH.
PEEL/ROLL LIPS APART. DO NOT TRY TO PULL LIPS APART. SKIN: IMMERSE
BONDED (SUPP DATA)
Fire Fighting
Flash Point Method:TCC
Flash Point:200F,93C
Extinguishing Media:CO*2, FOAM, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE.
Accidental Release
Spill Release Procedures:FLOOD WITH WATER TO POLYMERIZE. SOAK UP WITH
INERT ABSORBENT.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:STORE AT OR BELOW 75F TO MAXIMIZE
SHELF LIFE. AVOID CONTACT WITH SKIN AND EYES. AVOID BREATHING
VAPOR.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.
Exposure Controls
Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE
FOR EXPOSURE OF CONCERN .
Ventilation:PROVIDE ADEQUATE LOCAL VENTILATION TO MAINTAIN VAPOR
CONCENTRATION BELOW TVL.
Protective Gloves:POLYETHYLENE GLOVES RECOMMENDED.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:DO NOT USE COTTON GLOVES.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
FIRST AID PROC: SURFS IN WARM SOAPY WATER. PEEL/ROLL SURFS APART W/AID
OF BLUNT EDGE, E.G. SPATULA/TEASPOON HANDLE; THEN REMOVE ADHESIVE
FROM SKIN W/SOAP & WATER. DO NOT TRY TO PULL APART. EYES: IN EV ENT
EYELIDS STUCK TOGETHER/BONDED TO EYEBALL, WASH THORO W/WARM WATER &
APPLY GAUZE PATCH. EYE WILL OPEN W/OUT (ING 4)
Chemical Properties
HCC:N1
Boiling Pt:B.P. Text:300F,149C
Vapor Pres:<0.02 @75F
Vapor Density:3
Spec Gravity:1.05 @ 75F
Solubility in Water:POLYMERIZED BY WATER
Appearance and Odor:CLEAR LIQUID W/SHARP IRRITATING ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
POLYMERIZED BY CONTACT WITH WATER, ALCOHOLS, AMINES, ALKALIS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:NONE. THERMAL DECOMP: IRRITATING
ORGANIC FRAGMENTS.
Disposal
Waste Disposal Methods:POLYMERIZE AS ABOVE. LANDFILL OR INCINERATE IN
ACCORDANCE WITH EPA, LOCAL, STATE, AND FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.