BMGYT - PUROLITE A-310 ANION ION EXCHANGE RESIN-B

  • MSDS: BMGYT
  • Manufacturer: BRO TECH CORP DBA PUROLITE CO
  • Product Name: PUROLITE A-310 ANION ION EXCHANGE RESIN-B
  • National Stock Number: 6130-01-060-3679
Product Identification

Product ID:PUROLITE A-310 ANION ION EXCHANGE RESIN-B
MSDS Date:01/01/1990
FSC:6130
NIIN:01-060-3679
MSDS Number: BMGYT

Responsible Party
BRO TECH CORP DBA PUROLITE CO
3620 G ST
PHILADELPHIA, PA 19134
US

Emergency Phone: 215-668-9090

Info Phone: 215-668-9090

Cage: 0A5A0

Contractor
VAPONICS INC
ROCKLAND, MA 02370 US

Telephone: 617-982-9900

Cage: 34203

Ingredients

"NOT HAZARDOUS"

Fraction By Weight: 100%

Hazards

Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE-EYES:MAY CAUSE MECHANICAL
IRRITATION. CHRONIC- NONE KNOWN.
Effects of Overexposure:EYE IRRITATION.
Medical Cond Aggravated by Exposure:EYE DISORDERS

First Aid

First Aid:GET MEDICAL ATTENTION IF SYMPTOMS PERSIST.EYE/SKIN:FLUSH WITH
WATER FOR 15 MINUTES.HOLD EYELIDS OPEN.INHALED:REMOVE TO FRESH
AIR.ORAL:FLUSH OUT MOUTH WITH WATER.SEEK MEDICAL ATTENTION.

Fire Fighting

Flash Point:NONE
Extinguishing Media:CO2, WATER FOG OR DRY CHEMICAL. WATER SPRAY MAY BE
USED TO KEEP FIRE EXPOSED CONTAINERS COOL & FLUSH SPILLS AWAY.
Fire Fighting Procedures:WEAR FULL PROTECTIVE CLOTHING AND
NIOSH-APPROVED SELF-CONTAINED BREATHING APPARATUS WITH FULL
FACEPIECE OPERATED IN THE POSITIVE PRESSURE MODE.
Unusual Fire/Explosion Hazard:NONE

Accidental Release

Spill Release Procedures:RESIN BEADS ON FLOOR MAY MECHANICALLY CAUSE
FLOOR TO BE SLIPPERY. USE CARE TO AVOID FALLS. SWEEP UP AND
TRANSFER TO CONTAINERS FOR RECOVERY OR DISPOSAL.
Neutralizing Agent:NOT APPLICABLE.

Handling

Handling and Storage Precautions:STORAGE-KEEP DRUMS AND PLASTIC BAGS
SEALED TO PREVENT DRYING OR MOISTURE LOSS.
Other Precautions:STORE BELOW 49C (120F) AND ABOVE 0C (32F). DO NOT
RAISE DUST. AVOID CONTACT WITH EYES AND SKIN. AVOID BREATHING DUST.
WASH THOROUGHLY AFTER HANDLING MATERIAL.

Exposure Controls

Respiratory Protection:NONE NORMALLY REQUIRED. IF WORKPLACE EXPOSURE
LIMIT IS EXCEEDED, A NIOSH/MSHA APPROVED AIR SUPPLIED RESPIRATOR OR
DUST RESPIRATOR IS ADVISED.
Ventilation:PROVIDE SUFFICIENT MECHANICAL (GENERAL AND/OR LOCAL
EXHAUST) VENTILATION TO GET RID OF TRI-METHYLAMINE ODOR.
Protective Gloves:NONE
Eye Protection:DUST-RESISTANT SAFETY GOGGLES
Other Protective Equipment:EYE WASH STATION, EMERGENCY SHOWER
Work Hygienic Practices:OBSERVE GOOD PERSONAL HYGIENE PRACTICES AND
RECOMMENDED PROCEDURES.
Supplemental Safety and Health
COMPANY MAKES TWO KINDS OF ION EXCHANGE RESIN (CARTRIDGE). FOR OTHER
KIND, SEE PIN A, SAME NSN.

Chemical Properties

HCC:N1
Spec Gravity:1.11
Solubility in Water:INSOLUBLE
Appearance and Odor:AMBER BEIGE SPHERICAL BEADS WITH AMINE ODOR WHEN
NEW

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS AND CONCENTRATED NITRIC ACID
Stability Condition to Avoid:FLAMES AND TEMPERATURES ABOVE 428F.
Hazardous Decomposition Products:CO, CO2, STYRENE, -N (CH2OH), NH3,
DIVINYLBENZENE

Disposal

Waste Disposal Methods:CAN BE DISPOSED AS ORDINARY TRASH.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.