Product ID:X-5363
MSDS Date:10/10/1990
FSC:8010
NIIN:00-530-5559
MSDS Number: BNCDX

FARWEST PAINT MANUFACTURING CO.

4522 S. 133RD ST.
TUKWILA, WA 98168
US

Emergency Phone: 206-941-1619

Info Phone: 206-244-8844

Preparer: MIKE L. HARRIS

Cage: 2F266

FARWEST PAINT MANUFACTURING CO

TUKWILA, WA 98168 US

Telephone: 206-244-8844

Cage: 2F266

PIGMENT

Fraction By Weight: 5-10%

RESIN/VEHICLE (VAPOR PRESSURE 2.0 MM HG @ 68 F)

Fraction By Weight: 30-35%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM

SOLVENT/MINERAL SPIRITS (VAPOR PRESSURE 2.0 MM HG @ 78 F)

CAS: 8052-41-3

RTECS: WJ8925000

Fraction By Weight: 54-59%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM; 9293

METAL SOAP DRIERS (VAPOR PRESSURE 2.0 MM HG @ 68 F)

Fraction By Weight: < 2%

OSHA PEL 500 PPM

ACGIH TLV: 100 PPM

ADDITIVES AND OTHER INGREDIENTS

Fraction By Weight: < 1%

Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Explanation of Carcinogenicity:NO
Effects of Overexposure:EYES: SEVERE IRRIT/REDNESS/TEARING/BLURRED
VISION. SKIN: MOD IRRIT/DEFATTING/DERMATITIS. INHAL:
NASAL/RESPIRATORY
IRRIT/DIZZINESS/WEAKNESS/FATIGUE/NAUSEA/HEADACHE/POSSIBLE
UNCONSCIOUSNESS/ ASPHYXIATIO N. INGEST: GASTROINTESTINAL
IRRIT/NAUSEA/VOMITING/DIARRHEA. ASPIR OF MAT'L INTO LUNG CAN CAUSE
CHEM PNEUMONITIS (FATAL).

First Aid:SKIN: WASH EXPOSED AREA W/SOAP & WTR. RMV CONTAM CLOTHING,
LAUNDER BEFORE RE-USE. EYES: FLUSH W/LG AMOUNTS OF WTR, LIFTING
UPR/LWR LIDS OCCASIONALLY, GET MED AID. INGEST: DONT INDUCE
VOMITING. KEEP WA RM/QUIET. GET MED AID. ASPIR OF MAT'L INTO LUNGS
DUE TO VOMITING CAN BE FATAL. INHAL: RMV TO FRESH AIR. DIFFICULT
BREATH-ADMIN OXYGEN. BREATHING STOPPED-GIVE ARTIFICIAL RESP. KEEP
QUIET, GET MED AID.

Flash Point Method:TCC
Flash Point:100F,38C
Lower Limits:1.0
Extinguishing Media:FOAM, CO2, DRY CHEMICAL.
Fire Fighting Procedures:SELF-CONTAINED BREATHING APPARATUS WITH A FULL
FACEPIECE OPERATED IN PRESSURE-DEMAND (EVEN JUST RESIDUE) CAN
IGNITE EXPLOSIVELY.
Unusual Fire/Explosion Hazard:NEVER USE NEAR OR AROUND WELDERS OR
CUTTING TORCHES. DRUM (EVEN EMPTY) BECAUSE PRODUCT (EVEN JUST
RESIDUE) CAN IGNITE EXPLOSIVELY.

Spill Release Procedures:SMALL: ABSORB LIQ ON PAPER/VERMICULITE/FLOOR
ABSORB/OTHER ABSORB MAT'L & TRANSFER TO HOOD. LG: ELIM ALL IGNIT
SOURCES (FLARES/FLAMES INCLUD PILOT LIGHTS/ELEC SPARKS). EVAC AREA
OF UNPROTECT PERSONS. S TOP SPILL AT SOURCE, DIKE SPILL AREA
TOPREVENT
Neutralizing Agent:N/K SPREADING , PUMP LIQ TO SALVAGE TANK. REMAIN LIQ
MAY BE TAKEN UP ON SAND

Handling and Storage Precautions:CNTNRS OF THIS MATERIAL MAY BE
HAZARDOUS WHEN EMPTIED, SINCE EMPTIED CNTNRS RETAIN PRODUCT
RESIDUES (VAPOR/LIQ AND/ OR SOLID) ALL HAZARD PRECAUTIONS
Other Precautions:N/K CLAY/EARTH/FLOOR ABSORB/OTHER ABSORB MAT'L.
PREVENT RUN-OFF TO SEWERS/STREAMS/OTHER BODIES OF WTR. IF RUN-OFF
OCCURS, NOTIFY PROPER AUTHORITIES AS REQ THAT A SPILL HAS OCCURED.
GIVEN IN THE DATA S HEET MUST BE OBSERVED.

Respiratory Protection:NIOSH/MSHA JOINTLY APPROVED AIR SUPPLIED
RESPIRATOR IS ADVISED IN ABSENCE OF PROPER ENVIRONMENTAL CONTROL.
OSHA REGULATIONS ALSO PERMIT OTHER NIOSH/MSHA RESPIRATORS UNDER
SPECIFIED CONDITIONS.
Ventilation:PROVIDE SUFFICIENT MECHANICAL (GENERAL AND/OR LOCAL
EXHAUST) VENTILATION TO MAINTAIN EXPOSURE TO TLV(S).
Protective Gloves:NITRILE RUBBER.
Eye Protection:CHEM SPLASH GOGGLES (COMPLY W/OSHA REG)
Other Protective Equipment:WEAR IMPERVIOUS CLOTHING AND BOOTS.
Work Hygienic Practices:KEEP WORK AREA CLEAN & FREE FROM LEAKS/SPILLS.
ALWAYS WASH HANDS THOROUGHLY W/SOAP & WATER BEFORE HANDLING FOOD &
DRINK.
Supplemental Safety and Health

HCC:F4
Boiling Pt:B.P. Text:300 F
Vapor Density:> THAN AIR
Viscosity:67-77 KU
Evaporation Rate & Reference:70 (ETHER = 1)
Appearance and Odor:COLORED LIQUID WITH A MILD, SWEET, AROMATIC ODOR.
Percent Volatiles by Volume:50

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:KEEP AWAY FROM OPEN FLAMES, SPARKS, AND
HEAT. DO NOT WELD NEAR OR AROUND PRODUCT.

Waste Disposal Methods:DESTROY BY LIQUID INCINERATION. CONTAMINATED
ABSORBENT MAY BE DEPOSITED IN A LANDFILL IN ACCORDANCE WITH
LOCAL/STATE AND FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.