BNLMP - ETP CUTTING FLUID, 93215

  • MSDS: BNLMP
  • Manufacturer: PREMIER INDUSTRIAL CORP
  • Product Name: ETP CUTTING FLUID, 93215
  • National Stock Number: 9150-00N027138
Product Identification

Product ID:ETP CUTTING FLUID, 93215
MSDS Date:01/29/1990
FSC:9150
NIIN:00N027138
MSDS Number: BNLMP

Responsible Party
PREMIER INDUSTRIAL CORP
4500 EUCLID AVE
CLEVELAND, OH 44103
US

Emergency Phone: 216-391-8300

Info Phone: 216-391-8300

Preparer: C.M.B.

Cage: 18399

Contractor
PREMIER FARNELL CORPORATION
CLEVELAND, OH 44103-3736 US

Telephone: 216-391-8300

Cage: 18399

Ingredients

MINERAL OIL, PETROLEUM DISTILLATES, HYDROTREATED HEAVY

CAS: 64742-52-5

RTECS: PY8035000

Fraction By Weight: 30-60%

OSHA PEL 5 MG/M3 (OIL MIST)

ACGIH TLV: 5MG/M3;10STEL(MIST)


NON-HAZARDOUS INGREDIENT


CALCIUM PETROLEUM SULFONATE

CAS: 61789-86-4

RTECS: WR7140000

Fraction By Weight: >1%


LARD OIL

CAS: 8016-28-2

Fraction By Weight: >1%

Hazards

LD50 LC50 Mixture:LD50: (ORAL, RAT) 13000 MG/KG
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:PRODUCT IS NOT A PRIMARY SKIN OR EYE
IRRITANT, CHRONIC IRRITATION MAY OCCUR AFTER PROLONGED AND REPEATED
CONTACT WITH SKIN.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid

First Aid:EYES: IMMEDIATELY FLUSH WITH PLENTY OF WATER FOR AT LEAST 15
MINUTES. CALL MD. SKIN: WASH THORO WITH PLENTY OF WATER & SOAP.
INHAL: IF AFFECTED, REMOVE TO FRESH AIR. INGEST: SEEK MD
IMMEDIATELY, SHOW MSDS OR LABEL. DO NOT INDUCE VOMITING.

Fire Fighting

Flash Point:450F,232C
Extinguishing Media:CO2, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.

Accidental Release

Spill Release Procedures:CLEAN UP WITH ABSORBENT MATERIAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:AVOID PROLONGED OR REPEATED CONTACT
WITH SKIN. WASH THORO AFTER USING. ALWAYS READ AND FOLLOW
DIRECTIONS ON PRODUCT LABEL.
Other Precautions:IN CASE OF ACCIDENT OR ILLNESS, SEEK MD IMMED, SHOW
LABEL OR MSDS. KEEP OUT OF REACH OF CHILDREN. ADDITIONAL TECHNICAL
DATA SHEETS &/MSDS ARE AVAILABLE UPON REQUEST. FOR PROFESSIONAL AND
INDUSTRIAL US E ONLY.

Exposure Controls

Respiratory Protection:IF VENTILATION IS INADEQUATE, WEAR NIOSH/MSHA
APPROVED RESPIRATORY EQUIPMENT.
Ventilation:LOCAL: RECOMMENDED. MECH: REQUIRED.
Protective Gloves:SOLVENT RESISTANT GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

Chemical Properties

HCC:V6
Boiling Pt:B.P. Text:680F,360C
Vapor Pres:NIL
Spec Gravity:0.99
Evaporation Rate & Reference:<0.1 (WATER=1)
Solubility in Water:NIL
Appearance and Odor:TAN OPAQUE FLUID, WITH PETROLEUM ODOR.
Percent Volatiles by Volume:NIL

Stability

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS.
Stability Condition to Avoid:KEEP AWAY FROM HEAT AND FLAME.
Hazardous Decomposition Products:CO, PYROLYSIS PRODUCTS.

Disposal

Waste Disposal Methods:DISPOSE OF AS A NON-HAZARDOUS WASTE. CONTAIN AND
PICK-UP WASTE MATERIALS. DISPOSE OF I/A/W FEDERAL, STATE AND LOCAL
REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.