Product ID:TORRSEAL PART A
MSDS Date:05/20/1986
FSC:8030
NIIN:00-998-3321
Kit Part:Y
MSDS Number: BNWQQ

VARIAN ASSOCIATES

611 HANSEN WAY
PALO ALTO, CA 94303
US

Emergency Phone: 415-493-4000

Info Phone: 415-493-4000

Cage: 7S575

VARIAN ASSOCIATES

PALO ALTO, CA 94303 US

Telephone: 415-493-4000

Cage: 7S575

MAGNESIUM SILICATE HYDRATE

CAS: 1343-90-4

RTECS: OM4360000

Fraction By Weight: 46%

ACGIH TLV: 2 MG/M3

BIS PNENOL A-EPICHLORONYDRIN EPXY RESIN

Fraction By Weight: 50%

TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 2 - 10%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293

Routes of Entry: Inhalation:NO Skin:NO Ingestion:NO
Health Hazards Acute and Chronic:MAY BE MILDLY IRRITATING TO SKIN.
Effects of Overexposure:CONTACT WITH SKIN OR EYES MAY CAUSE IRRITATION.
Medical Cond Aggravated by Exposure:NONE KNOWN.

First Aid:IN CASE OF SKIN CONTACT WASH WITH SOAP AT FIRST OPPORTUNITY.
IN CASE OF EYE CONTACT FLUSH WITH COPIOUS AMOUNTS OF WATER FOR 15
MINUTES.

Flash Point Method:COC
Flash Point:470F,243C
Extinguishing Media:CO2, FOAM, OR DRY CHEMICAL.
Fire Fighting Procedures:NONE.
Unusual Fire/Explosion Hazard:NONE.

Spill Release Procedures:SCRAPE UP, TRANSFER TO METAL CONTAINER.
SOLVENTS MAY BE NECESSARY TO CLEAN UP STICKY RESIDUE, BUT OBSERVE
HEALTH AND FIRE HAZARDS OF SOLVENT.

Handling and Storage Precautions:STORE AWAY FROM DIRECT HEAT, WHICH
MIGHT CAUSE PHYSICAL SEPARATION OF FILLER.

Respiratory Protection:NONE REQUIRED.
Ventilation:LOCAL EXHAUST: ONLY IF HEATED.
Protective Gloves:RUBBER OR PLASTIC.
Eye Protection:GOGGLES WHERE THERE IS DANGER OF SPLASH.
Other Protective Equipment:NONE REQUIRED.
Supplemental Safety and Health

Melt/Freeze Pt:M.P/F.P Text:0F,-18C
Vapor Pres:NIL
Spec Gravity:1.6 (WATER=1)
Evaporation Rate & Reference:>1 (BU AC=1)
Solubility in Water:INSOLUBLE
Appearance and Odor:WHITE HIGH VISCOUS LIQUID, VERY SLIGHT ODOR.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Hazardous Decomposition Products:CARBON MONOXIDE, ALDEHYDES.
Conditions to Avoid Polymerization:DO NOT MIX LARGE AMOUNTS OF EPOXY
RESIN WITH DIETHYLENETRIAMINE WITHOUT RECOGNITION OF DEVELOPMENT OF
EXOTHERMIC HEAT.

Waste Disposal Methods:THIS IS NOT A HAZARDOUS MATERIAL UNDER THE
RESOURCE CONSERVATION AND RECOVERY ACT (RCRA).

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.