Product ID:SATINHIDE 20-544 LO-LUSTRE NEUTRAL BASE ALK
MSDS Date:09/13/1991
FSC:8010
NIIN:00N034176
MSDS Number: BPXJR

PPG INDUSTRIES INC

4325 ROSANNA DR
ALLISON PARK, PA 15101
US

Emergency Phone: 412-492-5554

Info Phone: 412-492-5554

Cage: 47695

PPG INDUSTRIES INC

PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

ALUMINUM SILICATE

CAS: 1335-30-4

Fraction By Weight: 15-20%

CALCIUM CARBONATE

CAS: 471-34-1

RTECS: FF9335000

Fraction By Weight: 15-20%

OSHA PEL 10 MG/M3

ACGIH TLV: 10 MG/M3

HYDROTREATED HEAVY NAPHTHA; (HYDROTREATED HEAVY NAPHTHA)

CAS: 64742-48-9

Fraction By Weight: 35-40%

ADDITIVES AND OTHER INGREDIENTS (INCLUDING FILM FORMERS AND

Fraction By Weight: 25-30%

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE:INGEST:HARMFUL OR FATAL IS
SWALLOWED. EYE:CAUSES IRRITATION. SKIN:MAY CAUSE MODERATE
IRRITATION. INHAL:VAPOR AND SPRAY MIST MAY BE HARMFUL IF INHALED.
CHRONIC:AVOID LONG TERM AND REPEATED CONTAC T.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:REDNESS, ITCHING, BURNING SENSATION AND VISUAL
DISTURBANCES MAY INDICATE EXCESSIVE EYE CONTACT. DRYNESS, ITCHING,
CRACKING, BURNING, REDNESS AND SWELLING ARE CONDITIONS ASSOCIATED
WITH EXCESSIVE SKIN CONTACT.

First Aid:INGEST:DO NOT INDUCE VOMIT. EYE:FLUSH IMMED W/PLENTY OF WATER
FOR AT LEAST 15 MIN. SKIN:REMOVE PROMPTLY BY WIPING, FOLLOWED BY
WATERLESS HAND CLEANER & SOAP & WATER. INHAL:REMOVE TO FRESH AIR.
APPLY A RTIF RESP & OTHER SUPPORTIVE MEASURES AS REQ. OTHER:IF
INGESTED, ANY TYPE OF OVEREXPOS/SYMPS OF OVEREXP OCCUR
DURING/FOLLOWING USE OF PROD, CONT POIS CNTRL CTR, EMERG ROOM/MD
IMMED; HAVE MSDS AVAIL.

Flash Point Method:PMCC
Flash Point:120F,49C
Lower Limits:0.7%
Extinguishing Media:USE NFPA CLASS B EXTING (CO*2, DRY CHEM/UNIVERSAL
AQUEOUS FILM FORMING FOAM) DESIGNED TO EXTING NFPA CLASS (SUPDAT)
Fire Fighting Procedures:USE NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP .
WATER SPRAY MAY BE INEFT. WATER SPRAY MAY BE USED TO COOL CLSD
CONTRS TO PREVENT PRESS BUILD-UP & (SUPDAT)
Unusual Fire/Explosion Hazard:KEEP CONTRS TIGHTLY CLSD. ISOLATE FROM
HEAT, ELEC EQUIP, SPARKS & OPEN FLAMES. CLSD CONTRS MAY EXPLODE
WHEN EXPOSED TO EXTREME HEAT. DO NOT APPLY ON (SUPDAT)

Spill Release Procedures:PROVIDE MAX VENT. ONLY PERSONNEL EQUIPPED
W/PROPER RESP & SKIN & EYE PROT SHOULD BE PERMITTED IN AREA. REMOVE
ALL SOURCES OF IGNITION. TAKE UP SPILLED MATL W/SAWDUST,
VERMICULITE/OTHER ABSORB MATL & P LACE INTO CONTR FOR DISP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LARGE
QUANTITIES IN BUILDING DESIGNED AND PROTECTED FOR STORAGE OF NFPA
CLASS II COMBUSTIBLE LIQUIDS.
Other Precautions:CONTAINERS SHOULD BE GROUNDED WHEN POURING. AVOID
FREE FALL OF LIQUID IN EXCESS OF A FEW INCHES.

Respiratory Protection:WHERE VENTILATION IS INADEQUATE, USE A SUITABLE
NIOSH/MSHA APPROVED RESPIRATOR.
Ventilation:USE ADEQUATE VENTILATION.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEM WORK GOGG/FULL LENGTH FCSHLD.
Other Protective Equipment:IMPERMEABLE APRON.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
DECOMP PROD:CARBON MONOXIDE FUMES. EXTING MEDIA:II COMBUST LIQ FIRES.
FIRE FIGHT PROC:POSS AUTOIGNIT/EXPLOS WHEN EXPOSED TO EXTREME HEAT.
IF WATER IS USED, FOG NOZZ ARE PREF. EXPLOS HAZ:HOT SURF. TOXI C
GASES MAY FORM WHEN PROD IS CONTACTEDBY FLAME/HOT SURF.

HCC:F4
Boiling Pt:B.P. Text:>212F,>100C
Vapor Pres:0.5
Vapor Density:HVR/AIR
Spec Gravity:1.11
Evaporation Rate & Reference:12 (BUTYL ACETATE = 100)
Solubility in Water:0.0%
Appearance and Odor:VISCIOUS LIQUID WITH AN ODOR CHARACTERISTIC OF
SOLVENTS LISTED.
Percent Volatiles by Volume:54.70

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRODUCE HAZ DECOMP PRODS WHEN
HEATED. WELDING/BRAZING/FLAME-CUTTING ON SURF COATED W/PROD MAY
PROD (SUPDAT)

Waste Disposal Methods:WASTE MATL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE, PROVINCIAL AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINER SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WASTE MA NAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.