BPXQJ - SUNPROOF ONE-COAT WHITE, SASH & TRIM, 1-45

  • MSDS: BPXQJ
  • Manufacturer: PPG INDUSTRIES INC
  • Product Name: SUNPROOF ONE-COAT WHITE, SASH & TRIM, 1-45
  • National Stock Number: 8010-00N034400
Product Identification

Product ID:SUNPROOF ONE-COAT WHITE, SASH & TRIM, 1-45
MSDS Date:06/16/1992
FSC:8010
NIIN:00N034400
MSDS Number: BPXQJ

Responsible Party
PPG INDUSTRIES INC
4325 ROSANNA DRIVE
ALLISON PARK, PA 15101
US

Emergency Phone: 412-492-5555;304-843-1300

Info Phone: 216-572-6111;800-441-9695

Cage: 47695

Contractor
PPG INDUSTRIES INC
PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

Ingredients

VERY LIMITED. SINCE OVEREXPOSURES ARE NOT EXPECTED,

RTECS: 9999999ZZ


TYPE OF AIRBORNE CONTAMINANTS AGAINST WHICH

RTECS: 9999999ZZ


LIMITS,LEL IN FIRE AND EXPLO HAZ BELOW STATED LIMIT, &

RTECS: 9999999ZZ


ON SURFACES COATED WITH THIS PRODUCT.

RTECS: 9999999ZZ


PHTHALIMIDE PHTHALIMIDE, N-((TRICHLOROMETHYL) THIO)-;

CAS: 133-07-3

RTECS: TI5685000

Fraction By Weight: 1-2%


ALUMINUM SILICATE

CAS: 1335-30-4

Fraction By Weight: 2-5%


1); (CALCIUM CARBONATE)

CAS: 471-34-1

RTECS: FF9335000

Fraction By Weight: 10-15%

OSHA PEL 10 MG/M3

ACGIH TLV: 10 MG/M3


TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 20-25%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293


SOLVENT NAPHTHA (PETROLEUM), MEDIUM ALIPHATIC

CAS: 64742-88-7

Fraction By Weight: 20-25%


FILM FORMERS, RESINS, AND ADDITIVES

Fraction By Weight: 30-35%


AVOID LONG TERM & RPTD CONT. PROD

RTECS: 9999999ZZ


TITANIUM DIOXIDE DUST IN LONG-TERM STUDY DEVELOPED

RTECS: 9999999ZZ


INDICATE NO INCR RISK OF CANCER FROM EXPOS.POTNTL FOR

RTECS: 9999999ZZ

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE:INGEST: HARMFUL/FATAL IF
SWALLOWED. EYE:CAUSES IRRIT. SKIN:MAY CAUSE MOD IRRIT.INHAL:VAP &
SPRAY MIST MAY BE HARMFUL.VAP IRRIT EYES, NOSE,& THROAT.RPTD EXPOS
TO HIGH VAP CONC MAY CAUSE IRRIT OF RESP SYS & PERM BRAIN & NERV
SYS DMG. INTENTIONAL MISUSE BY DELIB CONC & INHALING CONTENTS CAN
BE HARMFUL/FATAL. (ING 7)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:EYE WATERING, HEADACHES, NAUSEA, DIZZINESS, AND
LOSS OF COORDINATION ARE INDICATIONS THAT SOLVENT LEVS ARE TOO
HIGH. REDNESS, ITCHING, BURNING SENSATION AND VISUAL DISTURBANCES
MAY INDICATE EXCESSIVE EYE CONT. DRYNESS, ITCHING, CRACKING,
BURNING, REDNESS, AND SWELLING ARE CONDITIONS ASSOCIATED WITH
EXCESSIVE SKIN CONT.
Medical Cond Aggravated by Exposure:NOT APPLICABLE.

First Aid

First Aid:INGEST:DO NOT INDUCE VOMIT. EYE:FLUSH EYES IMMED W/PLENTY OF
H*2O FOR AT LST 15 MIN. SKIN: FLUSH IMMED W/PLENTY OF H*2O,
FOLLOWED BY WATERLESS HAND CLEANER & SOAP & H*2O IF MATL APPEARS TO
ADHERE TO S KIN. INHAL: REMOVE TO FRESH AIR. APPLY ARTF RESP &
OTHER SUPPORTIVE MEASURES AS REQD. OTHER: IF INGEST, ANY TYPE OF
OVEREXP/SYMP OF OVEREXP OCCUR DURING/FOLLOWING USE OF PROD, CONT
POIS CNTRL (SUPDAT)

Fire Fighting

Flash Point Method:PMCC
Flash Point:115F,46C
Lower Limits:1%
Extinguishing Media:USE NFPA CLASS B EXTING (CARBON DIOXIDE, DRY
CHEM/UNIVERSAL AQUEOUS FILM FORMING FOAM) DESIGNED TO EXTING NFPA
(SUPDAT)
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT
EQUIP.H*2O SPRAY MAY BE INEFT.H*2O SPRAY MAY BE USED TO COOL CLSD
CNTNRS TO PVNT PRESS BUILD-UP & POSS (SUPDAT)
Unusual Fire/Explosion Hazard:KEEP CNTNRS TIGHTLY CLSD.ISOLATE FROM
HEAT,ELEC EQUIP,SPARKS,& OPEN FLAMES.CLSD CNTNRS MAY EXPLO WHEN
EXPOS TO EXTREME HEAT.DO NOT APPLY ON HOT SURFS. (SUPDAT)

Accidental Release

Spill Release Procedures:PROVIDE MAXIMUM VENT. ONLY PERSONNEL EQUIPPED
W/RESP & SKIN & EYE PROT SHOULD BE PERMITTED IN AREA. REMOVE ALL
SOURCES OF IGNIT. TAKE UP SPILLED MATL W/SAWDUST, VERMICULITE, OR
OTHER ABSORB MATL AND P LACE INTO CONTAINERS FOR DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LARGE
QUANTITIES IN BUILDINGS DESIGNED AND PROTECTED FOR STORAGE OF NFPA
CLASS II COMBUSTIBLE LIQUIDS.
Other Precautions:IF MATL IS PART OF MULTIPLE COATING SYS, READ MSDS
FOR OTHER COMPONENT/COMPONENTS BEFORE BLENDING AS RSLTG MIX MAY
HAVE HAZ OF ALL OF ITS PARTS. CNTNRS SHOULD BE GROUNDED WHEN
POURING. AVOID FREE FALL OF LIQ IN EXCESS OF FEW INCHES.

Exposure Controls

Respiratory Protection:OVEREXP TO VAPS MAY BE PVNTD BY ENSURING VENT
CNTRLS,VAP EXHST/FRESH AIR ENTRY.NIOSH/MSHA APPRVD (TC-23C-) AIR
PURIFYING/AIR SUPPLIED (TC-19C-) RESP MAY ALSO REDUCE EXPOS. READ
RESP MFR INSTRUCTIONS & LITERATURE CAREFULLY TO DETERM (ING 11)
Ventilation:PROVIDE GEN DILUTION/LOC EXHST VENT IN VOL & PATTERN TO
KEEP CONC OF INGS LISTED BELOW LOWEST SUGGESTED EXPOS (ING 12)
Protective Gloves:NITRILE RUB OR NEOPRENE RUB GLOVES.
Eye Protection:CHEM WORK GOG/FULL LGTH FACESHLD .
Other Protective Equipment:WEAR PROTECTIVE CLOTHING, INCLUDING
IMPERMEABLE APRON CONSTRUCTED OF NITRILE RUBBER OR NEOPRENE RUBBER.
Work Hygienic Practices:CLEAN OR DISCARD CONTAMINATED CLOTHING AND
SHOES.
Supplemental Safety and Health
EXTING MEDIA: CLASS II COMBUST LIQ FIRES. FIRE FIGHT PROC:
AUTOIGNIT/EXPLO WHEN EXPOS TO EXTREME HEAT. IF H*2O USED, FOG NOZ
PREF. EXPLO HAZ: TOX GASES MAY FORM WHEN PROD IS CONTACTED BY
FLAME/HOT SUR FS. HAZ DECOMP PRODS: INCL: CARBON MONOXIDE. FIRST
AID PROC: CENTER, EMERGENCY ROOM OR PHYS IMMED; HAVE MSDS INFO
AVAIL.

Chemical Properties

HCC:F4
Boiling Pt:B.P. Text:>280F,>138C
Vapor Pres:2.1
Vapor Density:HVR/AIR
Spec Gravity:1.31
Evaporation Rate & Reference:18 (BUTYL ACETATE=100)
Solubility in Water:0.2%
Appearance and Odor:VISCOUS LIQUID WITH AN ODOR CHARACTERISTIC OF
SOLVENTS LISTED IN ING SECTION
Percent Volatiles by Volume:41.2

Stability

Stability Indicator/Materials to Avoid:YES
CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS, OR STRONG OXIDIZING
AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRDCE HAZ DECOMP PRODS WHEN
HEATED.WELDING BRAZING/FLAME-CUTTING ON SURFS COATED W/PROD MAY
PRDCE FUMES (SUPDAT)

Disposal

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE, PROVINCIAL, AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WA STE MANAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.