BSDCM - FX-1 CARTRIDGE BLACK, H11-6221-410
- MSDS: BSDCM
- Manufacturer: CANON USA INC
- Product Name: FX-1 CARTRIDGE BLACK, H11-6221-410
- National Stock Number: 6850-01-365-9568
Product Identification
Product ID:FX-1 CARTRIDGE BLACK, H11-6221-410
MSDS Date:03/01/1994
FSC:6850
NIIN:01-365-9568
MSDS Number: BSDCM
Responsible Party
LAKE SUCCESS, NY 11042
US
Emergency Phone: 800-424-9300 (CHEMTREC)
Info Phone: 516-328-5600
Preparer: JOSEPH PALMERI
Cage: 1BA63
Contractor
Telephone: 516-328-5600
Cage: 1BA63
Ingredients
STYRENE ACRYLATE COPOLYMER
CAS: 25153-46-2
Fraction By Weight: 55-65%
OSHA PEL N/K
ACGIH TLV: N/K
IRON OXIDE
CAS: 1317-61-9
Fraction By Weight: 30-40%
OSHA PEL 10 MG/M3
ACGIH TLV: 5 MG/M3
Hazards
LD50 LC50 Mixture:LD50: (ORAL, RATS) >5000 MG/KG
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHAL: EXPECTED TO BE LOW HAZ FOR
RECOM HNDLG. EYES: NO SPECIFIC HAZS KNOWN. MAY CAUSE TRANSIENT
IRRIT. NOT CLASSIFIED AS IRRIT, ACCDG TO OSHA HAZ-COMM. SKIN:
EXPECTED TO BE LOW HAZ FOR RECOM HNDLG. N OT CLASSIFIED AS IRRIT,
ACCDG TO OSHA HAZ-COMM STD. INGEST: EXPECTED TO BE LOW HAZ.
CHRONIC: BASED ON (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: AVAIL DATA, HUMAN EXPOS TO TONER HAS
BEEN SHOWN TO CAUSE MINIMAL RESP TRACT IRRIT AS MAY OCCUR W/LG AMTS
OF ANY NONTOX DUSTS. RSLTS OF ONE ANIMAL STUDY WHERE RATS INHALED
TONER THAT WAS 10 T IMES MORE RESPIRABLE THAN COMMERCIALLY AVAIL
TONER WERE OBSERVED TO HAVE NO LUNG CHANGES AT LOW EXPOS (MOST
(SUPDAT)
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:INHAL: IF SYMPTOMATIC, MOVE TO FRESH AIR. GET MEDICAL
ATTENTION IF SYMPTOMS PERSIST. EYES: ANY MATERIAL THAT CONTACTS THE
EYE SHOULD BE WASHED OUT IMMEDIATELY WITH WATER FOR AT LEAST 15
MINUTES. GET M EDICAL ATTENTION IF SYMPTOMS OCCUR. SKIN: WASH WITH
SOAP & WATER. GET MEDICAL ATTENTION IF SYMPTOMS OCCUR. INGEST:
DRINK 1-2 GLASSES OF WATER. SEEK MEDICAL ATTENTION.
Fire Fighting
Extinguishing Media:WATER SPRAY, CARBON DIOXIDE (CO*2), DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:TONER MATERIAL, LIKE MOST ORGANIC
MATERIAL IN POWDER FORM, IS CAPABLE OF CREATING A DUST EXPLOSION.
Accidental Release
Spill Release Procedures:NO TONER SPILLAGE OCCURS IN NORM
OPERATION/HNDLG. IF IT SHOULD OCCUR, AVOID INHAL OF DUST. SWEEP
MATL ONTO PAPER & DISP OF COLLECTED TONER AS PLASTIC WASTE. MATL
HAS NOT BEEN TESTED FOR ENVIRON EFTS. IN SPILL SITUATION IT MAY BE
VISUALLY (SUPDAT)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:AVOID BREATHING DUST. USE WITH
ADEQUATE VENTILATION. WASH THOROUGHLY AFTER HANDLING.
Other Precautions:KEEP FROM CONTACT W/OXIDIZING MATLS. MINIMIZE DUST
GENERATION & ACCUMULATION. REFER TO PAMPHLET NO. 654, "PREVENTION
OF FIRE & DUST EXPLOSION IN CHEMICAL, DYE, PHARMACEUTICAL &
PLASTICS INDUSTRIES." U SE ADEQUATE VENT. STORE IN A COOL PLACE.
Exposure Controls
Respiratory Protection:NONE SHOULD BE NEEDED. USE NIOSH/MSHA APPROVED
RESPIRATOR APPROPRIATE FOR EXPOSURE OF CONCERN .
Ventilation:GOOD VENT (TYPICALLY 4-6 ROOM VOLUMES PER HOUR) SHOULD BE
USED. VENTILATION RATES SHOULD BE MATCHED TO CONDITIONS.
Protective Gloves:IMPERVIOUS GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:WASHING FACILITIES.
Work Hygienic Practices:GOOD INDUSTRIAL HYGIENE PRACTICE SHOULD BE
FOLLOWED WHICH INCLUDES PREVENTING EYE CNTCT, MINIMIZING SKIN CNTCT
& INHAL.
Supplemental Safety and Health
EFTS OF OVEREXP: RELEVANT LEVEL TO POTNTL HUMAN EXPOS). AT HIGH LEVELS
A SLIGHT DEGREE OF LUNG FIBROSIS OBSERVED DUE TO EXCESS AMTS OF
DUST RETAINED IN LUNGS FOR PROLONGED INTERVAL. SPILL PROC: UNPLEA
SANT; HOWEVER, IT IS NOT EXPECTED TO CAUSE ANY ADVERSE ENVIRON
EFTS.
Chemical Properties
HCC:N1
Melt/Freeze Pt:M.P/F.P Text:>212F,>100C
Spec Gravity:1.4-1.6(H*2O=1)
Solubility in Water:NEGLIGIBLE
Appearance and Odor:FINE BLACK POWDER; TYPICAL PLASTIC ODOR.
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:COMBUSTION WILL PRODUCE CARBON DIOXIDE
AND CARBON MONOXIDE.
Disposal
Waste Disposal Methods:INCINERATE OR LANDFILL. CAN BE INCINERATED WHEN
IN COMPLIANCE WITH LOCAL REGULATIONS. DISCHARGE, TREATMENT OR
DISPOSAL MAY BE SUJBECT TO FEDERAL, STATE OR LOCAL LAWS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.