BSXQJ - WALLHIDE BONE WHITE FLAT LATEX, 80-125

  • MSDS: BSXQJ
  • Manufacturer: PPG INDUSTRIES INC
  • Product Name: WALLHIDE BONE WHITE FLAT LATEX, 80-125
  • National Stock Number: 8010-00N042333
Product Identification

Product ID:WALLHIDE BONE WHITE FLAT LATEX, 80-125
MSDS Date:12/22/1992
FSC:8010
NIIN:00N042333
MSDS Number: BSXQJ

Responsible Party
PPG INDUSTRIES INC
4325 ROSANNA DR
ALLISON PARK, PA 15101
US

Emergency Phone: 304-843-1300; 800-441-9695

Info Phone: 216-572-6111; 412-492-5555

Cage: 47695

Contractor
PPG INDUSTRIES INC
PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

Ingredients

TITANIUM OXIDE; (TITANIUM DIOXIDE)

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 15-20%

OSHA PEL 10 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST


ETHYLENE GLYCOL (SARA III)

CAS: 107-21-1

RTECS: KW2975000

Fraction By Weight: 2-5%

OSHA PEL 50 PPM, C

ACGIH TLV: 50 PPM, VAP/MIST, C

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB


WATER; (DEIONIZED WATER)

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 45-50%


PROPIONIC ACID, 2-METHYL-, MONOESTER WITH

CAS: 25265-77-4

RTECS: UF6000000

Fraction By Weight: 1-2%


FILM FORMERS, RESINS, & ADDITIVES

Fraction By Weight: 10-15%


SILICA, CRYSTALLINE - CRISTOBALITE

CAS: 14464-46-1

RTECS: VV7325000

Fraction By Weight: 1-2%

OSHA PEL 0.05 MG/M3 RDUST

ACGIH TLV: 0.05 MG/M3 RDUST


THESE EFTS FOUND IN HUMANS. REDNESS, ITCHING,

RTECS: 9999999ZZ


EYE CNTCT. DRYNESS, ITCHING, CRACKING, BURNING,

RTECS: 9999999ZZ


ROOM/MD IMMED; HAVE MSDS INFORMATION AVAIL.

RTECS: 9999999ZZ


THE LEL BELOW STATED LIMIT & TO REMOVE DECOMP PRODUCTS


CLAY (KAOLIN); (ALUMINUM SILICATE)

CAS: 1332-58-7

RTECS: GF1670500

Fraction By Weight: 2-5%

OSHA PEL 10MG/M3 TDUST; 5RESP

ACGIH TLV: 2 MG/M3 TDUST


SILICA, CRYSTALLINE - FUSED; (SILICA, AMORPHOUS-FUSED)

CAS: 60676-86-0

RTECS: VV7328000

Fraction By Weight: 2-5%

OSHA PEL 0.1 MG/M3 RDUST

ACGIH TLV: 0.1 MG/M3 RDUST


SILICA, CRYSTALLINE - QUARTZ; (MICROCRYSTALLINE SILICA

CAS: 14808-60-7

RTECS: VV7330000

Fraction By Weight: 5-10%

OSHA PEL 0.1 MG/M3 RDUST

ACGIH TLV: 0.1 MG/M3 RDUST

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:INGEST:HARMFUL/FATAL IF SWALLOWED.
EYES: CAUSES IRRIT. SKIN:MAY CAUSE SLIGHT IRRIT. INHAL:VAP & SPRAY
MIST MAY BE HARMFUL IF INHALED. SANDING & GRINDING DUSTS MAY BE
HARMFUL. VAP GENERATED @ ELEVATED TEMP IRRIT EYES, NOSE & THROAT.
CHRONIC:AVOID LONG TERM & RPTD CNTCT. PROD CONTAINS FORM OF
CRYSTALLINE (EFTS OF OVEREXP
Explanation of Carcinogenicity:CRYSTALLINE SILICA (QUARTZ &
CRISTOBALITE: (IARC 2A; IARC VOL 7, PG 341, 1987. NTP 6TH ANN RPT
ON CARCIN, (SUPDAT)
Effects of Overexposure:HLTH HAZ:SILICA/QUARTZ WHICH IARC ASSOC W/
INCREASED RISK OF CANCER IN LAB ANIMALS. LONG-TERM EXPOS MAY ALSO
LEAD TO DISABLING INJURY KNOWN AS SILICOSIS. THESE EFTS ASSOC
W/BRTHG EXCESSIVE AMTS OF SIL ICA DUST. APPLICATN OF PROD NOT
EXPECTED TO GENERATE EXCESSIVE AMTS OF RESPIRABLE SILICA/QUARTZ, SO
POTNTL HAZ (SUPDAT)
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid

First Aid:INGEST:IF SWALLOWED, DO NOT INDUCE VOMIT. EYES:FLUSH EYES
IMMED W/PLENTY OF WATER FOR @ LEAST 15 MIN. SKIN:FLUSH IMMED
W/PLENTY OF WATER FOLLOWED BY WASHING W/SOAP & WATER. INHAL:IF
AFFECTED BY INHAL OF VAP/SPRAY MIST, REMOVE TO FRESH AIR.APPLY
ARTF RESP & OTHER SUPPORTIVE MEASURES AS REQD. IF INGEST/ANY TYPE
OF OVEREXP/SYMP OCCUR DURING/FOLLOWING USE OF PROD, CNTCT POIS CTL
CTR, EMER (ING 12)

Fire Fighting

Flash Point Method:PMCC
Flash Point:0F,-18C
Extinguishing Media:NFPA CLASS B EXTING (CO2, DRY CHEM/UNIVERSAL AQ
FILM FORMING FOAM) DESIGNED TO EXTING NFPA CLASS IIIB COMBUST LIQ
FIRE.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
. WATER SPRAY MAY BE INEFTIVE. MAY BE USED TO COOL CLSD CONTRS TO
PVNT PRESS BUILD-UP & POSS (SUPDAT)
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE OR BURST
(DUE TO BUILD-UP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME HEAT.

Accidental Release

Spill Release Procedures:PROVIDE MAX VENT. ONLY PERS EQUIPPED W/ PROPER
RESP & SKIN & EYE PROTECTION SHLD BE PERMITTED IN AREA. REMOVE ALL
SOURCES OF IGNIT. TAKE UP SPILLED MATL W/SAWDUST, VERMICULITE/OTHER
ABSORBENT MATL & P LACE INTO CNTRS FOR DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:DO NOT STORE ABOVE 120 F. STORE LGE
QTYS IN BUILDINGS DESIGNED & PROTECTED FOR STOR OF NFPA CLASS IIIB
COMBUST LIQUIDS. PROTECT FROM FREEZING.
Other Precautions:IF MATL IS PART OF MULTIPLE COMPONENT SYSTEM, READ
MSDS FOR OTHER COMPONENT/COMPONENTS BEFORE BLENDING AS RESULTING
MIX MAY HAVE HAZARDS OF ALL OF ITS PARTS.

Exposure Controls

Respiratory Protection:WHERE VENTIALTION IS INADEQUATE, USE A
NIOSH/MSHA APPROVED RESPIRATOR.
Ventilation:PROVIDE GEN DILUTION/LOC EXHAUST VENT IN VOL & PATTERN TO
KEEP CONC OF INGRED BELOW LOWEST SUGGESTED EXPOS LIM, (ING 13)
Protective Gloves:GLOVES OF NITRILE, NEOPRENE/LATEX.
Eye Protection:ANSI APRV CHEMICAL WORKERS GOGGLES (FP N
Other Protective Equipment:PROTECTIVE CLTHG, INCLUDING IMPERMEABLE
APRON.
Work Hygienic Practices:CLEAN OR DISCARD CONTAMINATED CLOTHING & SHOES.
Supplemental Safety and Health
FIRE FIGHT PROC:AUTOIGNIT/EXPLOSION WHEN EXPOS TO EXTREME HEAT. IF
WATER USED, FOG NOZZLES PREF. EXPLAN OF CARCIN: 1991; ANTIC TO BE
CARCIN. EFTS OF OVEREXP:FOR HUMANS IS LIMITED. PROD CONTAINS ETHYLE
NE GLYCOL WHICH MAY CAUSE KIDNEY & LIVER DMG & HAS BEEN SHOWN TO
CAUSE BIRTH DEFECTS IN LAB ANIMALS. NO EVID OF (ING 10

Chemical Properties

HCC:F2
Boiling Pt:B.P. Text:>212F,>100C
Vapor Pres:17.1
Vapor Density:HVR/AIR
Spec Gravity:1.31
Evaporation Rate & Reference:32 (BUOAC=100)
Solubility in Water:51.3%
Appearance and Odor:VISCOUS LIQ W/ODOR CHARACT OF CHEM FAMILY & ANY
SOLVENTS LISTED IN INGREDIENTS.
Percent Volatiles by Volume:68.90

Stability

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT W/STRONG ALKALIES, STRONG MINERAL ACIDS OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRDCE HAZ DECOMP PROD WHEN HEATED.
WELDING, BRAZING OR FLAME-CUTTING MAY PROD FUMES INCLUDING CO,
FORMALDEHYDE.

Disposal

Waste Disposal Methods:WASTE MATL MUST BE DISPOSED OF IN ACCORDANCE W/
FEDERAL, STATE, PROVINCIAL & LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WASTE MANAG EMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.