BVVWB - WALL TILE GROUT EM, 22328
- MSDS: BVVWB
- Manufacturer: DAP INC
- Product Name: WALL TILE GROUT EM, 22328
- National Stock Number: 8030-00N053847
Product Identification
Product ID:WALL TILE GROUT EM, 22328
MSDS Date:09/22/1986
FSC:8030
NIIN:00N053847
MSDS Number: BVVWB
Responsible Party
US
Emergency Phone: 800-543-3840
Info Phone: 800-543-3840
Cage: 90300
Contractor
Telephone: 513-253-7154/800-543-3840
Cage: 90300
Ingredients
SILICATE, PORTLAND CEMENT; (PORTLAND CEMENT)
CAS: 65997-15-1
RTECS: VV8770000
Fraction By Weight: 55%
OSHA PEL 50 MPPCF
ACGIH TLV: 10 MG/M3 TDUST
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES:EXPOSURE TO DUST MAY RESULT IN
BUILD-UP OF MATERIAL IN EYES. SKIN:WET CEMENT CAN DRY SKIN & CAUSE
ALKALI BURNS. INGEST:NO INFORMATION GIVEN BY MANUFACTURER.
INHAL:EXPOSURE TO DUST MAY RESULT IN B UILD-UP IN EARS, NOSE &
MOUTH WHICH MAYCAUSE IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:EYE:FLUSH W/WATER FOR AT LEAST 15 MINUTES. CONTACT MD
IMMEDIATELY. SKIN:WASH W/SOAP & WATER. INGEST:DO NOT INDUCE
VOMITING. CONTACT MD OR REGIONAL POISON CONTROL CENTER.
INHAL:REMOVE TO FRESH AIR. CON TACT MD IMMEDIATELY.
Fire Fighting
Flash Point:NONE
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT . USE WATER SPRAY TO COOL EXPOSED SURFACES.
Unusual Fire/Explosion Hazard:NONE KNOWN.
Accidental Release
Spill Release Procedures:USE ABSORBENT MATERIAL OR SCRAPE UP DRIED
MATERIAL & PLACE INTO CONTAINERS.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:KEEP CONTAINERS TIGHTLY CLOSED WHEN
NOT IN USE. KEEP OUT OF REACH OF CHILDREN. KEEP CONTAINER FROM
EXCESSIVE HEAT.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.
Exposure Controls
Respiratory Protection:IF 8-HOUR EXPOSURE LIMIT OR VALUE IS EXCEEDED
FOR ANY COMPONENT, USE A NIOSH/MSHA APPROVED RESPIRATOR. CONSULT
YOUR SAFETY EQUIPMENT SUPPLIER & OSHA REGULATIONS, 29 CFR 1910.134
FOR RESPIRATOR REQUIRE MENTS.
Ventilation:IF DRY-SANDING, PROVIDE SUFFICIENT MECHANICAL VENTILATION &
MAINTAIN EXPOSURE BELOW PEL & TLV.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:NO INFORMATION GIVEN BY MANUFACTURER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.
Chemical Properties
HCC:N1
Spec Gravity:2.3-2.4
Solubility in Water:FORMS ALKALINE DISP
Appearance and Odor:FREE FLOWING POWDER; LOW ODOR W/SPECIFIED COLOR.
Percent Volatiles by Volume:<1
Stability
Stability Indicator/Materials to Avoid:YES
ACIDS.
Stability Condition to Avoid:EXCESSIVE HEAT.
Hazardous Decomposition Products:NONE KNOWN.
Disposal
Waste Disposal Methods:DISPOSAL MUST BE I/A/W FEDERAL, STATE & LOCAL
REGULATIONS. DO NOT REUSE CONTAINERS. THIS PRODUCT IS NON-HAZARDOUS
ACCORDING TO EPA'S HAZARDOUS WASTE MANAGEMENT REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.