Product ID:SATINHIDE LATEX NEUTRAL BASE, 30-587
MSDS Date:04/22/1994
FSC:8010
NIIN:00N068151
MSDS Number: CBHDN

PPG INDUSTRIES INC

4325 ROSANNA DR
ALLISON PARK, PA 15101
US

Emergency Phone: 412-492-5555; 304-843-1300

Info Phone: 800-441-9695

Cage: DO542

PPG INDUSTRIES INC. COATINGS & RESINS GP

9 ALLISON PARK, PA 15101

Telephone: 412-492-5555

Cage: DO542

CLAY (KAOLIN); (CLAY)

CAS: 1332-58-7

RTECS: GF1670500

Fraction By Weight: 5-10%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 2 MG/M3 TDUST

WATER; (TAP WATER)

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 20-25%

OSHA PEL N/K

ACGIH TLV: N/K

WATER; (DEIONIZED WATER)

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 35-40%

OSHA PEL N/K

ACGIH TLV: N/K

ETHANOL, 2-(2-BUTOXYETHOXY)-; (DIETHYLENE GLYCOL MONOBUTYL

CAS: 112-34-5

RTECS: KJ9100000

Fraction By Weight: 1-2%

OSHA PEL N/K

ACGIH TLV: N/K

FILM FORMERS, RESINS, & ADDITIVES

Fraction By Weight: 25-30%

OSHA PEL N/K

ACGIH TLV: N/K

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INGEST:HARMFUL/FATAL IF SWALLOWED.
EYES:CAUSES IRRIT. REDNESS, ITCHING, BURNING SENSATION & VISUAL
DISTURBS MAY INDICATE EXCESS EYE CNTCT. SKIN:MAY CAUSE SLIGHT
IRRIT. MAY BE ABSORBED THRU SKIN. DRYNE SS, ITCH, CRACKING,
BURNING, REDNESS & SWELL ARE CNDTNS ASSOC W/EXCESS SKIN CNTCT.
INHAL:VAP & SPRAY (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: MIST MAY BE HARMFUL IF INHALED. VAPS
GENERATED AT ELEVATED TEMPS IRRIT EYES, NOSE & THROAT. CHRONIC:
AVOID LONG TERM & RPTD CNTCT. PROD CNTNS DIETHYLENE GLYCOL
MONOBUTYL ETHER (DEGME). DEGME CONSUMED IN DRINKING WATER AT LOW
LEVELS BY RATS FOR 30 DAY CAUSE INJURY TO EITHER LIVER, KIDNEY,
SPLEEN OR TESTES.
Medical Cond Aggravated by Exposure:NOT APPLICABLE.

First Aid:INGEST: DO NOT INDUCE VOMIT. EYES: FLUSH IMMED W/PLENTY OF
WATER FOR AT LEAST 15 MIN. SKIN: FLUSH IMMED W/PLENTY OF WATER
FOLLOWED BY WASHING W/SOAP & WATER. INHAL: REMOVE TO FRESH AIR.
APPLY ARTF RES P & OTHER SUPPORTIVE MEASURES AS REQD. OTHER: IF
INGEST, ANY TYPE OF OVEREXP OR SYMPS OF OVEREXP OCCUR DURING OR
FOLLOWING USE OF PROD, CNTCT POIS CTL CTR, EMER ROOM OR MD IMMED;
HAVE MSDS INFO AVAIL.

Flash Point Method:PMCC
Extinguishing Media:USE NFPA CLASS B EXTINGS (CARBON DIOXIDE, DRY
CHEM/UNIVERSAL AQ FILM FORMING FOAM) DESIGNED TO EXTING NFPA
(SUPDAT)
Fire Fighting Procedures:USE NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP .
WATER SPRAY MAY BE INEFTIVE. WATER SPRAY MAY BE USED TO COOL CLSD
CNTNRS TO PVNT PRESS BUILDUP & (SUPDAT)
Unusual Fire/Explosion Hazard:CLOSED CONTAINERS MAY EXPLODE OR BURST
(DUE TO THE BUILDUP OF STEAM PRESSURE) WHEN EXPOSED TO EXTREME
HEAT.

Spill Release Procedures:PROVIDE MAX VENT. ONLY PERS EQUIPPED WITH
PROPER NIOSH/MSHA APPRVD RESP & SKIN & EYE PROT SHOULD BE PEMITTED
IN AREA. REMOVE ALL SOURCES OF IGNIT. TAKE UP SPILLED MATL
W/SAWDUST, VERMICULITE OR OTHER ABSORB MATL & PLACE INTO CNTNRS
FOR DISP.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:DO NOT STORE ABOVE 120F. STORE LG QTYS
IN BUILDINGS DESIGNED & PROTECTED FOR STORAGE OF NFPA CLASS IIIB
COMBUSTIBLE LIQUIDS. PROTECT FROM FREEZING.
Other Precautions:IF THIS MATERIAL IS PART OF A MULTIPLE COMPONENT
SYSTEM, READ THE MSDS FOR THE OTHER COMPONENT OR COMPONENTS BEFORE
BLENDING AS THE RESULTING MIXTURES MAY HAVE THE HAZARDS OF ALL OF
ITS PARTS.

Respiratory Protection:WHERE VENTILATION IS INADEQUATE, USE A SUITABLE,
NIOSH/MSHA APPROVED RESPIRATOR.
Ventilation:PROVIDE GEN DILUTION OR LOC EXHST VENT IN VOL & PATTERN TO
KEEP CONC OF LISTED INGREDS BELOW THE LOWEST (SUPDAT)
Protective Gloves:NITRILE, NEOPRENE OR LATEX GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPROVED EYE WASH & DELUGE SHOWER .
WEAR PROTECTIVE CLOTHING INCLUDING IMPERMEABLE APRON.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXTING MEDIA: CLASS IIIB COMBUST LIQ FIRES. FIRE FIGHT PROCS: POSS
AUTOIGNIT OR EXPLO WHEN EXPOSED TO EXTREME HEAT. IF WATER IS USED,
FOG NOZZS ARE PREF. VENT: SUGGESTED EXPOS LIMITS, LEL BELOW STATED
LIMIT & TO REMOVE DECOMP PRODS DURING WELDING OR FLAME CUTTING.

Boiling Pt:B.P. Text:>212F,>100C
Vapor Pres:17.3
Vapor Density:HVR/AIR
Spec Gravity:1.10
Evaporation Rate & Reference:39 (BUAC=100)
Solubility in Water:74.4%
Appearance and Odor:VISCOUS LIQ W/ODOR CHARACTERISTIC OF CHEM FAMILY &
ANY SOLVS LISTED IN INGREDS.
Percent Volatiles by Volume:49.40

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRDCE HAZ DECOMP PRODS WHEN
HEATED. WELDING, BRAZING OR FLAME CUTTING MAY PRDCE FUMES INCLUDING
CARBON MONOXIDE.

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE, PROVINCIAL AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WAS TE MANAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.