CBNBP - ENERGIZED ROSIN CORE SOLDER, TLR
- MSDS: CBNBP
- Manufacturer: SPC TECHNOLOGY
- Product Name: ENERGIZED ROSIN CORE SOLDER, TLR
- National Stock Number: 3439-00N071061
Product Identification
Product ID:ENERGIZED ROSIN CORE SOLDER, TLR
MSDS Date:02/01/1992
FSC:3439
NIIN:00N071061
MSDS Number: CBNBP
Responsible Party
CHICAGO, IL 60640-4496
US
Emergency Phone: 312-907-5184
Info Phone: 312-907-5184
Cage: 12341
Contractor
Cage: 63590
Ingredients
LEAD (SARA 313) (CERCLA)
CAS: 7439-92-1
RTECS: OF7525000
Fraction By Weight: 30-60%
OSHA PEL SEE 1910.1025
ACGIH TLV: 0.15MG/M3 DUST
EPA Report Quantity: 1 LB
DOT Report Quantity: 1 LB
TIN
CAS: 7440-31-5
RTECS: XP7320000
Fraction By Weight: 40-70%
OSHA PEL 2 MG/M3
ACGIH TLV: 2 MG/M3
ROSIN ACID; (ROSIN)
CAS: 8050-09-7
RTECS: VL0480000
Fraction By Weight: 1-5%
OSHA PEL N/K
ACGIH TLV: N/K
Hazards
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE:EYE IRRIT. CHRONIC:RESP. SHORT
TERM OVEREXP TO FUMES MAY RSLT IN DIZZ, NAUS, OR DRYNESS/IRRIT OF
NOSE, THROAT, EYES/RESP SYS. CHRONIC EXCESS FUMES ABOVE PEL/TLV MAY
BE HAZ. MAY CAUSE IRRIT OF SK IN. HARMFUL/FATAL IF SWALLOWED. EXPER
TERATOGEN. MAY CAUSE BIRTH DEFECTS. EXCESS DUSTS & FUMES ARE (EFTS
OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZS:INHAL HAZ TO LUNGS & KIDNEYS. LEAD
APPEARS ON NAVY OCCUP CHEM REPRO HAZ LIST. SEEK CONSULTATION FROM
APPROP HLTH PROFESSIONALS CONCERNING LATEST HAZ LIST INFO & SAFE
HNDLG & EXPOS INFO (FP N ). "WARNING:USING PROD WILL EXPOSE YOU TO
CHEM (OR CHEMS) KNOWN TO CA TO CAUSE CANCER/BIRTH DEFECTS/OTHER
REPRO HARM".
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.
First Aid
First Aid:EYES:IMMEDIATELY FLUSH WITH PLENTY OF WATER FOR AT LEAST 15
MINUTES AND CALL A PHYSICIAN. SKIN:WASH THOROUGHLY WITH PLENTY OF
WATER/SOAP. INHALATION:IF AFFECTED, REMOVE TO FRESH AIR, ADMINISTER
OXYGEN AND CALL PHYSICIAN. INGESTION:SEEK PHYSICIAN IMMEDIATELY,
SHOW MSDS/LABEL, DO NOT INDUCE VOMITING.
Fire Fighting
Flash Point Method:PMCC
Flash Point:>200F,>93C
Extinguishing Media:WATER/FOG/FOAM/DRY CHEMICAL/CARBON DIOXIDE.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:CONTACT WITH FLAMES OR HOT SURFACES MAY
PRODUCE TOXIC GASES. COMBUSTION PRODUCTS:PBO, SNO, CO, CO*2.
Accidental Release
Spill Release Procedures:SOLID AT ROOM TEMPERATURE. IF IN MOLTEN STATE
ALLOW TO COOL AND SOLIDIFY AND THEN SCRAPE UP OR VACUUM. VENTILATE
THE AREA. PUT IN A SEALED APPROVED CONTAINER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:NO SPECIAL REQS FOR STOR. USE ONLY IN
WELL VENTD AREAS. AVOID PRLNGD/RPTD BRTHG OF GAS, FUMES, VAPS/SPRAY
MIST. AVOID CONT W/EYES & SKIN.
Other Precautions:CONT W/FLAME/HOT SURFS MAY PRDCE TOX GASES. DO NOT
TAKE INTERNALLY. IN CASE OF ACCIDENT OR ILLNESS, SEEK MD IMMED &
SHOW LBL/MSDS. MOLTEN LEAD ALLOY SOLDERS CONSISTING OF TIN DO NOT
PRDCE SIGNIFICANT QTY OF FUMES <600F. WHEN AIR OF (SUPDAT)
Exposure Controls
Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE
FOR EXPOSURE OF CONCERN . USE ONLY IN WELL VENTILATED AREA. IF
VENTILATION IS INADEQUATE, WEAR NIOSH/MSHA APPROVED RESPIRATORY
EQUIPMENT.
Ventilation:LOCAL AND MECHANICAL:REQUIRED. SPECIAL:WELDERS, ANSI Z49.1.
Protective Gloves:WELDERS GLOVES.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS(SUPDAT)
Other Protective Equipment:ANSI APPROVED EMERGENCY EYE WASH AND DELUGE
SHOWER .
Work Hygienic Practices:WASH THOROUGHLY AFTER USING.
Supplemental Safety and Health
OTHER PRECS:WORKROOMS REGULARLY CNTN NOT MORE THAN 50 UG/M3 OF INORG
CMPDS AS MEASURED BY PRESCRIBED METHS, CASES OF LEAD INTOX WILL NOT
OCCUR. EYE PROT:AND FULL LENGTH FACESHIELD .
Chemical Properties
Vapor Density:>1
Evaporation Rate & Reference:1 (WATER=1)
Solubility in Water:INSOLUBLE
Appearance and Odor:SILVER-GRAY, ODORLESS, FLUX CORE WIRE.
Percent Volatiles by Volume:70-75
Stability
Stability Indicator/Materials to Avoid:YES
OXIDIZING MATERIALS, STRONG ACIDS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:CO, ABIETIC ACID, ALIPHATIC ALDEHYDES
AND DITERPENE ACIDS.
Disposal
Waste Disposal Methods:DISPOSE OF WASTE IN ACCORDANCE WITH FEDERAL,
STATE AND LOCAL REGULATIONS. HAZARDOUS WASTE NUMBER:D008.REPORT
QUANTITY:2 LBS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.