Product ID:AMBERSEP 900 OH RESIN, 63248
MSDS Date:11/05/1991
FSC:6810
NIIN:00N073119
MSDS Number: CBZPQ

ROHM AND HAAS CO

100 INDEPENDENCE MALL WEST
PHILADELPHIA, PA 19106-2399
US

Emergency Phone: 215-592-3000;800-424-9300(CHEMTREC)

Info Phone: 215-592-3000

Cage: 77902

ROHM AND HAAS CO

PHILADELPHIA, PA 19106-2399 US

Telephone: 215-592-2521/215-592-3000

Cage: 77902

STRONG BASE ANION EXCHANGE POLYMER, HYDROXIDE ION FORM;

CAS: 9017-79-2

Fraction By Weight: 35-55%

OSHA PEL N/K

ACGIH TLV: N/K

WATER

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 45-65%

OSHA PEL N/K

ACGIH TLV: N/K

IRRIT. PROPERLY DESIGNED EQUIP IS VITAL IF THESE

RTECS: 9999999ZZ

STRONG OXIDIZING AGENTS SUCH AS NITRIC ACID TO PVNT

RTECS: 9999999ZZ

KNOWLEDGEABLE IN HNDLG OF THESE MATLS BEFORE

RTECS: 9999999ZZ

BEADS EXPAND WHEN WETTED; THIS EXPANSION CAN CAUSE

RTECS: 9999999ZZ

SUITABLE NIOSH APPROVED DUST/MIST AIR-PURIFYING

RTECS: 9999999ZZ

MANUAL OF REC PRACTICE PUBLISHED BY ACGIH FOR

RTECS: 9999999ZZ

NONE REQD UNDER NORMAL OPERATING CNDTNS. WORKER EXPOS

RTECS: 9999999ZZ

AT THE POINT OF DUST GENERATION.

RTECS: 9999999ZZ

GLOVES SHOULD BE REMOVED & REPLACED IMMED IF

RTECS: 9999999ZZ

CONTROLLED W/USE OF SUITABLE PERSONAL

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYE CONTACT:MATERIAL CAN CAUSE
IRRITATION. SKIN CONTACT:PROLONGED OR REPEATED CONTACT CAN CAUSE
SLIGHT IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:INGEST:CALL MD IMMEDIATELY . INHAL:REMOVE TO FRESH AIR.
SUPPORT BREATHING (GIVE O*2/ARTF RESP) . EYES:FLUSH W/LARGE AMOUNT
OF WATER FOR AT LEAST 15 MINUTES. CONSULT MD IF IRRITATION PERSIS
TS. SKIN:WASH AFFECTED AREAS THOROUGHLYW/SOAP & WATER.

Extinguishing Media:USE FOLLOWING EXTING MEDIA WHEN FIGHTING FIRES
INVOLVING THIS MATL: CARBON DIOXIDE, DRY CHEMICAL, WATER SPRAY.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:COMBUSTION GENERATES TOXIC FUMES OF THE
FOLLOWING: NITROGEN OXIDES.

Spill Release Procedures:WEAR GLOVES MADE OF BUTYL RUBBER. ADDNL
PERSONAL PROT EQUIP SHOULD INCL SFTY GLASSES (ANSI Z87.1/APPRVD
EQUIV). FLOOR MAY BE SLIPPERY; USE CARE TO AVOID FALLING. TRANSFER
SPILLED MATL TO SUITABLE CNTN RS FOR RECOVERY/DISP. RELS OF THIS
MATLTO(SUPDAT)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:MIN REC STOR TEMP FOR THIS MATL IS
0C/32F. MAX REC STOR TEMP FOR THIS MATL IS 49C/120F. KEEP FROM
FREEZING; MATL STABILITY MAY BE AFFECTED.
Other Precautions:MAX REC OPERATING TEMP FOR THIS MATL IS 60C/140F.
NOTE:THIS PROD AS SUPPLIED IS WHOLE BEAD ION EXCHANGE RESIN & MAY
PRDCE SLIGHT EYE IRRIT. HOWEVER, GROUND FORM OF THIS STRONG BASE
ANION EXCHANGE RESI N SHOULD BE TREATED AS SEV EYE (ING 3)

Respiratory Protection:RESP PROT PROGRAM MEETING OSHA 1910.134 & ANSI
Z88.2 REQUIREMENTS MUST BE FOLLOWED WHENEVER WORKPLACE CNDTNS
WARRANT RESP'S USE. NONE REQD UNDER NORMAL OPERATING CNDTNS. WORKER
EXPOS TO GROUND RESINS CAN BE CONTROLLED W/USE OF (ING 7)
Ventilation:VENT SYS EMPLOYED IS DEPENDENT ON USER'S SPECIFIC
APPLICATION OF THIS MATL. REFER TO CURRENT EDITION OF INDUS (ING 8)
Protective Gloves:CHEMICALLY RESISTANT GLOVES. (ING 11)
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EYE WASH FOUNTAIN & DELUGE SHOWER WHICH MEET
ANSI DESIGN CRITERIA . WORKER EXPOS TO GROUND RESINS CAN BE (ING
12)
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
PH:9.5-11 AQ SLURRY. SPILL PROC:AIR, LAND/WATER ARE NOT REPORTABLE TO
NRC UNDER CERCLA/TO STATE & LOC EMER PLANNING COMMITTEES UNDER SARA
TITLE III SECTION 304. WASTE DISP METH:DEFINITION OF IGNITABIL ITY,
CORROSIVITY/REACTIVITY & IS NOT LISTED IN 40 CFR 261.33. TOX
CHARACT, HOWEVER, HAS NOT BEEN EVALUATED BY TCLP.

Boiling Pt:B.P. Text:212F,100C
Melt/Freeze Pt:M.P/F.P Text:32.0F,0.0C
Vapor Pres:17 @ 20C
Vapor Density:<1
Spec Gravity:1-1.4 (H*2O=1)
pH:SUPDAT
Evaporation Rate & Reference:<1 (BUTYL ACETATE=1)
Solubility in Water:PRACTIALLY INSOLUBLE
Appearance and Odor:BEADS.
Percent Volatiles by Volume:45-65

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT W/STRONG OXIDIZING AGENTS, PARTICULARLY CONCENTRATED
NITRIC ACID.
Stability Condition to Avoid:AVOID TEMPERATURES >200C/392F.
Hazardous Decomposition Products:THERMAL DECOMPOSITION MAY YIELD
FOLLOWING: DIVINYLBENZENE, STYRENE MONOMER, ALKYLAMINES, OXIDES OF
NITROGEN.

Waste Disposal Methods:UNUSED RESIN MAY BE INCIN/LANDFILLED IN
FACILITIES MEETING LOC, STATE & FED REGS. FOR CONTAM RESIN, USER
MUST DETERM HAZ & USE APPROP DISP METH. WHEN DECISION IS MADE TO
DISCARD THIS MATL AS SUPPLIED, IT DOES NOT MEET RCRA'S CHARACT
(SUPP DATA)

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.