CCFRC - ALUMNIGRIP LINEAR POLYURETHANE TOPCOAT-COLOR BASE
- MSDS: CCFRC
- Manufacturer: US PAINT CORP (FORMERLY GROU GROUP INC)
- Product Name: ALUMNIGRIP LINEAR POLYURETHANE TOPCOAT-COLOR BASE
- National Stock Number: 8010-00F051753
Product Identification
Product ID:ALUMNIGRIP LINEAR POLYURETHANE TOPCOAT-COLOR BASE
MSDS Date:03/22/1991
FSC:8010
NIIN:00F051753
MSDS Number: CCFRC
Responsible Party
ST LOUIS, MO 63103-3043
US
Emergency Phone: 314-621-0525/202-483-7616
Info Phone: 314-621-0525/202-483-7616
Cage: EO831
Contractor
Telephone: 314-621-0525
Cage: EO831
Ingredients
XYLENE, DIMETHYLBENZENE, XYLOL (IARC - GROUP 3) *96-3*
CAS: 1330-20-7
RTECS: ZE2100000
Fraction By Weight: 3-5%
OSHA PEL 100 PPM
ACGIH TLV: 100 PPM, SKIN
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
LEAD CHROMATE, LEAD CHROMIUM OXIDE (SUSPECTED HUMAN
CAS: 7758-97-6
RTECS: GB2975000
Fraction By Weight: 0-37%
OSHA PEL 0.1 MG/CUM (CRO3)
ACGIH TLV: 0.05 MG/CUM (PB)
CELLOSOLVE ACETATE (ETHYLENE GLYCOL ETHYL ETHER ACETATE),
CAS: 111-15-9
RTECS: KK8225000
Fraction By Weight: 16-27%
OSHA PEL 100 PPM
ACGIH TLV: 5 PPM SKIN
DIISOBUTYL KETONE
CAS: 108-83-8
RTECS: MJ5775000
Fraction By Weight: 2-4%
OSHA PEL 50 PPM
ACGIH TLV: 145 MG/CUM
PROPYLENEGLYCOL MONOMETHYL ETHER ACETATE,
CAS: 108-65-6
RTECS: AI8925000
Fraction By Weight: 5-21%
Hazards
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:HARMFUL/FATAL IF
SWALLOWED/INHALED/ABSORBED. INHALATION: DISEASES OF THE LUNGS,
MUCOUS MEMBRANE IRRITATION, LEAD POISONING. INGESTION: NARCOTIC,
INJURY TO KIDNEYS/LIVER/LUNGS/COMA/CNS DEPRESSION, HEMO RRHAGES
INTO VITAL ORGANS. EYES: CORNEAL EFFECTS, SEVERE IRRITATION. SKIN:
DERMATITIS/MODERATE IRRITATION.
Explanation of Carcinogenicity:SEE INGREDIENTS
Effects of Overexposure:IRRITATION, TEARING, REDDENING, BLURRED,
SWELLING, SCALING, BLISTERING, DIZZINESS, WEAKNESS, FATIGUE,
NAUSEA, HEADACHE, UNCONSCIOUSNESS, SENSATION, VOMITING, DIARRHEA,
BURNING, SORE THROAT, ABDOMINAL PAIN.
First Aid
First Aid:SKIN: WASH THOROUGHLY W/SOAP & WATER. EYES: FLUSH W/LARGE
AMOUNTS OF WATER FOR 15 MINS. INGESTION: DON'T INDUCE VOMITING.
INHALATION: REMOVE TO FRESH AIR. IF BREATHING HAS STOPPED, GIVE
CPR. IF BREATH ING IS DIFFICULT, GIVE OXYGEN. OBTAIN MEDICAL
ATTENTION IN ALL CASES.
Fire Fighting
Flash Point Method:TCC
Flash Point:82F
Lower Limits:1.1
Upper Limits:7
Extinguishing Media:DRY CHEMICAL, FOAM.
Fire Fighting Procedures:USE W/FULL FACEPIECE OPERATER IN POSITIVE
PRESSURE MODE. CLOSED CONTAINER MAY EXPLODE DUE TO EXTREME HEAT.
Unusual Fire/Explosion Hazard:DON'T SMOKE. EXTINGUISH ALL PILOT LIGHTS
& TURN OFF ALL SOURCES OF IGNITION, INCLUDING HEATERS & OTHER NON
EXPLOSION PROOF ELECTRICAL EQUIPMENT.
Accidental Release
Spill Release Procedures:SMALL: ABSORB ON INERT MATERIAL SUCH AS PAPER,
VERMICULITE, FLOOR ABSORBENT & TRANSFER TO HOOD. LARGE: ELIMINATE
ALL IGNITION SOURCES. EVACUATE ALL UNPROTECTED PERSONNEL. STOP AT
SOURCE. CONTAIN TO PR EVENT SPREADING. PUMP TO SALVAGE TANK.
Handling
Handling and Storage Precautions:KEEP CLOSURE TIGHT & UPRIGHT. KEEP
CLOSED WHEN NOT IN USE. DON'T STORE >120F. CONTAINERS MAY CONTAIN
PRODUCT RESIDUE.
Exposure Controls
Respiratory Protection:WEAR APPROPRIATE, PROPERLY FITTED RESPIRATOR
UNTIL VAPOR/MIST & PARTICULATE LEVELS ARE BELOW APPLICABLE LIMITS.
Ventilation:ADEQUATE.
Protective Gloves:IMPERMEABLE
Eye Protection:SOLVENT RESISTANT W/SPLASH GUARDS.
Supplemental Safety and Health
Chemical Properties
Boiling Pt:B.P. Text:278-343F
Vapor Density:>1
Spec Gravity:1.04-1.54
pH:50-63
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:71
Stability
Stability Indicator/Materials to Avoid:YES
OXIDIZING MATERIALS, POTASSIUM-TERT-BUTOXIDE, PERMANGANATE, CHLOROFORM,
CHLOROSULFONIC ACID, HYDROGEN PEROXIDE.
Stability Condition to Avoid:EXCESS HEAT.
Hazardous Decomposition Products:CO, CO2, OXIDES OF NITROGEN.
Disposal
Waste Disposal Methods:DISPOSE OF IAW/FEDERAL, STATE & LOCAL
REGULATIONS. ALLOW VOLATILE PORTION TO EVAPORATE IN HOOD BEING SURE
TO ALLOW SUFFICIENT TIME FOR VAPORS TO COMPLETE CLEAR HOOD DUCT
WORK.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.