Product ID:P/N 08600 (ACCELERATOR PB) SHORT CUT AUTO GLASS ADHESIVE/SEA
MSDS Date:01/29/1993
FSC:8040
NIIN:00D020016
Kit Part:Y
MSDS Number: CCJKR

MINNESOTA MINING AND MFG CO AUTOMOTIVE TRADES DIV

3M CTR
ST PAUL, MN 55144-1000
US

Emergency Phone: 612-773-1110

Info Phone: 612-733-1110

Cage: 52157

NAPA, A DIVISION OF LINCOLN AUTOMOTIVE

ST. LOUIS, MO 63120-1578 US

Telephone: 414-255-5520

Cage: 050Q3

URETHANE PREPOLYMER

CAS: 68610-33-3

Fraction By Weight: 50-60%

METHYLENE BISPHENYL ISOCYANATE (MDI) (SARA 313)

CAS: 101-68-8

RTECS: NQ9350000

Fraction By Weight: 20-30%

OSHA PEL C 0.02 PPM

ACGIH TLV: 0.005 PPM; 9596

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

HYDROGENATED TERPHENYLS

CAS: 61788-32-7

RTECS: WZ6535000

Fraction By Weight: 10-20%

OSHA PEL 0.5 PPM

ACGIH TLV: 0.5 PPM; 9596

DIMETHYL SILOXANE, REACTION PRODUCT WITH SILICA OR SILICON

CAS: 67762-90-7

Fraction By Weight: 1-10%

OSHA PEL 6 MG/M3

ACGIH TLV: 10 MG/M3

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: EXPOSURE MAY CAUSE EYE, SKIN &
RESPIRATORY TRACT IRRITATION; MAY CAUSE ALLERGIC SKIN/RESPIRATORY
REACTION. INGESTION MAY CAUSE GI TRACT IRRITATION. CHRONIC: NONE
SPECIFIED BY MANUFACTURER.
Explanation of Carcinogenicity:NO INGREDIENT OF A CONCENTRATION OF 0.1%
OR GREATER IS LISTED AS A CARCINOGEN OR SUSPECTED CARCINOGEN.
Effects of Overexposure:EYES-IRRITATION, REDNESS, SWELLING, PAIN,
TEARING, HAZY VISION. SKIN-IRRITATION, REDNESS, SWELLING, ITCHING.
INHALED-IRRITATION, SORENESS OF THROAT/NOSE, COUGHING, SNEEZING.
INGESTED-GI TRACT IRRITATI ON, PAIN, VOMITING, ABDOMINAL
TENDERNESS, NAUSEA, BLOOD IN VOMITUS, BLOOD IN FECES.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid:IN ALL CASES GET MEDICAL ATTENTION. EYES-FLUSH WITH WATER FOR
15 MINUTES. SKIN-FLUSH WITH LOTS OF WATER. INHALED-REMOVE TO FRESH
AIR. INGESTED-DO NOT INDUCE VOMITING! IF CONSCIOUS, DRINK 2 GLASSES
WAT ER. CALL A PHYSICIAN.

Extinguishing Media:WATER, CARBON DIOXIDE, DRY CHEMICAL, FOAM.
Fire Fighting Procedures:WEAR SELF-CONTAINED BREATHING APPARATUS AND
FULL FIRE FIGHTER'S PROTECTIVE GEAR.
Unusual Fire/Explosion Hazard:NONE KNOWN.

Spill Release Procedures:REFER TO OTHER MSDS SECTIONS FOR ADVICE ON
PHYSICAL & HEALTH HAZARDS, RESPIRATORY PROTECTION, VENTILATION, &
PERSONAL PROTECTIVE EQUIPMENT. CALL 612-733-1110/733-6100 FOR 24-HR
SPILL ASSISTANCE. COLLE CT SPILLED MATERIAL, PLACE IN CONTAINER&
SEAL.
Neutralizing Agent:90% WATER+8% CONCENTRATED AMMONIUM HYDROXIDE+2%
DETERGENT

Handling and Storage Precautions:COMBUSTIBLE! KEEP CONTAINER TIGHTLY
CLOSED. KEEP OUT OF REACH OF CHILDREN. USE IN A WELL-VENTILATED
AREA. AVOID SKIN CONTACT. AVOID EYE CONTACT.
Other Precautions:DO NOT INGEST. AVOID PROLONGED BREATHING OF PRODUCT.
WHEN THIS BASE IS USED IN COMBINATION WITH THE ACCELERATOR FOLLOW
THE PRECAUTIONS OUTLINED IN THE ACCELERATOR MATERIAL DATA SHEET.

Respiratory Protection:IF ENGINEERING CONTROLS FAIL OR NON-ROUTINE USE
OR AN EMERGENCY OCCURS; WEAR AN MSHA/NIOSH APPROVED AIR-SUPPLIED
RESPIRATOR OR SCBA, AS REQUIRED. USE IAW 29 CFR 1910.134.
Ventilation:USE IN A WELL-VENTILATED AREA. USE ADEQUATE MECHANICAL
VENTILATION OR LOCAL EXHAUST TO MAINTAIN EXPOSURE BELOW TLV(S).
Protective Gloves:IMPERVIOUS-PVA, TEFLON, VITON.
Eye Protection:SAFETY GLASSES/CHEMICAL SPLASH GOGGLES.
Other Protective Equipment:NONE SPECIFIED BY MANUFACTURER. DLA-HMIS:
EYE WASH STATION & SAFETY SHOWER.
Work Hygienic Practices:WASH HANDS AFTER HANDLING AND BEFORE EATING,
DRINKING, OR SMOKING. LAUNDER CONTAMINATED CLOTHES BEFORE REUSE.
Supplemental Safety and Health
KEY1=N1. THIS ACCELERATOR (PB-5025) USED WITH 3M SHORT-CUT AUTO GLASS
ADHESIVE/SEALANT P/N 08600 (BASE-PB); MFG #PB-5190, MSDS DOC
#1104065).

HCC:N1
Boiling Pt:B.P. Text:392F,200C
Vapor Pres:00.00
Vapor Density:8.60
Spec Gravity:1.010
Viscosity:PASTE
Appearance and Odor:THIXOPTROPIC PASTE, WHITE (TRANSLUCENT); PUNGENT
ODOR.
Percent Volatiles by Volume:0.00

Stability Indicator/Materials to Avoid:YES
AMINES, ALCOHOLS, WATER. REACTION WITH AMINES, ALCOHOLS & WATER NOT
HAZARDOUS IF CONTAINER CAN VENT TO ATMOSPHERE.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE,
OXIDES OF NITROGEN, HYDROGEN CYANIDE, ISOCYANATES, TOXIC VAPORS,
GASES OR PARTICULATES.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

Waste Disposal Methods:CURE PRODUCT IAW PRODUCT INSTRUCTIONS.
INCINERATE IN AN INDUSTRIAL OR COMMERCIAL FACILITY IN THE PRESENCE
OF A COMBUSTIBLE MATERIAL. DISPOSE OF COMPLETELY CURED (OR
POLYMERIZED) MATERIAL IN A SANITARY LANDFILL.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.