Product ID:EUTROLOY 16006G
MSDS Date:09/07/1995
FSC:3439
NIIN:00N071739
MSDS Number: CDWSP

EUTECTIC CORP

1515 BROOK DR
DOWNERS GROVE, IL 60515
US

Emergency Phone: 800-323-4845

Info Phone: 800-323-4845

Cage: 72271

EUTECTIC CORPORATION

DOWNERS GROVE, IL 60515 US

Telephone: 800-323-4845

Cage: 5N977

COBALT (SARA 313)

CAS: 7440-48-4

RTECS: GF8750000

Fraction By Weight: 60-70%

OSHA PEL 0.1 MG/M3

ACGIH TLV: 0.02 MG/M3; A3

CHROMIUM (SARA 313) (CERCLA)

CAS: 7440-47-3

RTECS: GB4200000

Fraction By Weight: 20-30%

OSHA PEL 1 MG/M3

ACGIH TLV: 0.5 MG/M3

EPA Report Quantity: 1 LB

DOT Report Quantity: 1 LB

TUNGSTEN

CAS: 7440-33-7

RTECS: YO7175000

OSHA PEL 5 MG/M3 (MFR)

ACGIH TLV: 1 MG/M3/3 STEL

GRAPHITE, SYNTHETIC; (CARBON)

CAS: 7440-44-0

RTECS: FF5250100

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 2 MG/M3 TDUST

SILICON

CAS: 7440-21-3

RTECS: VW0400000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST

NICKEL (SARA 313) (CERCLA)

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: 1-5%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3

IRON

CAS: 7439-89-6

RTECS: NO4565500

OSHA PEL 15 MG/M3 (MFR)

ACGIH TLV: 10 MG/M3 (MFR)

FORM FROM INGS. REASONABLY EXPECTED

RTECS: 9999999ZZ

IN INGS. FLUX COATINGS MAY PRDCE FLUORIDE CMPDS,

RTECS: 9999999ZZ

INCL OZONE, CARBON MONOXIDE & DIOXIDE, NITROGEN

RTECS: 9999999ZZ

ONE WAY TO DETERMINE COMPOSITION & QTY OF FUMES &

RTECS: 9999999ZZ

INSIDE WORKER'S HELMET OR BREATHING ZONE.

RTECS: 9999999ZZ

IARC MONO ON EVAL OF CARCIN RISK

RTECS: 9999999ZZ

NTP 7TH ANNUAL REPORT ON CARCINOGENS, 1994

RTECS: 9999999ZZ

NAUS/DRYNESS/IRRIT OF NOSE, THROAT/EYES.

RTECS: 9999999ZZ

PNEUMOCONIOSIS/SIDEROSIS (IRON DEPOSITS IN LUNG).

RTECS: 9999999ZZ

METALLIC CMPDS DURING WELDING, HEATING, BRAZING,

RTECS: 9999999ZZ

HEAD & MUSC ACHE, TIGHTNESS OF CHEST, DRYNESS OF

RTECS: 9999999ZZ

OCCUR W/IN SEVERAL HRS AFTER OVEREXP & MAY LAST

RTECS: 9999999ZZ

LONG TERM

RTECS: 9999999ZZ

OVEREXP MAY

RTECS: 9999999ZZ

INHAL CAN CAUSE PNEUMOCONIOSIS/NON DISABLING

RTECS: 9999999ZZ

FILTER LENS. PROVIDE PROT SCREENS & FLASH GOGG TO

RTECS: 9999999ZZ

SEE WELD ZONE, THEN GO TO NEXT LIGHTER SHADE WHICH

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INHAL: FUMES CAN BE DANGEROUS
TO YOUR HLTH & OVEREXP CAN CAUSE LUNG DMG &/OTHER ORGAN DMG.
EYE/SKIN: ARC RAYS & ULTRAVIOLET LIGHT CAN INJURE EYES & BURN SKIN.
LIQS USED IN FLUXES & CHEM AIDS MA Y CAUSE IRRIT/POSS CHEM BURNS.
ELEC SHOCK CAN KILL. INGEST: DANGER! MAY BE HARMFUL/FATAL IF
SWALLOWED. (EFTS OF OVEREXP)
Explanation of Carcinogenicity:COBALT: IARC MONO ON EVAL OF CARCIN RISK
OF CHEMICALS TO MAN, VOL 52, PG 363, 1991: GROUP 2B. ANIMAL: GI.
(ING 13)
Effects of Overexposure:HLTH HAZ: CHRONIC: GEN WELDING FUMES: ELEC ARC
WELDING, BRAZING, SOLDERING/THERMAL SPRAYING MAY CREATE ONE/MORE OF
THE FOLLOWING HLTH HAZ: FUMES, GASES & DUSTS CAN BE DANGEROUS TO
YOUR HLTH. CERTAIN M ED STUDIES HAVE SUGGESTED LUNG DMG CAN RSLT
FROM OVEREXP TO THOSE FUMES. SHORT TERM OVEREXP MAY RSLT IN DIZZ,
(ING 15)
Medical Cond Aggravated by Exposure:AGGRAVATION OF PREEXISTING
RESPIRATORY OR ALLERGIC CONDITIONS MAY OCCUR IN SOME WORKERS.

First Aid:INHAL: MOVE VICTIM TO FRESH AIR SOURCE. CONTACT MD & ADVISE
OF INGREDIENTS. SKIN: THOROUGHLY WASH HANDS/AFFECTED AREAS W/SOAP &
WATER TO REMOVE ALL RESIDUE. IF RASH/BURN DEVELOPS, CONSULT MD.
EYES: TH OROUGHLY FLUSH W/WATER FOR AT LEAST 15 MINUTES TO REMOVE
ALL RESIDUE. OBTAIN PROMPT MED ADVICE FOR FLUXES & CHEMICAL AIDS.
ADVISE MD OF INGS. INGEST: CALL MD &/LOCAL POISON CTL CTR. ADVISE
OF INGS.

Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:WEAR NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:GEN NON-FLAM WELDING ARC SPKS & FLAMES
CAN IGNITE COMBUST & FLAMS. METAL POWDER DUST MAY PRESENT
FIRE/EXPLO HAZ UNDER FAVORABLE CNDTNS OF PARTICLE SIZE(SUP DAT)

Spill Release Procedures:NONE SPECIFIED BY MANUFACTURER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:PLEASE READ AND UNDERSTAND THE PRODUCT
LABEL INFORMATION FOR PROPER PROCEDURES AND USE.
Other Precautions:SEE ANSI Z49.1 "SFTY IN WELDING & CUTTING" & CHAPTER
II OF "THERMAL SPRAYING" PUBLISHED BY AMERICAN WELDING SOCIETY &
OSHA PUBLICATION 2206 (29 CFR 1910) FOR MORE DETAIL. TRAIN WELDER
TO KEEP HIS/HER FACE AWAY FROM FUME/DUST PLUME.

Respiratory Protection:IF THE WORK STATION IS NOT PROPERLY VENTILATED
TO EXHAUST ALL FUMES, VAPORS AND DUSTS BELOW THE RECOMMENDED
EXPOSURE LIMITS, USE A NIOSH APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GEN VENT & LOC EXHST AT WORK SITE TO KEEP ALL
FUMES & DUSTS FROM WORKER'S BRTHG ZONE & GEN AREA.
Protective Gloves:WELDERS GLOVES.
Eye Protection:WEAR HELMET/USE FSHLD W/APPROP (ING 24)
Other Protective Equipment:ANSI APPRVD EYEWASH & DELUGE SHOWER . WEAR
ARM PROT, APRONS, HATS & DARK PROTECTIVE CLOTHING.
Work Hygienic Practices:TRAIN WORKERS NOT TO TOUCH LIVE ELECTRIC PARTS
& TO INSULATE THEMSELVES FROM WORK & ELECTRICAL GROUND.
Supplemental Safety and Health
EXPLO HAZ:DISPERSION & STRONG IGNIT SOURCE. WHEN PREPARING WORKPLACE
W/FLAM CHEM AID, KEEP ALL WELDING SOURCES, SPKS & FLAMES AT LEAST
20 FEET FROM WORKPLACE UNTIL FLAM EVAPS. TOX FUMES MAY BE PRDCED.
SOME FLUXES & CHEM AIDS MAY GIVE OFF HYDROGEN CHLORIDE, PHOSGENE &
CHLORINE GAS. CANS, UNDER PRESS, & FLAM MAY EXPLODE.

Appearance and Odor:NONE SPECIFIED BY MANUFACTURER

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:DURING WELDING, THERMAL SPRAYING &
ALLIED PROCESSES, FUME & GAS DECOMP PRODS GENERATED ARE DIFFERENT
IN PERCENT &(ING 7)

Waste Disposal Methods:DISPOSE OF WASTE MATERIAL, POWDERS,
GRINDING/FILLER RESIDUES IN AN ENVIRONMENTALLY SENSITIVE MANNER IN
ACCORDANCE WITH FEDERAL, STATE & LOCAL REGULATIONS. USE APPROP
MEASURES TO KEEP AIRBORNE DUST LEV ELS CONTAINED I/A/W EXPOS LEVELS
IN INGS SECTION.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.