CGCXC - GRAY CONCRETE CRACK SEAL, 8640

  • MSDS: CGCXC
  • Manufacturer: QUIKRETE COMPANIES
  • Product Name: GRAY CONCRETE CRACK SEAL, 8640
  • National Stock Number: 5610-00N082431
Product Identification

Product ID:GRAY CONCRETE CRACK SEAL, 8640
MSDS Date:07/15/1996
FSC:5610
NIIN:00N082431
MSDS Number: CGCXC

Responsible Party
QUIKRETE COMPANIES
2987 CLAIRMONT RD SUITE 500
ATLANTA, GA 30329
US

Emergency Phone: 770-216-9580

Info Phone: 770-216-9580

Cage: IO174

Contractor
QUIKRETE COMPANIES
ATLANTA, GA 30345 US

Telephone: 404-634-9100

Cage: IO174

Ingredients

ACRYLIC POLYMER

CAS: 25068-63-7

OSHA PEL N/K

ACGIH TLV: N/K


1,2-PROPANEDIOL; (PROPYLENE GLYCOL)

CAS: 57-55-6

RTECS: TY2000000

OSHA PEL N/K

ACGIH TLV: N/K


CALCIUM CARBONATE; (LIMESTONE/MARBLE)

CAS: 1317-65-3

RTECS: EV9580000

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST


PROPIONIC ACID, 2-METHYL-, MONOESTER

CAS: 25265-77-4

RTECS: UF6000000

OSHA PEL N/K

ACGIH TLV: N/K


IRON (III) OXIDE; (IRON OXIDE PIGMENTS)

CAS: 1309-37-1

RTECS: NO7400000

OSHA PEL 10 MG/M3 (FE)

ACGIH TLV: 5 MG/M3 FUME (FE)

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHALATION OF VAPOR OR MIST CAN CAUSE
FOLLOWING: HEADACHE, NAUSEA, IRRITATION OF NOSE, THROAT AND LUNGS.
EYE CONTACT:DIRECT CONTACT WITH MATERIAL CAN CAUSE IRRITATION AND
POSSIBLE CORNEAL INJURY. SKIN CONTACT:PROLONGED OR REPEATED
CONTACT CAN CAUSE SLIGHT IRRITATION.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

First Aid

First Aid:SKIN:THORO WASH AFFECTED AREA W/SOAP & WATER. REMOVE CONTAM
CLTHG. EYES:FLUSH W/LG AMTS OF WATER FOR AT LST 15 MINS, LIFTING
UPPER & LOWER LIDS OCCAS. GET MED ATTN. INGEST:GIVE 2 GLASSES OF
WATER. IF LG AMTS ARE INGESTED, INDUCE VOMIT W/IPECAC SYRUP/BY
PLACING FINGER AT BACK OF THROAT. NEVER GIVE ANYTHING BY MOUTH TO
UNCON PERS. GET MED ATTN. INHAL:REMOVE TO FRESH AIR IF EFTS OCCUR.
CONSULT MD.

Fire Fighting

Flash Point:248F,120C
Extinguishing Media:USE METHODS APPROPRIATE FOR SURROUNDING FIRE.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:THIS WATER BASED DISPERSION CAN SPLATTER
AT TEMPS >100C(212F). POLYMER FILM CAN BURN ONCE WATER HAS EVAP.
PROD ALSO MAY CNTN <1% OF SOLV W/FL PT OF 120C(248F).

Accidental Release

Spill Release Procedures:KEEP SPECTATORS AWAY. FLOOR MAY BE SLIPPERY;
USE CARE TO AVOID FALLING. CNTN SPILLS IMMED W/INERT MATLS (E.G.
SAND, EARTH). TRANSFER LIQS & SOLID DIKING MATLS TO SEPARATE
SUITABLE CNTNRS FOR RECOVERY/ DISP. CAUT:KEEP SPILLS & CLEANING
RUNOFF OUT OF MUNICIPAL SEWERS & OPEN BODIES OF WATER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:AVOID SKIN & EYE CONTACT & AVOID
BREATHING VAPORS. KEEP FROM FREEZING; MATERIAL MAY COAGULATE.
Other Precautions:MINIMUN RECOMMENDED STORAGE TEMPERATURE FOR THIS
MATERIAL IS 1C (34F). MAXIMUM RECOMMENDED STORAGE TEMPERATURE FOR
THIS MATERIAL IS 49C (120F).

Exposure Controls

Respiratory Protection:NIOSH APPROVED RESPIRATOR APPROPRIATE FOR
EXPOSURE OF CONCERN .
Ventilation:USE LOC EXHST VENT W/MIN CAPTURE VELOCITY OF 100 FT/MIN (30
M/MIN) AT POINT OF VAP EVOLUTION. REFER TO CURRENT EDITION OF
"INDUSTRIAL VENT:A MANUAL OF (SUPDAT)
Protective Gloves:NEOPRENE GLOVES. GLOVES OF OTHER CHEM RESIST MATLS
MAY NOT PROVIDE ADEQ PROT.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EYE WASH FOUNTAIN & DELUGE SHOWER WHICH MEET
ANSI DESIGN CRITERIA .
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
VENTILATION: REC PRACTICE" PUBLISHED BY ACGIH FOR INFO ON DESIGN,
INSTALLATION, USE & MAINT OF EXHST SYSTEMS.

Chemical Properties

Boiling Pt:B.P. Text:212F,100C
Melt/Freeze Pt:M.P/F.P Text:30.0F,-1.1C
Solubility in Water:DILUTABLE
Appearance and Odor:GRAY VISCOUS LIQUID W/SLIGHT ETHER & AMMONIA ODOR.

Stability

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT W/STRONG OXIDIZING AGENTS OR STRONG ALKALIES.
Stability Condition to Avoid:AVOID TEMPERATURES >177C (350F), ONSET OF
POLYMER DECOMPOSITION. THERMAL DECOMP IS DEPENDENT ON TIME &
TEMPERATURE.
Hazardous Decomposition Products:THERMAL DECOMPOSITION MAY YIELD
ACRYLIC MONOMERS.

Disposal

Waste Disposal Methods:COAGULATE EMULSION BY STEPWISE ADDITION OF
FERRIC CHLORIDE & LIME. REMOVE CLEAR SUPERNATANT & FLUSH TO
CHEMICAL SEWER. INCINERATE LIQUID & CONTAMINATED SOLIDS I/A/W
LOCAL, STATE & FEDERAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.