CGYZG - 186 ROSIN FLUX
- MSDS: CGYZG
- Manufacturer: KESTER SOLDER
- Product Name: 186 ROSIN FLUX
- National Stock Number: 3439-00N079141
Product Identification
Product ID:186 ROSIN FLUX
MSDS Date:07/31/1996
FSC:3439
NIIN:00N079141
MSDS Number: CGYZG
Responsible Party
DES PLAINES, IL 60018
US
Emergency Phone: 800-424-9300 (CHEMTREC)
Info Phone: 708-297-1600
Preparer: M WISE
Cage: GO345
Contractor
Telephone: 847-297-1600
Cage: 75297
Ingredients
ISOPROPYL ALCOHOL; (2-PROPANOL) (SARA 313)
CAS: 67-63-0
RTECS: NT8050000
Fraction By Weight: 61%
OSHA PEL 400 PPM
ACGIH TLV: 400 PPM/500STEL
ROSIN; (MODIFIED ROSIN)
CAS: 8050-09-7
RTECS: VL0480000
Fraction By Weight: 36%
OSHA PEL N/K
ACGIH TLV: N/K
NON-HAZARDOUS INGREDIENTS
OSHA PEL N/K
ACGIH TLV: N/K
Hazards
LD50 LC50 Mixture:LD50 (ORAL RAT): 5.8 G/KG.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:TARGET ORGANS: EYE, MUC MEMB & RESP
SYS. ACUTE: INHAL: FUMES DURING SOLDERING MAY IRRITATE MUC MEMB &
RESP SYS. HIGH CONCS CAN CAUSE HDCH, DIZZ, NARCOSIS & NAUS. SKIN
CONT: LOC IRRIT. SKIN ABSORPTION: NONE. EYE: IRRIT FROM CONT W/LIQ
& SMOKE FROM SOLDERING. INGEST: BURNING SENSATION IN DIGESTIVE
TRACT.(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ: CHRONIC: PRLNG/RPTD SKIN CONT CAN
RSLT IN RASH. BRTHG VAPS CAN RSLT IN HDCH, DIZZ, NARCOSIS & IRRIT
OF MUC MEMB. SMOKE DURING SOLDERING WILL CONTAIN ROSIN WHICH IS AN
ALLERGEN & CAN CAUSE RE SP IRRIT & DMG.
Medical Cond Aggravated by Exposure:CHEMICAL HYPERSENSITIVITY, ASTHMA
AND OTHER RESPIRATORY CONDITIONS. CONTINUED BREATHING OF HIGH
CONCENTRATIONS OF ALCOHOL VAPORS CAN AFFECT THE LIVER AND CENTRAL
NERVOUS SYSTEM.
First Aid
First Aid:EYES: FLUSH WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES AND
GET MEDICAL ATTENTION. REMOVE ROSIN FROM AROUND EYES WITH A DILUTE
ETHANOL SOLUTION. SKIN: WASH THOROUGHLY WITH SOAP AND WATER.
INHALATION: REMOVE VICTIM TO FRESH AIR. INGESTION:INDUCE VOMITING
AND GET PROMPT MEDICAL ATTENTION.
Fire Fighting
Flash Point Method:TOC
Flash Point:65.0F,18.3C
Lower Limits:2.0%
Upper Limits:12.0%
Extinguishing Media:CARBON DIOXIDE, ALCOHOL FOAM, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH APPROVED SCBA & FULL PROTECTIVE
EQUIPMENT . USE WATER SPRAY TO COOL FIRE-EXPOSED CONTAINERS AND
CONTROL VAPORS.
Unusual Fire/Explosion Hazard:A MODERATE EXPLOSION HAZARD EXISTS WHEN
EXPOSED TO HEAT OR FLAME.
Accidental Release
Spill Release Procedures:REMOVE ALL IGNITION SOURCES. PROVIDE ADEQUATE
VENTILATION. ABSORBENTS, SUCH AS VERMICULITE, CAN BE USED TO SOAK
UP THE SPILLED LIQUID. CLEAN UP RESIDUAL WITH ALKALINE DETERGENT.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
Handling
Handling and Storage Precautions:CAUTION: EMPTY CONTAINERS MAY CONTAIN
PRODUCT RESIDUE. OBSERVE ALL LABEL PRECAUTIONS. STORE AWAY FROM
SOURCES OF IGNITION.
Other Precautions:STORAGE AT TEMPERATURES BELOW 40F (4C) MAY RESULT IN
PRECIPITATION OF SOME ROSIN. OPEN CONTAINERS CAUTIOUSLY TO ALLOW
VENTING OF ANY INTERNAL PRESSURE.
Exposure Controls
Respiratory Protection:USUALLY NOT REQUIRED. WHEN VENTILATION IS NOT
ADEQUATE TO REMOVE SMOKE FROM THE BREATHING ZONE, A NIOSH APPROVED
CARTRIDGE TYPE RESPIRATOR SHOULD BE WORN.
Ventilation:PROVIDE ADEQUATE EXHAUST VENTILATION (GENERAL AND/OR LOCAL)
TO MEET TLV REQUIREMENTS.
Protective Gloves:PLASTIC OR RUBBER.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:EMERGENCY EYEWASH AND DELUGE SHOWER MEETING
ANSI DESIGN CRITERIA . IMPERMEABLE APRON WHEN SPLASHING.
Work Hygienic Practices:WASH HANDS THOROUGHLY BEFORE EATING OR SMOKING.
Supplemental Safety and Health
HAZ DECOM PROD: ROSIN MAY BE THERMALLY DEGRADED TO LIBERATE ALIPHATIC
ALDEHYDES, ACIDS & TERPENES.
Chemical Properties
Boiling Pt:B.P. Text:180F,82C
Vapor Pres:33 @ 20C
Vapor Density:2.1
Spec Gravity:0.879 (H*2O=1)
VOC Pounds/Gallon:562
Evaporation Rate & Reference:1.7 (BUTYL ACETATE=1)
Solubility in Water:55%
Appearance and Odor:AMBER LIQUID WITH ALCOHOL ODOR
Percent Volatiles by Volume:64
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING MATERIALS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:CARBON MONOXIDE, CARBON DIOXIDE,
ALDEHYDES & ACIDS. WHEN HEATED TO SOLDERING TEMPS, SOLVENTS ARE
EVAPORATED & (SUP DAT)
Disposal
Waste Disposal Methods:ACCORDING TO LOCAL REGULATIONS, USUALLY BY
INCINERATION. EPA HAZARDOUS WASTE NUMBER D001. HAZARD CLASS AS
IGNITABLE CLASS. DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE AND
FEDERAL REGULATIONS .
Other Information
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.