CHJCS - 14-110

  • MSDS: CHJCS
  • Manufacturer: PPG INDUSTRIES INC
  • Product Name: 14-110
  • National Stock Number: 8010-00N065492
Product Identification

Product ID:14-110
MSDS Date:11/29/1995
FSC:8010
NIIN:00N065492
MSDS Number: CHJCS

Responsible Party
PPG INDUSTRIES INC
4325 ROSANNA DR
ALLISON PARK, PA 15101
US

Emergency Phone: 800-441-9695

Info Phone: 412-492-5555

Cage: 47695

Contractor
PPG INDUSTRIES INC
PITTSBURGH, PA 15272 US

Telephone: 1-800-245-2974 (CAL HYPO)

Cage: 47695

Ingredients

CLAY (KAOLIN); (ALUMINUM SILICATE)

CAS: 1332-58-7

RTECS: GF1670500

Fraction By Weight: 10-<20%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 2 MG/M3 TDUST


TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 1-<5%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST


SILICA, CRYSTALLINE - CRISTOBALITE; (SILICA CRISTOBALITE)

CAS: 14464-46-1

RTECS: VV7325000

Fraction By Weight: 1-<5%

OSHA PEL N/K

ACGIH TLV: 0.05 MG/M3 RDUST


SILICA, CRYSTALLINE - QUARTZ; (QUARTZ)

CAS: 14808-60-7

RTECS: VV7330000

Fraction By Weight: 0.1-<1%

OSHA PEL N/K

ACGIH TLV: 0.1 MG/M3 RDUST


PROD COMES IN CONTACT W/EXTREME HEAT (SEE STABILITY

RTECS: 9999999ZZ


CARBON DIOXIDE; LOWER MOLECULAR WEIGHT

RTECS: 9999999ZZ


LIMITED TO, FLAME CUTTING, BRAZING AND WELDING.

RTECS: 9999999ZZ


ANTICIPATED TO BE CARCINOGEN.

RTECS: 9999999ZZ


W/HUMANS INVOLVED IN MFR OF THIS PIGMENT

RTECS: 9999999ZZ


POTENTIAL FOR INHAL OF TITANIUM DIOXIDE DUST FROM

RTECS: 9999999ZZ


TO FRESH AIR. APPLY ARTF RESP & OTHER

RTECS: 9999999ZZ


OVEREXP OR SYMPS OF OVEREXP OCCUR DURING OR

RTECS: 9999999ZZ


EMERGENCY ROOM OR MD IMMEDIATELY; HAVE MSDS INFO

RTECS: 9999999ZZ


CNTNRS FOR DISPOSAL. ONLY SPILLED MATL &

RTECS: 9999999ZZ


GROUNDED WHEN POURING. AVOID FREE FALL OF

RTECS: 9999999ZZ


SECTION BELOW THE LOWEST SUGGESTED EXPOSURE LIMITS,

RTECS: 9999999ZZ


PRODUCTS DURING WELDING OR FLAME CUTTING.

RTECS: 9999999ZZ


BEEN DONE ON PROTECTIVE CLTHG FOR THIS

RTECS: 9999999ZZ


INFREQUENT CONTACT W/THIS PROD. FOR FREQUENT

RTECS: 9999999ZZ


FOR APPROP CHEMICAL IMPERVIOUS EQUIPMENT.

RTECS: 9999999ZZ

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:YES IARC:YES OSHA:NO
Health Hazards Acute and Chronic:INGEST: MAY BE HARMFUL IF SWALLOWED.
EYE CONTACT: CAUSES EYE IRRIT. SKIN CONTACT: MAY CAUSE SLIGHT SKIN
IRRIT. INHAL: NONE KNOWN. SANDING & GRINDING DUSTS MAY BE HARMFUL
IF INHALED. CHRONIC: AVOID LON G-TERM & RPTD CONTACT. LONG-TERM
EXPOS TO CRYSTALLINE SILICA/QUARTZ MAY LEAD TO DISABLING INJURY
KNOWN (EFTS OF OVEREXP)
Explanation of Carcinogenicity:SILICA, CRYSTALLINE-QUARTZ &
-CRISTOBALITE: IARC MONO, VOL 68, 1997:GROUP 1. NTP 7TH ANNUAL
REPORT ON CARCINS, (ING 8)
Effects of Overexposure:HLTH HAZ: AS SILICOSIS. EFTS ARE ASSOC W/BRTHG
EXCESSIVE AMTS OF SILICA DUST. APPLICATION OF PROD IS NOT EXPECTED
TO GENERATE EXCESSIVE AMTS OF RESPIRABLE SILICA/QUARTZ. THIS PROD
CONTAINS TITANIUM DI OXIDE. ANIMALS INHALING MASSIVE QTYS
OFTITANIUM DIOXIDE DUST IN LONG-TERM STUDY DEVELOPED LUNG TUMORS.
STUDIES (ING 9)
Medical Cond Aggravated by Exposure:NOT APPLICABLE.

First Aid

First Aid:INGEST: IF SWALLOWED, DO NOT INDUCE VOMIT. GENTLY WIPE OUT
INSIDE MOUTH TO REMOVE ANY RESIDUAL MATL. EYES: IN CASE OF CONTACT,
REMOVE CONTACT LENSES & FLUSH EYES IMMED W/GENTLE STREAM OF
LUKEWARM WATE R FOR AT LEAST 15 MIN. SKIN: IN CASE OFCONTACT, FLUSH
IMMED W/PLENTY OF WATER FOR AT LEAST 15 MIN FOLLOWED BY WASHING
W/SOAP & WATER. INHAL: IF AFFECTED BY INHAL OF VAP/SPRAY MIST,
REMOVE (ING 11)

Fire Fighting

Extinguishing Media:USE EXTINGUISHERS APPROPRIATE FOR SURROUNDING FIRE.
Fire Fighting Procedures:USE NIOSH APPRVD SCBA & FULL PROT EQUIP .
WATER SPRAY MAY BE INEFTIVE. WATER SPRAY MAY BE USED TO COOL CLSD
CNTNRS TO PVNT PRESS BUILD-UP & POSS (SUPDAT)
Unusual Fire/Explosion Hazard:KEEP PROD AWAY FROM HEAT, SPKS, FLAME &
OTHER SOURCES OF IGNIT (IE, PILOT LIGHTS, ELEC MOTORS, STATIC
ELEC). INVISIBLE VAPS CAN TRAVEL TO SOURCE OF (SUPDAT)

Accidental Release

Spill Release Procedures:PROVIDE MAXIMUM VENT. ONLY PERS EQUIPPED
W/PROPER NIOSH APPRVD RESP & SKIN & EYE PROT SHOULD BE PERMITTED IN
AREA. REMOVE ALL SOURCES OF IGNIT. TAKE UP SPILLED MATL W/SAND,
VERMICULITE OR OTHER NONCOM BUST ABSORB MATL & PLACE IN CLEAN,
EMPTY (ING 14)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:DO NOT STORE ABOVE 120F (48C).
Other Precautions:VAPORS MAY COLLECT IN LOW AREAS. IF THIS MATL IS PART
OF MULTIPLE COMPONENT SYSTEM, READ MSDS(S) FOR OTHER COMPONENT OR
COMPONENTS BEFORE BLENDING AS THE RESULTING MIXTURE MAY HAVE
HAZARDS OF ALL OF I TS PARTS. CNTNRS SHOULD BE (ING 15)

Exposure Controls

Respiratory Protection:WHERE VENT IS INADEQ USE NIOSH APPRVD (TC-23C-)
AIR PURIFYING OR AIR SUPPLIED (TC-19C-) RESP. READ RESP MFR'S
INSTRUCTIONS & LITERATURE CAREFULLY TO DETERM TYPE OF AIRBORNE
CONTAMINANTS AGAINST WHICH RESP EFTIVE & HOW IT IS TO BE FITTED.
Ventilation:PROVIDE GENERAL DILUTION OR LOCAL EXHAUST VENT IN VOLUME &
PATTERN TO KEEP CONC OF INGREDS LISTED IN INGRED (ING 16)
Protective Gloves:IMPERMEABLE MATERIAL.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPROVED EYE WASH & DELUGE SHOWER .
WEAR PROT CLTHG. NO SPECIFIC PERMEATION/DEGRADATION TESTING HAS
(ING 18)
Work Hygienic Practices:CLEAN CONTAMINATED CLOTHING AND SHOES.
Supplemental Safety and Health
FIRE FIGHT PROC: AUTOIGNIT/EXPLO WHEN EXPOSED TO EXTREME HEAT. IF WATER
IS USED, FOG NOZZS ARE PREF. EXPLO HAZ: IGNIT & FLASH BACK. DO NOT
SMOKE WHILE USING PROD. KEEP CNTNRS TIGHTLY CLOSED WHEN NOT I N
USE. CLOSED CNTNRS MAY EXPLODE WHEN OVERHEATED. DO NOT APPLY TO HOT
SURFACES. TOXIC GASES MAY FORM WHEN THIS (ING 5)

Chemical Properties

Boiling Pt:B.P. Text:>212F,>100C
Vapor Pres:17.4
Vapor Density:HVR/AIR
Spec Gravity:1.367
Evaporation Rate & Reference:35 (BUOAC=100)
Solubility in Water:53.2%
Appearance and Odor:VISCOUS LIQUID W/ODOR CHARACTERISTIC OF THE
SOLVENTS LISTED IN INGRED SECTION.
Percent Volatiles by Volume:72.470

Stability

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG ALKALIES, STRONG MINERAL ACIDS OR STRONG
OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:MAY PRODUCE THE FOLLOWING DECOMP PRODS
WHEN EXPOSED TO EXTREME HEAT: OXIDES OF ALUMINUM; CARBON MONOXIDE,
(ING 6)

Disposal

Waste Disposal Methods:WASTE MATERIAL MUST BE DISPOSED OF IN ACCORDANCE
WITH FEDERAL, STATE, PROVINCIAL AND LOCAL ENVIRONMENTAL CONTROL
REGULATIONS. EMPTY CONTAINERS SHOULD BE RECYCLED OR DISPOSED OF
THROUGH AN APPROVED WAS TE MANAGEMENT FACILITY.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.