Product ID:LEA COMPOUND PLASTICLAD, B-31
MSDS Date:02/25/1993
FSC:5350
NIIN:00N089622
Status Code:A
MSDS Number: CHVJQ

JACKSONLEA/JASON INC

237 EAST AURORA ST
WATERBURY, CT 06708
US

Emergency Phone: 800-424-9300(CHEMTREC)

Info Phone: 203-753-5116

Preparer: WILLIAM M. DOWNING

Cage: JO395

JASON INC

WATERBURY, CT 06705-3830 US

Telephone: 203-753-5116

Cage: 75554

GELATINE

CAS: 9000-70-8

RTECS: LX8580000

Fraction By Weight: 6-14%

OSHA PEL N/K

ACGIH TLV: N/K

3); (ALUMINUM OXIDE ABRASIVE) (SARA 313)

CAS: 1344-28-1

RTECS: BD1200000

Fraction By Weight: 55-65%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST

IRON OXIDE

CAS: 1317-61-9

Fraction By Weight: 2-7%

OSHA PEL 10 MG/M3

ACGIH TLV: 5 MG/M3

BURNT UMBER PIGMENT; (UMBER)

CAS: 12713-03-0

Fraction By Weight: <1%

OSHA PEL N/K

ACGIH TLV: N/K

NON-REGULATED MATERIALS

RTECS: 9999999ZZ

Fraction By Weight: 13-36%

OSHA PEL N/K

ACGIH TLV: N/K

MIXTURE COMBUSTIBLE. ADDN OF METAL DUST LIKE

RTECS: 9999999ZZ

BUFFING CMPD MAY MAKE MIXTURE COMBUST. ADDN OF METAL

RTECS: 9999999ZZ

LINT & DRIED BUFFING CMPD MAY INCR MIX'S DEGREE OF

RTECS: 9999999ZZ

RECOMMENDED EXTINGUISHING MEDIA. FOR BUFFING CMPD

RTECS: 9999999ZZ

FLOODING, CHEM FOAM OR CARBON DIOXIDE.

RTECS: 9999999ZZ

SMOTHERING. INDIVIDUAL SITUATIONS WILL VARY

RTECS: 9999999ZZ

BE QUESTIONED AS TO RECOMMENDED FIRE FIGHTING MEDIA

RTECS: 9999999ZZ

EQUIP W/NO VENT TO BE APPROXIMATELY 1.4 MG/M3

RTECS: 9999999ZZ

CONSULT STANDARDS FOR DESIGN.

RTECS: 9999999ZZ

EMPLOYEES & WARN YOUR CUSTOMERS (IN EVENT OF

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:NO HAZARD IS EXPECTED FROM THE UNUSED
PRODUCT. DURING BUFFING OPERATIONS DUST MAY IRRITATE THE SKIN OR
DAMAGE THE OUTER SURFACE OF THE EYE BY ABRASIVE ACTION. INGESTION
MAY CAUSE GASTROINTESTINAL DIST URBANCES.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SYMPTOMS WHICH MAY OCCUR FROM INADEQUATE
PROTECTION DURING A BUFFING OPERATION ARE DISTURBED EYE VISION AND
OR SKIN IRRITATION.
Medical Cond Aggravated by Exposure:DERMATITIS.

First Aid:EYES: FLUSH WITH WATER FOR AT LEAST 15 MINUTES. SKIN: WASH
WITH SOAP AND WATER. INGESTION OF LARGE AMOUNTS: INDUCE VOMITING.
GROSS INHALATION: REMOVE TO FRESH AIR. SEEK MEDICAL ATTENTION AS
NEEDED.

Flash Point:>350F,>177C
Extinguishing Media:WATER FOG, FOAM, DRY CHEMICAL, CARBON DIOXIDE.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA AND FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:WATER OR FOAM MAY CAUSE VIOLENT FROTHING,
ESP IF SPRAYED DIRECTLY INTO BURNING LIQ. AFTER BUFFING CMPDS HAVE
BEEN USED THERE IS NORMALLY PRDCED A WASTE (SUPDAT)

Spill Release Procedures:WEAR PROT CLTHG. RECLAIM FOR REUSE IF POSSIBLE
OR SWEEP, SCOOP UP & CONTAINERIZE FOR LATER DISPOSAL. THIS PROD IS
NOT A HAZARDOUS WASTE BY ITSELF, BUT BE SURE TO CHECK IF IT HAS
COME IN CONTACT W/HAZA RDOUS SUBSTANCES OR MATERIAL BEFORE
DISPOSAL.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:KEEP OUT OF SUN & AWAY FROM HEAT
SOURCES. PROTECT PASTE OR LIQ PRODS FROM FREEZING. OBSERVE ALL
SAFEGUARDS FOR CNTNR RESIDUE UNTIL CLEANED/DESTROYED.
Other Precautions:DURING A BUFFING OPERATION, USE EXHST, EYE PROT,
CLTHG & GLOVES TO PVNT CMPD DUST OR MATL BEING REMOVED DURING
BUFFING FROM ENTERING NOSE, THROAT &/OR SKIN OF OPERATOR. OSHA
STUDIES HAVE FOUND BRTHG Z ONE CONCENTRATION FOR BUFFING (ING 13)

Respiratory Protection:DURING BUFFING USE NIOSH APPROVED DUST/MIST
RESPIRATOR SIMILAR TO #3710 FROM 3M.
Ventilation:LOCAL EXHAUST: WHEN AIRBORNE EXPOS LIMITS ARE EXCEEDED
DURING USE. MECHANICAL (GENERAL): ADEQ FOR STORAGE & (ING 14)
Protective Gloves:HEAVY DUTY GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPROVED EYE WASH & DELUGE SHOWER . SEE
SECTION ON PRECAUTIONS FOR SAFE HANDLING & USE.
Work Hygienic Practices:WASH AFTER PHYSICAL CONTACT & BEFORE EATING. DO
NOT PERMIT DUST TO ACCUMULATE IN WORK AREA. TRAIN YOUR (ING 15)
Supplemental Safety and Health
EXPLO HAZ: CONTAINING DRIED BUFFING CMPD, BUFFING WHEEL LINT OF COTTON,
POLYESTER, ETC (DETERMINED FROM BUFFING WHEEL VENDOR), PLUS DUST
FROM MATL THAT WAS POLISHED. USE OF EXTING MEDIA IN FIRE FROM T HIS
WASTE SHOULD BE EVALUATED AS THE THE MATL THAT WAS POLISHED. FIBRE
LINT W/DRIED BUFFING CMPD MAY MAKE THE (ING 6)

Spec Gravity:2-2.2 (H*2O=1)
pH:NEUT
Solubility in Water:APPRECIABLE
Appearance and Odor:SOLID DENSE BRICK WITH MILD ODOR - COLOR BROWN.

Stability Indicator/Materials to Avoid:YES
NONE KNOWN.
Stability Condition to Avoid:NONE KNOWN.
Hazardous Decomposition Products:CARBON AND SMOKE.

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH ALL LOCAL, STATE
AND FEDERAL REGULATIONS. WASTE GENERATED FROM A BUFFING OPERATION
CAN CONTAIN LINT WHICH MAY BE COMBUSTIBLE.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.