Product ID:EPOXY REPAIR STICK(PUTTY), 108015
MSDS Date:01/14/1999
FSC:8030
NIIN:00N091601
Status Code:A
MSDS Number: CJPXR

Emergency Phone: 800-424-9300

Info Phone: 513-489-7600

Cage: 18731

Telephone: 513-489-7600

Cage: 18731

1-CHLORO-2,3-EPOXYPROPANE-4,4'-ISOPROPYLIDENEDIPHENOL

CAS: 25068-38-6

RTECS: CE6880000

PHENOL,

CAS: 90-72-2

RTECS: SN3500000

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: EYES: CONTACT WITH LIQUID MAY
RESULT IN IRRITATION, REDNESS, TEARING AND POSSIBLE MINOR TEMPORARY
CORNEAL INJURY. SKIN: CONTACT WITH WET MATERIAL MAY RESULT IN
IRRITATION OF SKIN AND MAY BE A S KIN SENSITIZER. INHALATION:
EXCESSIVE INHALATION OF VAPORS MAY CAUSE NASAL AND RESPIRATORY
IRRITATION, ACUTE NERVOUS SYSTEM DEPRESSION, OR LUNG INJURY.
INGESTION: MAY CAUSE GASTROINTESTINAL IRRITATION , DIARRHEA, AND
VOMITING. CHRONIC: NONE KNOWN.
Effects of Overexposure:SEE HEALTH HAZARDS.

First Aid:EYES: FLUSH IMMEDIATELY WITH LARGE AMOUNTS OF WATER FOR AT
LST 15 MINUTES. SEE PHYSICIAN FOR MEDICAL TREATMENT. SKIN:
IMMEDIATELY WASH AFFECTED AREA WITH SOAP AND WATER. REMOVE
CONTAMINATED CLOTHING. CONSULT PHYSICIAN IF IRRITATION DEVELOPS.
INHAL: REMOVE PERSON TO FRESH AIR. RESTORE BREATHING. KEEP PERSON
WARM AND QUIET. TREAT SYMPTOMATICALLY. GET MEDICAL ATTENTION.
INGESTION: KEEP PERSON WARM AN D QUIET. CONSULT PHYSICIAN OR POISON
CONTROL CENTER IMMEDIATELY.

Flash Point:NONE
Extinguishing Media:COMBUSTIBLE LIQUID - CLASS III B. FOAM, WATER
SPRAY, CARBON DIOXIDE, AND DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA AND FULL PROTECTIVE
EQUIPMENT . WATER MAY BE USED TO COOL CONTAINERS TO PREVENT
PRESSURE BUILD-UP WHICH MAY RUPTURE CONTAINERS.
Unusual Fire/Explosion Hazard:AT ELEVATED TEMPS, SUCH AS IN FIRE,
POLYMERIZATION MAY TAKE PLACE. IF POLYMERIZATION TAKES PLACE IN CLD
CNTNR MAY CAUSE RUPTURE. PROD VAPS MAY FORM EXPLOSIVE MIX IN AIR.
POLYMERIZATION EVOLVES LG QTYS OF HEAT, WHICH COULD CAUSE FIRE IF
NOT CONTROLLED.

Spill Release Procedures:REMOVE ALL SOURCES OF IGNITION. VENTILATE THE
AREA. WEAR PROTECTIVE EQUIPMENT (SEE SPECIAL PROTECTION INFORMATION
SECTION H). AVOID BREATHING VAPORS. CONTAIN SPILL. COLLECT WITH
INERT ABSORBENT AND RE MOVE. DISPOSE OF PROPERLY.

Handling and Storage Precautions:STORE MATERIAL IN A COOL,
WELL-VENTILATED AREA. DO NOT STORE AT TEMPS ABOVE 75F. DO NOT USE
OR STORE NEAR HEAT, SPARKS/OPEN FLAME. KEEP CONTAINERS TIGHTLY
CLOSED. AVOID CONT W/INCOMPATIBLE MATLS. REAC TION WITH AMINES &
EPOXY HARDENERS WILL RELEASE HEAT.
Other Precautions:PRODUCT MUST BE MIXED W/EPOXY HARDENER TO USE. PLEASE
REFER TO MSDS FOR HARDENER(B) BEFORE USING. IF PROD IS TO BE
SANDED, PEL/TLV OF 10 MG/M3 FOR NUISANCE DUSTS SHOULD BE OBSERVED.
KEEP OUT OF REACH OF CHILDREN. DO NOT TAKE INTERNALLY. AVOID
CONTACT WITH EYES AND SKIN.

Respiratory Protection:USE NIOSH-APPROVED RESPIRATORS DESIGNED TO
REMOVE PARTICULATE MATTER AND ORGANIC SOLVENT VAPORS.
Ventilation:GEN DILUTION/LOC EXHST VENT SHOULD BE PROVIDED TO KEEP
EXPOSURES BELOW ACCEPTABLE LIMITS (SECTION B - HAZARDOUS
INGREDIENTS) AND TO KEEP (SUPDAT)
Protective Gloves:NEOPRENE OR NATURAL RUBBER.
Eye Protection:ANSI APPROVED CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:EYE WASH & DELUGE SHWR MTG ANSI DESIGN CRIT
. PROT GLOVES & PROPER CLTHG SHOULD BE WORN TO PVNT SKIN CONT.
BARRIER CREAM MAY BE WORN FOR ADDNL SKIN PROT. IMPERM CLTHG SHOULD
NOT BE WORN (SUPDAT)
Work Hygienic Practices:ALWAYS WASH HANDS AFTER USING THIS MATERIAL,
AND BEFORE EATING, DRINKING, OR SMOKING.
Supplemental Safety and Health
VENT: SOLVENT VAPORS BELOW THE LOWER EXPLOSION LIMIT. OTHER PROT EQUIP:
TO PREVENT PROLONGED/REPEATED CONT OF WET MATL WITH THE SKIN.

Vapor Density:HVR/AIR
Evaporation Rate & Reference:SLOWER THAN ETHYL ETHER
Percent Volatiles by Volume:0

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZERS, ACIDS, BASES, AMINES, AND EPOXY HARDENERS UNDER
UNCONTROLLED CONDITIONS.
Stability Condition to Avoid:HEAT, INCOMPATIBLE MATERIALS, AND WARM
STORAGE.
Hazardous Decomposition Products:FUMES MAY BE PRODUCED WHEN MATL IS
HEATED TO DECOMPOSITION. FUMES MAY CONTAIN CARBON MONOXIDE, CARBON
DIOXIDE, VARIOUS HYDROCARBONS, AND IRRITATING ACRID FUMES.

Waste Disposal Methods:DISPOSE OF I/A/W FEDERAL, STATE, & LOCAL REGS.
WASTE FROM THIS PROD MAY BE HAZ AS DEFINED UNDER RCRA 40 CFR 261.
WASTE MUST BE TESTED FOR IGNITABILITY TO DETERM APPLICABLE EPA HAZ
WASTE NUMBERS. BEFOR E ATTEMPTING CLEAN-UP OR DISPOSING OF MATL,
REFER TO HAZARD INFO IN OTHER SECTION OF THIS SHEET.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.