CLFGM - INTERVIRON A/F BLACK BRA642
- MSDS: CLFGM
- Manufacturer: COURTAULDS COATINGS INC INTERNATIONAL
- Product Name: INTERVIRON A/F BLACK BRA642
- National Stock Number: 8010-01-339-8707
Product Identification
Product ID:INTERVIRON A/F BLACK BRA642
MSDS Date:12/17/1996
FSC:8010
NIIN:01-339-8707
Status Code:A
MSDS Number: CLFGM
Responsible Party
HOUSTON, TX 77091
US
Emergency Phone: (800)424-9300
Info Phone: 713-684-1563
Preparer: HENRY SIMMONS
Cage: 028S6
Contractor
Telephone: 713-684-1244
Cage: 028S6
Ingredients
COPPER
CAS: 7440-50-8
RTECS: GL5325000
OSHA PEL 1 MG/M3
ACGIH TLV: 1 MG/M3
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
ZINC OXIDE (ZNO)
CAS: 1314-13-2
RTECS: ZH4810000
OSHA PEL 15 MG/M3
XYLENE
CAS: 1330-20-7
RTECS: ZE2100000
ACGIH TLV: 434 MG/M3;100 PPM
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
N-BUTYL ALCOHOL
CAS: 71-36-3
RTECS: EO1400000
OSHA PEL 300 MG/M3;100 PPM
EPA Report Quantity: 5000 LBS
DOT Report Quantity: 5000 LBS
CUPRIC OXIDE
CAS: 1317-38-0
RTECS: GL7900000
CUPROUS OXIDE
CAS: 1317-39-1
RTECS: GL8050000
ETHYLBENZENE
CAS: 100-41-4
RTECS: DA0700000
OSHA PEL 435 MG/M3;100 PPM
ACGIH TLV: 434 MG/M3;100 PPM
EPA Report Quantity: 1000 LBS
DOT Report Quantity: 1000 LBS
CADMIUM
CAS: 7440-43-9
RTECS: EU9800000
OSHA PEL see 1910.1027
EPA Report Quantity: 10 LBS
DOT Report Quantity: 10 LBS
Hazards
Effects of Overexposure:INHALATION: CAUSES NOSE AND THROAT IRRITATION.
HARMFUL IF INHALED. MAY AFFECT THE
BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE OR NAUSEA. EYE
CONTACT: CAUSES
EYE IRRITATION. SKIN CONTACT: CAN BE ABSORBED THROUGH THE SKIN. MAY
CAUSE ORGAN
DAMAGE. CAUSES SKIN BURNS. INGESTION: MAY BE FATAL IF SWALLOWED AND MAY
CAUSE ORGAN
DAMAGE.
First Aid
First Aid:INHALATION: REMOVE TO FRESH AIR. IF DISCOMFORT IS PRESENT OR
BREATHING IS ABSENT GET
MEDICAL ATTENTION IMMEDIATELY. EYE CONTACT: FLUSH IMMEDIATELY WITH
PLENTY OF
WATER FOR 15 MINUTES UNTIL IRRITATION SUBSIDES. IF IRRITATION PERSISTS,
GET MEDICAL
ATTENTION. SKIN CONTACT: FLUSH WITH LARGE AMOUNTS OF WATER. USE SOAP IF
AVAILABLE.
REMOVE SEVERELY CONTAMINATED CLOTHING (INCLUDING SHOES) AND WASH BEFO
RE REUSE. IF
IRRITATION PERSIST, GET MEDICAL ATTENTION. INGESTION: IF SWALLOWED, DO
NOT INDUCE
VOMITING. KEEP AT REST. GET PROMPT MEDICAL ATTENTION.
Fire Fighting
Flash Point:=26.7C, 80.F
Lower Limits:.6
Extinguishing Media:FOAM, CARBON DIOXIDE, DRY CHEMICAL
Unusual Fire/Explosion Hazard:ISOLATE FROM HEAT, SPARKS, ELECTRICAL
EQUIPMENT AND OPEN FLAME. CLOSED CONTAINERS MAY EXPLODE WHEN
EXPOSED TO EXTREME HEAT. IN THE ABSENCE OF ELECTRICITY, A WATER
SPRAY (A FOG NOZZLE IS PREFERRED) MAY BE USED TO COOL CONTAINERS.
DECOMPOSITION AND COMBUSTION PRODUCTS MAY BE TOXIC.
Accidental Release
Spill Release Procedures:CONTAIN SPILLED LIQUID WITH SAND OR EARTH. DO
NOT USE COMBUSTIBLE MATERIALS SUCH AS
SAWDUST. ABSORB SPILL WITH AN INERT MATERIAL (E.G., DRY SAND OR EARTH),
THAN PLACE IN A
CHEMICAL WASTE CONTAINER.
Handling
Handling and Storage Precautions:KEEP CONTAINER CLOSED. LOOSEN CLOSURE
CAUTIOUSLY BEFORE OPENING. STORE IN A COOL,
WELL VENTILATED PLACE AWAY FROM INCOMPATIBLE MATERIALS. KEEP AWAY FROM
HEAT,
SPARKS AND FLAMES. PROTECT MATERIAL FROM DIRECT SUNLIGHT. GROUND AND
BOND
CONTAINERS WHEN TRANSFERRING MATERIALS.
Exposure Controls
Respiratory Protection:USE A RESPIRATOR JOINTLY APPROVED BY MINE SAFETY
AND HEALTH ADMINISTRATION OF THE DEPARTMENT OF LABOR AND THE
NATIONAL INSTITUTE FOR OCCUPATIONAL SAFETY AND HEALTH OF THE
DEPARTMENT OF HEALTH AND HUMA N SERVICES AND IN ACCORDANCE WITH
29CFR 1910.134.
Ventilation:PROVIDE SUFFICIENT VENTILATION, IN VOLUME AND PATTERN TO
KEEP THE TLV OF THE HAZARDOUS INGREDIENTS BELOW THE LIMIITS LISTED
IN SECTION II.
Protective Gloves:WEAR CHEMICAL RESISTANT GLOVES.
Eye Protection:SAFETY GLASSES, CHEMICAL GOGGLES AND/OR A FACE SHIELD.
Supplemental Safety and Health
Chemical Properties
Melt/Freeze Pt:=117.2C, 243.F
Vapor Density:>AIR
Spec Gravity:2.178
Evaporation Rate & Reference:SLOWER/ETHER
Appearance and Odor:LIQUID
Stability
Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS
Stability Condition to Avoid:STRONG OXIDIZING AGENTS.
Hazardous Decomposition Products:MAY PRODUCES HAZARDOUS FUMES WHEN
HEATED TO DECOMPOSITION AS IN WELDING. FUMES MAY PRODUCE CARBON
DIOXIDE AND CARBON MONOXIDE.
Disposal
Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE, AND
FEDERAL REGULATIONS. DO NOT
INCINERATE UNOPENED CONTAINERS.
Toxicology
Toxicological Information:THERE IS NO DATA AVAILABLE ON THE PRODUCT
ITSELF. NOTICE: REPORTS HAVE ASSOCIATED REPEATED AND PROLONGED
OCCUPATIONAL OVEREXPOSURE TO SOLVENTS WITH PERMANENT BRAIN AND
NERVOUS SYSTEM DAMAGE. INTENTION AL MISUSE BY DELIBERATELY
CONCENTRATING AND INHALING THE CONTANTS CAN BE HARMFUL OR FATAL.
Regulatory
SARA Title III Information:313 REPORTING INGREDIENTS. 71-36-3 N-BUTYL
ALCOHOL. 100-41-4 ETHYLBENZNE. 1314-13-2 ZINC OXIDE. 1330-20-7
XYLENE. 7440-43-9 CADMIUM. 7440-50-8 COPPER.
Federal Regulatory Information:TSCA (TOXIC SUBSTANCE CONTROL ACT);
COMPONENTS OF THIS PRODUCT ARE LISTED ON THE TSCA INVENTORY. CERCLA
(COMPREHENSIVE COMPENSATION AND LAIBILITY ACT): WE RECOMMAND YOU
CONTACT LOCAL AUHORITIES TO DET ERMINE IF THERE MAY BE OTHER LOCAL
REPORTING REQUIREMENTS.
State Regulatory Information:
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.