Product ID:HYSOL EA 9394 PART A
MSDS Date:07/08/1997
FSC:8040
NIIN:01-169-5304
Status Code:A
MSDS Number: CLMJB

DEXTER AEROSPACE MATERIALS DIVISION

510-458-8000,X262 OR 263
PITTSBURG

Emergency Phone: 800-424-9300

Info Phone: 800-424-9300(CHEMTREC)

Preparer: ERNEST CARTER

Cage: 33564

DEXTER CORPORATION ADHESIVE & COATING SYSTEMS

312 BAY POINT, CA 94565-3299 US

Telephone: 202-483-7616

Cage: 33564

ALUMINUM POWDER

CAS: 7429-90-5

RTECS: BD0330000

OSHA PEL 15 MG/M3

ACGIH TLV: 10 MG/M3

BISPHENOL A/EPICHLOROHYDRIN EPOXY RESIN

POLYFUNCTIONAL EPOXY RESIN

SILICA

CAS: 112945-52-5

RTECS: VV7310000

OSHA PEL 6 MG/M3

ACGIH TLV: 6 MG/M3

Explanation of Carcinogenicity:NEITHER THIS MATERIAL NOR ANY OF ITS
COMPONENTS IS CONSIDERED A CARCINOGEN.
Effects of Overexposure:SKIN OR EYE IRRITATION, CHEST DISCOMFORT. THIS
MATERIAL IS CORROSIVE TO EYES AND SKIN. BRIEF CONTACT MAY CAUSE
CHEMICAL BURNS. VAPORS AND MISTS WILL IRRITATE NOSE AND THROAT.
LONG TERM EFFECTS: REPEA TED OR PROLONGED SKIN CONTACT MAY RESULT
IN BURNS AND POSSIBLEALLERGIC SENSITIZATION.
Medical Cond Aggravated by Exposure:SKIN SENSITIZATION

First Aid:EYE: FLUSH EYES WITH WATER FOR 15 MINUTES. SKIN: WASH SKIN
THOROUGHLY WITH SOAP AND WATER. INHALATION: REMOVE VICTIM TO FRESH
AIR. INGESTION: DRINK PLENTY OF WATER. GET MEDICAL ATTENTION
IMMEDIATEL Y.

Extinguishing Media:DRY CHEMICAL, OR HALON FIRE EXTINGUISHER, OR WATER
SPRAY, FOAM OR FOG.
Fire Fighting Procedures:WEAR SELF-CONTAINED BREATHING APPARATUS AND
FULL PROTECTIVE CLOTHING. SUCH AS TURN OUT GEAR. CARTRIDGE
RESPIRATORS DO NOT PROVIDE ADEQUATE PROTECTION FOR FIRE FIGHTERS OR
EXOTHERN MITIGATION.
Unusual Fire/Explosion Hazard:MAY LIBERATE LARGE QUANTITIES OF DENSE
FOUL-SMELLING SMOKE WHICH MAY CONTAIN UNIDENTIFIED TOXIC GASSES.

Spill Release Procedures:WEAR PROTECTIVE CLOTHING, GLOVES AND SAFETY
GLASSES. ABSORB SPILL WITH SORBENT MATERIAL. SUCH AS VERMICULITE OR
SAND. SCRAPE UP OR SHOVEL INTO DOT APPROVED WASTE CONTAINERS.

Handling and Storage Precautions:REFRIGERATED STORAGE IS RECOMMENDED TO
MAINTAIN PRODUCT QUALITY. THIS PRODUCT MAY BE STORED AT 40 DEG. F
FOR UP TO 12 MONTHS. FOLLOW CURING SCHEDULE AS RECOMMENDED IN
PRODUCT LITERATURE.
Other Precautions:DO NOT CUT, GRIND, WELD, OR DRILL ON OR NEAR THIS
CONTAINER.

Respiratory Protection:IF LOCAL EXHAUST VENTILATION IS ADEQUATE, A
RESPIRATOR EQUIPPED WITH ORGANIC VAPOR CARTRIDGES MAY BE
APPROPRIATE.
Ventilation:LOCAL EXHAUST VENTILATION.
Protective Gloves:WEAR BUTYL RUBBER, PVC, OR NITRILE RUBBER GLOVES.
Eye Protection:WEAR SAFETY GLASSES WITH SIDE SHIELDS OR CHEMICAL
GOGGLES.
Other Protective Equipment:AN EYEWASH AND SAFETY SHOWER SHOULD BE
NEARBY AND READY FOR USE.
Supplemental Safety and Health

Vapor Pres:MMHG: NIL
Vapor Density:AIR=1
Spec Gravity:WATER=1: 1.45
Viscosity:P: 4000-8000
Solubility in Water:NEGLIGIBLE
Appearance and Odor:PASTE VISCOUS GRAY PASTE WITH SLIGHT ODOR

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS.
Stability Condition to Avoid:AVOID MIXING RESIN (PART A) AND CURING
AGENT (PART B ) IN BATCHES GREATER THAN 1 POUND UNLESS YOU PLAN TO
USE IMMEDIATELY. DO NOT HEAT MIXED ADHESIVE ABOVE 125 DEG. F.
FAILURE TO OBS
Hazardous Decomposition Products:CO, NOX, ALDEHYDES, ACIDS AND
UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:MAY OCCUR.

Waste Disposal Methods:THIS MATERIAL, AS A WASTE, IS NOT CONSIDERED A
RCRA HAZARDOUS WASTE. HOWEVER, INCINERATION IN AN EPA APPROVED
WASTE INCINERATOR IS A PREFERRED DISPOSAL PRACTICE.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.